Mechanical Skid Mounted Drilling Rig for Sale
1000hp Land Drilling Rig for Sale

Description

1  1000HP Mechanical Skid Mounted Drilling Rig, assembled and manufactured
in 2007/8 (brand new).
Drawworks/Mast - Skid. The skid is designed to move in 1 load, is covered
completely regarding noise reduction and houses the following equipment:
Engines and power unit, drawworks, hydraulic system, floor-winches, deadline anchor,
Transport dimension: 17.0m long x 3.0m wide x 2.4m high (without mast)
Transport weight: approx. 55 tons.

Mast
Guyed, telescoping vertical mast, built in accordance with API 4F.
Max hook load 2000kN (on 10 lines)
Clear height above drill floor is 32.6m (107 ft)
Mast main legs to be air pressure tested.
2    3-stage hydraulic cylinders (chrome plated) for raising the mast, with safety 
chokes to prevent freefall.
2   Single acting, chromed telescoping cylinders for raising the top section.
The block assembly uses all steel sheaves grooved for 1- 1/4" line, mounted 
on tapered roller bearing inserts:
4  36" Fleet sheaves - grooved for 1-1/4" drill line
1 42" fastline sheave - grooved for 1-1/4" drill line
1 36" Deadline sheave - grooved for 1-1/4" drill line
1 24" Sandline sheave - grooved for 9/16" drill line
2 Sets of sheaves mounted on crown for two winch lines.
8  Guylines for internal guying.
1 Torque tube hanging lug (the mast is designed to accommodate a 
Tesco 250 HMIS 475HP Top Drive).

Racking Board
Fingers with 5 in. spacing for up to 4-1/2 in. drill pipe.
Capacity for 11,500 ft. of 4-1/2 in. drill pipe with 6-1/4 in. tool joint.
Complete with rear escape system, type: RG 10D.
Windwall protection 2.5m high around racking board on 3 sides, made of 
steel frame covers.
Auxiliary winch 6kN for pipe handling, air pressure driven, type: LS2-600R.

Make-Up and Break-Out Assembly
2 Make and break hydraulic cylinders 5" x 96", sheaves, rollers and cables, 
mounted on back of mast.
Hydraulic controls for make- up and break-out functions on driller's cabin.

Manifold
Seven valve 5000-psi discharge manifold, integral welded, 602 unions.
Standpipe 4", 5000-psi c/w gooseneck at the top and unions at top and 
bottom of standpipe.

Drawworks
Single drum drawworks, rated for 1000HP.
Drum size: 22" x 37"
Wireline size: 1-1/4"
Drawworks Speeds: 5 forward, 1 reverse (through engine transmissions)
Input drive chain: 1-3/4" pitch, triple strand
Band brake size: 44 x 11, c/w brake blocks and brake bands
Eaton Model WCBD-236
Circulating water-cooled, 210 gal/min of external water source, supplied 
by charge pump.

Engines
2 Detroit diesel series 60 Diesel engines, 14.0l. with intermittent rating of 
550BHP @ 2,100 rpm each.
Six cylinder, turbocharged and air to air aftercooled, with electronic motor controls
EPA Nonroad Emissions Certification
Air starter
Rig saver, water cooled exhaust manifold, spark arrestor.

Transmission
2  Allison Transmission Model S5610H series transmissions

PTO
2 Chelsea power take-offs, transmission mounted.

Compound
1 Two engine, chain driven compound with mechanical disconnects.

Right Angle Gearbox
1  Right angle gearbox supplies power to drawworks and comes complete 
with reversing box to drive rotary table with
Fawick 16VC600 clutch.

Air System
1 Centrifugal-compressor type: SM12T, air supply 0.75m/min, with air dryer.
1 200L (50 gal.) tank plumbed on skid.
1 2000l (520 gal.) main air-pressure tank located in container under the skid.

Fuel System
1 300 gal. fuel tank as day-tank, mounted on rig skid to supply all engines on the rig.
2 25m/3 fuel tank container with charge pump system to supply automatic day-tank.

Hydraulic System
Mounted on skid and supplies power for following rig/skid operations:
1 Hydraulic circuit rated at a capacity of 60 gpm@ 2500 psi, supplies hydraulic 
winches, mast raising/telescopic cylinders, make and break cylinders.
1 Hydraulic circuit rated at a capacity of 22 gpm@ 3000psi, supplies iron roughneck.
1  Hydraulic circuit rated at a capacity of 220 gpm@ 6000psi supplies top drive.
1 Hydraulic circuit rated at a capacity of 60 gpm@ 6000psi supplies automatic driller.
1 340 gal. hydraulic tank
Hydraulic filters, suction strainers, all related valves and gauges.

Winches
1 12,000LBS. hydraulic winch.
1 8,000LBS. hydraulic winch.

Deadline Anchor
1 Type: floor mounted, Model CJZ 250 incl. a tension load cell, that converts the 
deadline tension into hydraulic pressure.

Drill Line Spool Rack
1 Sufficient for 3,000ft of 1-1/4" drill line.

Substructure
Floor height: 6.85m (22.4ft)
Width working floor: 6.0m (20ft)
Length working floor: 6.75m (22ft)
Setback capacity: 1360kN
Rotary capacity: 1960kN
Rotary table opening: 570mm (27 1/2")

Travelling and Floor Equipment

Drilling Block
1 Drilling block/hook combination, 5 sheaves grooved for 1-1/4" wireline. 
Rated capacity of 250 tons.
                  
Elevator Links
1 Set of 2 elevator links, 2-1/4"x 108", acc. API 8C-PSL1. Rated capacity of 250 tons.

Swivel
1 Rotary swivel with 5-1/2" API Reg. LH Box down.
Washpipe packing assembly.
Gooseneck with tapped and plugged hole in top for use with measuring line.
4" API rotary hose connection, Fig. 602 integral welded female.  Rated capacity of 300 tons.

Rotary Table
1 27-1/2" rotary table.  Max. static capacity: 500 tons.
Split square drive master bushing.  Max speed: 220 rpm.  Max. torque: 23,500 Nm (17,300 ft-lbs).
Gear ratio: 3.16.

Rotary Drive System
1 Right angle gear box system consists of one lower RAGB mounted on skid and one 
upper RAGB mounted to mast using an 1810 drive shaft for connecting.

Rotary Torque Indicator
1 Model 2500 torque indicator system

Torque Wrench and Spinner
1 Gray Floorhand GF1000 Compact roughneck.  Upper and lower clamp for make-up 
and break-out operations.
Breakout torque: 108,000 Nm (80,000ft-lbs)
Makeup torque: 88,000 Nm (65,000ft-lbs)
Spinner: 80....100rpm. Max. torque: 2200Nm (1,600 ft-lbs)
Hydraulic supply requirements: 25 GPM, 2,500psi.

Spring Slips
1 Cam-Tech C-AS 16-5500

Mud Pumps and Mud System

Mud Pumps

2 WS-1000 Quadraplex Mud Pump 1000HP.  Discharge connection: 4 1/16" API 5000 RTJ.
Liner & piston sizes: 4"  7 1/2".    Stroke: 254mm (10").
Engine: Detroit Diesel S-2000 16 cyl. 820kW with air starter and complete control panel.
Torque converter: Voith type 562 TPKD 01-SAE .   Engine is covered for noise reduction.

Mud Tanks
1 Modular tank system, consists of 8 tanks with a gross nominal capacity of 105m/2.

Shaker
3 Linear motion shale Shaker "Black Thunder" Serie 4236-3P-15X.

Desilter
2 12 cone desilter.

Mud Agitator
7 Type:SR, 2.5 kW, 400V-Motor explosion proof electric motor, 50Hz.

Vacuum Degasser
1 Type: VAK 1000 nominal flow 1000GPM.

Centrifugal Pumps
3 Type: 250 "Magnum" 6x5x14, hard iron casing.  400v motor explosion-proof 
electric motor, 58kW, 50Hz.
For desilter, pill tank and mixing operations (hopper).

Trip Tank
1 Trip tank with a capacity of 2.5 m/2.  Centrifugal transfer pump type: 250 "Magnaum" 3 x 2 x 13.

Shaker/Cutting Tank
1  40m/2 tank.

Drilling Instrumentation

Drillers Cabin
1 The drillers control cabin is a complete unit that contains: driller's control chair 
with joy stick controls (drawworks) and top drive controls.  Remote BOP controls.  
Cabin windows with wipers to provide full view of rig floor, mast and monkey board.
Drill monitoring system and data processing (GeoData) with touch screen monitor.
LCD monitor 17" with 2 cameras for video system (observation of drawworks and monkey board.)

Well Control and Choke Manifold

BOP Equipment

1 21 1/4" Annular BOP Type "MSP", 2,000psi.
1  20 3/4" Double Ram BOP Type: "V" API 3,000 RTJ.
1 13 5/8" Annular BOP Type "GK" API 5,000RTJ.
1 13 5/8" Double Ram BOP, Type "U" , API 5,000 RTJ.

BOP Control System
1 BOP Control unit, Atex and CE certified, complete mounted on skid.  
27 Accumulator @ 10 gal. (38l).
3,000 psi working pressure, 4,500psi test pressure.  Fluid reservoir tank 320 gal. (1200l).
1  Electric driven triplex pump CAD 3517 with 24 5kW motor, 400V, 
50Hz flow rate 14GPM (53l/min)
2  Air pump motor modul 8 1/2" ratio 60:1
1  Operators remote control panel, complete with all valves, gauges and controls.

Choke Manifold
1  3 1/8" API 5,000, compl. assembly, test, blast and paint.

Additional Rig Equipment/Certifications

1 550 kVA electric generator, 50Hz, 400/230V.
Engine: Volvo Penta TAD 1641 GE, 6 cyl. 16.1 L, complete mounted on a skid, soundproofed.

1 400 kVA electric generator 50Hz, 400/230V.
Engine: Volvo Penta TAD 1242 GE, 6 cyl. 12.1 L.  Complete mounted on a skid, soundproofed.
6 Containers for the rig crew.

1 Electrical and mechanical ATEX- Certification (German standard).
1 CE declaration.
1 Full operation and maintenance manual for all parts of the rig in English/German.

Drill pipes   3 1/2"                  5"                        2-7/8"
                 3100m                2010m                   1000m

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

----------------------------------------------------------------------------------------------------------
Search words (for official use only) :
1000HP Mechanical Skid Mounted Drilling Rig
2007/8 Built Mechanical Skid Mounted Drilling Rig
Land Drilling Rig 1000hp
Mechanical Skid Mounted Drilling Rig for Sale
1000hp Mechanical Drilling Rig for Sale
----------------------------------------------------------------------------------------------------------