Specifications |
: |
Hot Oil Unit for Sale
Hot Oilers for Sale
Description :
Hot oil unit fully integrated and mounted on a truck chassis cab tract.
2013 Kenworth Model T800 and / or its equivalent in other model.
Accessories and tools included.
- Specially designed for heavy or rough work. Equipped as follows:
- Heat exchanger of a single step of 85 tubes 77 inches long and 2 inches in diameter; 30 of
these tubes are finned type, for a moreefficient heat exchanger, finned coils 2 inches in diameter
A106B steel, Schedule 40 Seamless, inspection door heater 20 inches (Tempered glass with
window for high temperature), folding, located on the left side of the thermal equipment.
- Thermostatic control of heat burner. Safety pilot lights for ignition burners. Spark
ignition pilot burner. Spray water heated by water. Gas vaporized heated by water.
Pre-heater 1-inch propane burner box. Safety switch installed immediately stop
the fuel line (LPG) generator and the internal combustion engine (Kill Switch).
- Alarm Gas Leak Detector. Automatic and manual operation installed to the inner side of the
operation panel. 4 boxes of heavy tools included, without division, two on each side of the
unit. Co2 system protection against fire in the heater, activated from the control panel.
Two fire extinguishers 30 pounds, one on each side, dry chemical powder and valid
warranty seal label.
Standard Tank Service :
Service tank simple, cylindrical compartment bulkhead, 75 barrels capacity, built with
carbon steel sheets of ¼ inch thick, epoxy coated inside, a door entry access man at the
top which It is 24 "in diameter.
2 pipe vent 3 inches in diameter, gooseneck on the tank and above the gas tank. Two
subsequent optical fluid levels of 5/8 "x 36" long with their sets of valves with drain tap
(red line) with side impact protection for high strength, located on the side of the tank
service, the stairs, a suction pump 12 volt diesel to facilitate cleaning of the gauges.
Stairs to tank (located on the back side of the tank and driver side) with safety
protections, railing at the top and type in the Irving grid Hall.
5 Pieces special lamps 4 x 6 rectangular, halogen, more than 200,000 candelas
power of 12 volts, 50 watts of power for outdoor work, for night operations, with
manual adjustment mechanism.
1 turret part of cab which includes:
- Halogen lamp, amber light, two halogen bulbs of 55 watts, 12 volts DC, 8 amp, a
flat mirror between rotating, 400 flashes per minute, amber polycarbonate base
and lens.
- Rack storage of hoses 3 "pipes 1 1/2" on the back of the unit under the tank service.
- 2 chemical handling tanks, located at the rear, with a capacity of 50 liters each.
- Drain valve 4 in the bottom of the Duty tank.
- Relief valve, vacuum / pressure, emergency.
Includes fixed base hinged mast 2.5 meters, cone gauge frame to place wind direction
and wind cone.
The unit has diamond signaling transport of dangerous substances according to the rules
Integrated Security Panel
Thermometer temperature gauge input and output.
Gauge high pressure gauge input and output.
Pressure gauge with adjustable points of high and low pressure and temperature to
turn off the burner unit and triggering a red light in case of emergency.
Security switch to stop the flow of fuel to the burner with light indication.
Pressure gauge to the burner.
Operation levers for controlling the pump (low pressure and high pressure).
The control panel is installed frontally next to the oven and cover has iron.
Board Indicators
Engine oil pressure, engine temperature, air pressure and tachometer.
Pump control, engine throttle and operating indicators.
Pressure Gauge 0-600 psi Booster Pump.
Control Manifold Composed of three sections, working pressure up to 6000 PSI.
Section A (suction lines).
Pipe 3-inch Schedule 40 carbon steel.
Solder connections 3 inch, Schedule 40 carbon steel.
Butterfly valve of carbon steel 3 inch carbon steel 300 PSI.
Connects carbon steel loading and unloading on each side of the drive to the rear.
Pipe Schedule 40 3 inch butterfly valve for sucking the service tank high pressure
pump. Section B (Manifold). Carbon steel pipe 2 inch Schedule 80 seamless.
Solder connections 2 inch Schedule 80 carbon steel.
2 ball valves 2 inch carbon steel high pressure (6000 PSI).
Two gate valves 2-inch black steel high pressure 1440 PSI, between the control
manifold and highpressure discharge.
2 inch pipe carbon steel seamless identification card 160.
Connectors 2 inch weld carbon steel identification card 160. Two check valves 2 inch
6000 PSI, installed between the pump high pressure (6000 PSI), the control manifold
and the discharge line. 2 swivel Unions 6000 PSI 1 ½ inches chicksan connection type.
Bypass arrangement for 6000 PSI composite pipe 1 1/2 "swivel joints chicksan type,
hit Union nuts, check valve
Price & terms : Please enquire using the email form below.
If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.
We can arrange delivery of equipment and towage of rigs and vessels where needed.
The details mentioned above are believed to be accurate but are not guaranteed.
---------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Hot Oil Truck for Sale
Hot Oilers for Sale
---------------------------------------------------------------------------------------------------------- |