Hydraulic Land Drilling Rig for Sale
New Hydraulic Land Drilling Rig - 1000hp
750hp Hydraulic Land Drilling Rig for sale
1000hp Hydraulic Land Drilling Rig
New Land Drilling Rigs for Sale
Hydraulic Land Drilling Rigs - 750hp - For Sale

Specifications

Mast	Telescopic Mast
Max. hook load	100 tn	200,000 lbs
Stroke length	16.4 m	53.8 ft
Total height incl. substructure	26 m	85 ft
Drilling axis	800 mm	31.5 in

Substructure & Drill floor	Self-erecting	(trailer-based)
Drill floor height	5 m	16.4 ft
Clear height below drill floor	4.1 m	13.5 ft
Rotary opening	698.5 mm	27 ½ in
Drill floor dimensions	10 x 4 m	33 x 13 ft

Hoisting System	Cylinder System
Pulling capacity	100 tn	200,000 lbs
Pull down capacity	22 tn	44,000 lbs
Working clearance to table (under safer sub)	16.4 m	53.8 ft

Top Drive	TDK-32-150-H - hydraulically driven
Load capacity	150 tn	300,000 lbs
Max. drilling torque *	32.000 Nm	23.600 ft-lbs
Max. breaking torque *	38.000 Nm	28,000 ft-lbs
Drilling speed	0 – 177 rpm	0 – 177 rpm
Clamping & breaking device*	100.000 Nm	73.760 ft-lbs
Rated power *	280 kW	375 HP
Pressure stage * nominal value	350 bar	5,000 psi

Engine	Caterpillar C 27 ACERT
Rated power	708 kW	950 HP
Diesel tank capacity	1.700 l	448 gal

Pipe handling system	V-door type (trailer-based)
Max. drill pipe length	Range III	Range III
Max. casing length	Range III	Range III

Transport dimensions rig module
Total weight (excl. truck)	app. 59 t	130,000 lbs
Length (king pin to rear)	12.6 m	41.3 ft
Height (incl. top drive)	4.2 m	13.7 ft
Width	2.5 m	8.2 ft

Mast
The self-standing, telescopic mast consists of two independent sections
with box-type profiles. The outer mast section is connected to the trailer
frame and is equipped with guides for the inner mast section. This sliding
inner mast section is lifted by a central feed cylinder system and allows
lifting and pull-down operations.

Two integrated backstay cylinders raise the mast system into the working
position including crown block and top drive.

The telescopic mast system is designed to handle drill pipes and casings
up to Range III.
No external guy lines are necessary.

Hoisting system
The hoisting system consists of a central, single cylinder with enhanced
buckling resistance. The central cylinder is integrated inside the inner
moving mast section directly below the main rope top sheaves.
The double reeved, twin-wire rope system allows the top drive twice the
lifting stroke and speed of the cylinder. The hoisting system enables lifting
and pull down operations.

Semi-trailer and substructure
The rig frame is directly connected to the five (5) axles semi-trailer. The
semi-trailer is in accordance with standard road regulations and equipped
with a coupling pin according to client’s requirements.

Driller’s cabin
The driller’s cabin is located on the drill floor and offers a high quality
workplace with joystick control. The driller controls all drilling functions
centrally from the ergonomic and air-conditioned cabin. The built-in
instrumentation system provides clear information to the driller at any time.
The system is optionally equipped with a digital data visualization and data
acquisition system.

Transport and set-up
The compact and trailer-based transport units allow a fast and safe moving
and rig-up/down operation and a reduction of transport costs. The compact
footprint of the drilling unit, reduces the costs for wellsite preparation and the
environmental impact.

Substructure and drill floor
The trailer-based substructure is equipped with a selferecting system to lift
the drill floor including driller’s cabin and power tong to the final working
position. The clear height of 4,1m below the drill floor allows sufficient space
for BOP installations.

The compact transport unit including driller’s cabin, power tong, walkways and
handrails allows fast moving operations with high HSE standards.

Pipe handling system
The automated pipe handling system with hands-off technology allows drill pipe
and casing operation without the necessity of a finger board and increases the
personal safety.
For redundancy reasons the pipes can also be handled by using the utility winch
and the V-door ramp.

Top drive
The hydraulically operated top drive TDK 150 H is based on 40 years of
experience in manufacturing rotary heads for drilling rigs. It is designed to meet
advanced performance standards in terms of high drilling torque, high make up
and break out torque, rotation speed, reliability and serviceability.

Additional main components
• Power tong with spinning function 2-7/8” – 8-1/2”
• 2 catheads with 140 kN pulling capacity
• Hydraulic slip lifting device
• Utility winch with 4 tn lifting capacity

Optional equipment and services
• Customized mud handling systems
• Triplex mud pumps
• 24/7 after sales service with worldwide spare and wear part availability
• Remote access and troubleshooting via WAN
• Training Center for customer’s personnel

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

----------------------------------------------------------------------------------------------------------------------------------
Search words -
New Hydraulic Land Drilling Rig for Sale in Europe
Hydraulic Land Drilling Rig - 750hp
Hydraulic Land Drilling Rig - 1000hp - For Sale
New 1000hp Hydraulic Land Drilling Rig
750hp Hydraulic Land Drilling Rig for sale
1000hp Hydraulic Land Drilling Rig for Sale in Europe
Land Drilling Rigs for Sale in Europe
Hydraulic Land Drilling Rig - 750hp - For Sale
New 750HP Hydraulic Land Drilling Rig for sale in Europe
-------------------------------------------------------------------------------------------------------------------------------------