Worldrigs ID: WR674

LCI 750 Drilling Rig for Sale
Carrier Mounted Drilling Rig for Sale
1000 HP drilling rig for sale

Introduction :
The rig is a loadcraft industries 750 drilling rig with mast hook load capacity of 365.000 lbs
(160 metric ton), powered by two caterpillar C15 diesel engines, coupled two allison 6061 RB
transmissions with torque converter. The mast is 114ft (36m) rated at 365.000 lbs API capacity.
Drawworks have 1000hp capacity. All equipment is mounted on a 7 axle carrier. The rig is
equipped with a telescoping substructure at 17ft 6 inches (5.3m) height.
The mast is equipped with a torque arrest beam for the top drive and with piping and necessary
loops to operate the top drive. The total rig is built for extremely quick rig up/down time.
The TD is a northdrill API 250 ton rated with continuous torque rating of 40.500 ft-lbs.
All necessary equipment to operate the top drive in is included with the rig.

1. Carrier
Section 1.1 carrier
- Seven axle heavy-duty carrier for load of 140.000 lbs. Fully equipped with lights and brakes
etc for normal driving operation. All axles have spring brake chambers for safety.
- Tires and wheels are disc wheels, 14"20 all terrain tread. Tire rating of 52.000 psi total.
Two spares delivered.
- Two 100 gallon (2x420 L) fuel tanks side mounted on carrier frame, connected for equalization.
- One toolbox storage box of steel with reinforced lockable doors.
- Eight side platforms with handrails on both sides along the carrier body, four on each side.
Each platform is approx. 6ft x 2 ft (1,8x0,6m)
- One staircase section from side platforms to ground level.
- Hercules 129 HA deadline anchor to be used with compression type weight sensor. Drum type
mounted on carrier frame in front of drawworks frame, hydraulic sensor included.
- Four pedestals to go under front jacks for rig stability.
- Total of six jacks for leveling the rig.

Section 1.2 hydraulic system
- 50 GPM (190 LPM) hydraulic system, design to operate at minimum 2000 psi with rating of
50 gpm at 2100 psi.
- Hydraulic pump driven from PTO on transmission.
- Air activated clutch for pump engagement.
- 325 gallon (1230 L) hydraulic oil tank with filler cap, breather, oil level, oil temp.

Section 1.3 tong circuits
- Tong hydraulic circuit is designed to operate up to 50 gpm at 2000 psi.
- Includes connectors, pressure & return lines, pressure gauge, directional flow valve and pressure
regulating valve.

Section 1.4 handling winch
- Hydraulic powered planetary winch 8000 lb (3.6 t) line pull, rated at 100 ft (30m) per minute at
2000 psi hyd. pressure.
- 325 ft (99m) of 1/2" line on drum
- Fail safe brake (in/out hydraulic activated)
- Winch sheaves provided in crown
- Protection cage on winch
- Controls at operators console

2. Main power/engine
Section 2.1 engine/transmission
-Two caterpillar C-15 540 hp diesel engines
- Equipped with limiting speed governor, air throttle sctuator, lube and fuel filters, alternator and
flywheel housing.
- High ambient radiators and suction fan, permanent type anti-freeze, signel exhaust with spark
arrester diverted to off-operator side with mufflers.
- Engine kill valve located at operators console
- Electric start (remote from operators console)
- Both engines can run at the same time or only one if adequate.

Section 2.2 transmission
- Allison S 6061 RB model six-speed transmission (five fwd 1 rw)
- With converter and oil cooler
- Air over hydraulic controls, with air line indicator system
- Controls available at operators console and in drivers cabin

3. Drawworks
Section 3.1 drawworks
- Model 4212 drum winch assembly
- Full air, fawick "28VC-1000" clutch outside drawworks frame.
- Brakes are 42" (107 cm) diameter x 12" (30,5 cm) wide, lined with 1 inch (2,5 cm) x 12" (30,5 cm)
- API driled brake blocks, full wrap dead-end equalized
- Brake rims are removable with rings for splash water cooling
- Brake operatoin shafts are mounted on ball bearings; these are self engaging and release
by operator.
- Drum barrel is 18" (45,7 cm) in diameter, and 38" (96,5 cm) long, mounted on double row
self-aligning spherical roller bearings on a 6 1/2" (16,5 cm) drum shaft
- Clutch single line pull is 42.500 lb on bare drum and first gear.

Section 3.2 lubrication
- Centralized lubrication system to all bearings and brake linkage on drawworks, is located
outside frame.

Section 3.3 brake water cooling
- Closed loop brake cooling system, mounted on carrier
- Includes 425 gallon tank with covered top, with level indicator
- Removable cap with drain system, breather and fill cap.

Section 3.4 drawworks drive
- ASA-100-3 (1 1/4") pitch, triple stand, roller chain
- Chain drive from input sprocket to sprocket on jackshaft
- ASA-100-3 (1 1/4") pitch, triple stand, roller chain as final drive to main drum

Section 3.5 main drum - grooved jacket
- Lebus counter balanced sleeve is grooved for 1 1/8" wireline, to assist spooling, and reduced line wear.

Section 3.6 hydrotarder
- Parmac 202 hydrodynamic brake assembly with dual rotary
- Fawick 28 VC 1000 air clutch, gates, inlet air valve and piping
- 325 gallon (1230 L) water tank, lines, valves and plumbing installed on rig.
- Drive from the main drum thru triple stand 1 1/4" pitch drive chain.

Section 3.7 combined gearbox
- Cushman model 279 combined gearbox consisting of right angle gearbox and dropbox.
- Right angle gearbox ratio 1:1 to drive single drum drawworks. Dropbox to transfer torque to rotary.
- Pressurized lubrication system.

Section 3.8 sandline drum
- Sandline drum with 42x8 brake size, for handling 16,500 ft of 9/16" wireline on drum
- Brakes are removable for water splash cooling of the brake rims
- Single line pull is 26,000 lbs on the drum

Section 3.9 rotary drive
- Provided at the dropbox for power connection- Elevated chain drive is oil bath type consisting of drive
sprocket at bottom of case with ASA 140-2 (1 3/4") pitch double

4. Mast
Section 4.1 mast
- 114 ft (33,5m) clear working height with an API rated static hook load of 330.000 lb with 8 lines,
and 365.000 lb with 10 lines.
- Designed to withstand 69mph winds from any direction
- Telescoping twin box structure designed and built to API standards.
- Two section with upper section telescoping into lower section for rig move operation.
- Automatic mast latching in raised or lowered position
- Lock and operating control located at base of mast
- Ladder from base to crown with safety blocks for personnel
- All necessary chains, turnbuckles, pins etc included and certified
- 4 inch standpipe rated 5000 lb, welded with 1502 unions.

Section 4.2 crown assembly
- Bender crown arrangement for 8 or 10 lines string up with conventional block.
- One 36" fastline sheave, grooved for 1 1/8"
- One 36" deadline sheave, grooved for 1 1/8"
- Four 30" sheaves cross mounted, grooved for 1 1/8"
- Two catline sheaves
- Crown sheaves are steel with flame hardened grooves.
- Sheaves are mounted on timken tapered roller bearings and all carry certification.
- Crown platform with railing for personnel safety
- Attachment point for four wind guylines from crown to ground is provided.

Section 4.3 tubing board
- All welded construction
- Automatically raised or lowered at mast telescoping
- Mounted at 55 ft above setback
- Board fingers are for 17.000 ft of 2 7/8",  or 11.400 ft of 3 1/2" tubing
- 2 ft 6 inch wide tubing board walkway
- Handrails at board outside
- Attachment points for safety line (escape line) at each corner.

Section 4.4 weight indicator
- Weight indicator complete with sensor
- 12" dial indicator
- Box mount with 25ft of hose assembly
- Calibrated in NM and LBS
- Charts for 6, 8 and 10 lines on indicator

Section 4.5 crown saver
- Load and crown saver installed on drawworks
- Automatically disengages clutch and sets drawwork brakes if block comes too close to crown.

5. Substructure
Section 5.1 hydraulic telescoping substructure
- Working floor height of 17,5 ft (5,3m) with 14 ft in clear under rotary beams
- 4,5 ft is the maximum height when scoped down for transportation
- 10ft 6 in max width when scoped down
- Capacity of 365.000 lbs (160 mt) on rotary beams and 225.000 lbs (100mt) at setback
- Sub base is equipped with fold out wings, total floor area is 18ft wide x 18ft long
- Handrails with toeplate surrounding the entire floor
- One stairway from floor to carrier level
- Pipe ramp with steel plating
- Setback covered with 3" oak timbers
- Two tong backup poles in drilling configuration
- Rat and mousehole access
- BOP handling system with to rails integrated under the floor. Each rail rated at 5 ton.
- Carrier ramp is included with the sub, 10 ft wide to allow the rig to rest completely on the base of
the ramp. Comes in two sections.

Section 5.2 catwalk
- Catwalk assy of 4ft wide x 45 ft long x 3 ft high with built in stair , and bump post.

Section 5.3 hydraulic catworks - make & break-out
- Breakout cylinder has 6ft stroke with 20.000 lb maximum line pull
- Makeup cylinder has 6ft stroke with 20.000 lb maximum line pull
- Cylinder mounted in lower mast section, and includes wireline, turn back sheaves and plumbing
for hydraulics
- Both cylinders are controlled from operators console

6. Top drive
Section 6.1 TD power pack
- One 20ft oilfield skid power pack mounted in a weather and sound protective 30ft container.
- Main motor caterpillar C18 700 hp
- Main HPU at 550kW for TD main power, 2400 L reservoir, two main pumps
- Inline filters for all lines
- Engine driven and electric driven aux hpu for pipehandler functions
- Advanced PLC & HMI system to monitor and control TD system
- All controls integrated at operators console on rig floor
- Quick connectors for all cables and lines on TD system for quick rig up/down

Section 6.2 TD rig equipment
- Mast outfitted with piping for quicker rig up/down with the TD system
- Torque tube beam installed in the mast, and anchored to the mast lower section
- Turnbuckles, chain etc for the torque beam
- Loops from mast to TD (stays in the mast during rig move)

Section 6.3 TD hookup to rig
- The TD power pack connects to the rig by 4 hydraulic hoses that connect on ground level
at the base of the mast
- One 1/4" electrical cable is run up the mast and to the TD for control system
- Five 1/2" electrical cables is run to the operator console for TD operator control
- A power input of 440,160 or 480v to supply the system with electricity
- 1 kW is sufficient to run the system, 40 kW is needed to operate the electrical aux HPU

Section 6.4 TD main specifications
- Continuous torque rating of 40.500 ft-lbs
- Max rpm of 110 in first gear, and 180 in second gear
- Max breakout rating of 43.000 ft-lbs
- Pin connection 6 5/8 RH
- TD is equipped with onboard oil cooler
- Electric over hydraulic onboard valve section for all function control
- Onboard PLC and monitoring equipment

Section 6.5 TD pipehandler specifications
- 360 degrees free traveling orientation
- Backup tong capable of holding up to 80.000 Nm and range from 3 1/2" to 6 5/8" pipe
- Link tilt and retract function for drilling down to floor
- Integrated availability for remote operated elevator
- Upper remote operated IBOP and lower manually operated IBOP rated at 10.00 psi
- Telescopic leg for positioning of backup tong for make or break of saver sub
- Link arms 108 inch
- Manual elevator for 3 1/2" pipe
- Saver sub to 6 5/8 RH and to 5" RH

7. Additional equipment
Section 7.1 handling winch nr.2
- One additional winch equal to above listed handling winch specs

Section 7.2 V-door ramp and pipe racks
- One 48in x 3ft6in x 45ft catwalk from the rig floor level to the 42in high catwalks
- Four 42in x 28ft long pipe racks

Section 7.3 rotary table
- One 22" rotary table, 44" centers complete with split square solid steel master bushing,
spiral bevel gears, precision bearings throughout, removable box cover with lifting eyes,
positive pinion shaft lock and centralized lube system

Section 7.4 high pressure piping
- One 4" 5000 psi mud line and manifold for gauge and kill line, with 1502 union
- 4" 5000 psi standpipe on the lower mast section, with 1502 unions

Section 7.5 crown o'matic
- Combined crown and drawworks type crown-o-matic system for saving mast failures is
installed on the drawworks, and is set for locking the brakes down at activation

Section 7.6 safety chair (board escape)
- One T-bar type escape chair for tubingboard escape

Section 7.7 mast guylines
- Guylines are included, four of 5/8 lines from crown, two from board and two from the mast
mid section. All certified

Section 7.8 block hook
- One of ABCO 250 ton standard hook block
- Clevis kit for use with TD to shorten total assembly length included

Section 7.9 wire rope
- Drill line 1 1/8" wireline rope at 2500 ft, certificates provided
- Drill line spool is included at the front of the carrier by the cab
- 12.000 ft of sandline 9/16" included

Section 7.10 dead line anchor-indicator assy
- Anchor for 1,125" wirerope, for mast pull of 365.000 lbs for 10 lines string up on crown
- Anchor certified, and load cell included

ND 250 H2 (dual ratio)
- Continuous drill torque : 29.800 / 41.000 ft-lbs
- Max breakout torque : 43.000 ft-lbs
- Speed range : 0-200 rpm
- Dual ratio gearbox : Yes
- Gearbox ratio : 1:11.1 / 1:14.9
- Hydraulic motors : 2 x 320 kW max
- System total power rating : 700 hp
- Hydraulic system pressure : 6000 psi / 3000 psi
- Powering engine : C18

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.



----------------------------------------------------------------------------------------------------
Search words(for official use only) :
LCI 750 Drilling Rig for Sale
Used 1000hp Carrier Mounted Drilling rig
1000 HP Drilling Rig for Sale - LCI 750 
1000hp Land Rig Builders
1000hp Land Rig Dealers
Drilling Land Rig for Sale - LCI 750 - 1000 HP
1000HP land Rig For Sale
Carrier Mounted Drilling Rig for Sale
1000 HP Land Drilling Rig For Sale - LCI 750
----------------------------------------------------------------------------------------------------

Worldrigs ID: WR1383

Ingersoll-Rand T4W Drill Rig For Sale
Ingersoll-Rand T4W Drilling Rig - 1981 Built for Sale

Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1981
Condition : Used

Description :

1981 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine
IR 900 CFM / 300 Air Compressor (Inline screw type)
Water Injection Pump
Oil Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Pull Down & 50,000 lbs of Pull Back
18” Table Opening
Hydraulic Cooler
4 & 7 Rod Carousels
4-1/2” x 25ft Used Drill Pipe
3 Outriggers
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Price & terms : Please enquire using the email form below.       

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
1981 Built Ingersoll-Rand T4W Drilling Rig
Ingersoll-Rand T4W Used Drilling Rig for Sale
Used Drilling Rig - Ingersoll-Rand T4W
Ingersoll-Rand Land drilling Rig for Sale
Drilling Rig - Ingersoll-Rand T4W for Sale in USA
-------------------------------------------------------------------------------------------------------

Worldrigs ID: WR346

Used Ideco H37 Rig For sale
Mechanical Drilling Rig - IDECO H37 6500’ For sale

Derrick
National Double Derrick Scope Up (New RAM)
Bottom section 33-1/2 feet > 89 Ft Working room
Top section 56 feet - 91 feet overall

Drawworks
Double drum – IDECO H37
All bearings have been checked, new brake pads
CAT Engine, 550 hp, 0 time – Brand new, with Allison Transmission.
Draw works trailer-mounted 3 New Tandem
Axels – New Brakes and air lines tires steel radials – 20 inch

Substructure
6’6” tall trailer-mounted with cat walk,
12’ sub-structure at rotary table level
Ramp 5 ft tall.
Catwalk & rotary table trailer-mounted
2 axel tandem, new axels, tires and airlines

Mud Pumps
(1)Wilson Snider 6” X 16” Stroke 12893
(2)Wheland 7 1/2” Liners X 14” Stroke p/b
Cummings 350 hp engine,
(3)Gardner Denver FXK 1952 6” X 14” Stroke p/b
CAT 500 hp engine
API Fluid End

Traveling blocks
BJ – 460 ton w/ 6 lines
Swivel – REWSTE 4 Sx

Water Pump
4” X 6” Stroke Gardner Denver
FXG 137 Gallon fuel tank mounted on pump
Skid – Powered by 3 cylinder Detroit diesel
Rotary table, National 12-1/2”

Water Tank
8’W X 8’D X 38-1/2” L – 400 barrel tank

Top Dog House
Double wall insulated 8’ W X 35’ L - 40 all over

Bottom Dog House
7’10” W X 23’10” L

Mud Pit
4’ deep X 7’ W X 40’ L
Generator, CAT powered.

To see more information and pictures, please see
http://www.worldoils.com/landrigs/rig250.php





Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

-------------------------------------------------------------------
Search words(for official use only) :
Land rig - 550hp for sale
550hp Drilling Rig for sale
Ideco H37 Drilling Rig For sale
Ideco H37 for sale
Mechanical Drilling Rig for sale
-------------------------------------------------------------------

Worldrigs ID: WR1098

Ocean Going Tug For Sale
3200HP Ocean Going Tug For Sale
Ocean Going Tug - 36m in length

General Description :

This vessel is to be all welded steel construction with twin engines and twin
fixed pitch propellers inside fixed nozzles. The vessel’s accommodation is to
be located on the main deck and raised (forecastle) deck. The main hull is to
be divided by five (5) transverse WT Bulkheads into the following compartments:

1. Forepeak ballast tank (double as FW tank)
2. FW tank and double bottom FW tank
3. Engine room with double bottom F.O. tank and F.O. side tank
4. F.O. center tanks                 
5. Steering gear compartment and F.O. tank
6. Ballast tanks

Principle Particulars

Main Dimensions
Length Overall : 36.00m
Length WL : 31.70m
Beam Moulded : 10.97m
Depth Moulded : 5.00m
Draft Design : 4.10m

Tank Capacity (approx.)
Freshwater : 100 cubic meter
Fuel oil : 393 cubic meter
Lub.oil : 1.0 cubic meter

Main Engines
2 x Cummins KTA50-M2, 1600BHP/1800rpm
To be joined to gear box WAF 663(Reintjies), ratio 5.95:1

Performance
Free speed : 12knots at sail condition
Bollard Pull : more than 40T at 100% MCR and continuity pulling

Classification
The vessel is to be constructed, machinery and electrical equipments fitted and installed
in accordance with the latest Rules for Shipbuilding of BV Class.
Class notation is : 1 +HULL +MACH, Un-restricted navigation (to be confirmed).

Navigation equipment
1. Two (2) RADAR (IMO approval type)
One Raster-scan X and one X wave band Radar, Power supply AC220V, 6’’ scanners,
10KW emitter, color display units (180mm PPI),range: 0.125~48nm, including :
1 x Scanner
1 x Display
1 x Antenna and radeator
1 x Compass repeater
1 x Handle
1 x 30m
Standard installation material including 30m combination cable
1 x Standard spares
1 x Operation manual
1 x Alternating current rectifier
1 x Radar performance monitor NJU-64J c/w 30m cables & bracket

2. Echo sounder
1 x 6” 3~800m, 200KHz/220VAC
1 x 6” color echo sounder, depth 35~800m, 200KHz/220VAC,including:

1 x  Display/recorder
1 x  Alternating current rectifier
1 x 1.5m Power cable
1 x  30m Cable transducer
1 x Standard spares & installation manual & operation manual

3. Magnetic compass two pieces
One (1) reflector compass, dia. 165mm, stand type, corrector and reflector
are to be fitted in wheelhouse. Lamps are to be fitted on compass for using in night.
Analog signal conversion device and one (1) compass repeated (Signal can be output to radar,
GPS and automatic rudder) are to be supplied for magnetic compass.

Communication equipment (import, JRC or Furuno)
1. GMDSS console
GMDSS console should meet requirements of international rules
for A1 A2 A3 area. For guidance, they are as followings :

a. One (1) SSB radio transceiver, 150w MF/HF, DC 24V,
Frequency range 1.6~27.5 MHz, including :
1 x control unit
1 x antenna and joint
1 x watch keeping receiver
1 x 5m control cable
1 x 5m RF cable
1 x Transceiver
1 x Power supply
1 x Standard spares
1 x Bracket & standard accessories
1 x Operation manual

b. One (1) MF/HF-DSC terminal, DC 24V, including :

c. DSC terminal
1 x 3m DSC Power cable, 1.5m AF cable, 1.5m control cable, control unit.
1 x Standard installation material
1 x Standard accessories including outdoor horn and two (2) 3A standby fuse
1 x 18’ whip antenna, 12’ whip antenna, AC rectifier, battery anto-charger, emergency lamp.

c. One unit Inmarsat-C (marine mobile communication earth station) c/w built-in EGC,
AC 110V and emergency DC 24V, including :
1 x Exterior installation equipment
1 x Interior installation equipment
1 x Antenna with 30m coaxial cable for connection EME to IME
1 x DTE
1 x Keyboard
1 x RO Printer
2 x Distress signal push button
1 x Received signal device
1 x Power supply device
1 x Option switch box
1 x Remote distress signal push button
1 x Standard spares & using installation material
1 x Operation manual

d. GMDSS VHF Telephone (2 Units) :
Semi- amphistyly, DC 24V, including :
1 x Receiver c/w built-in DSC
1 x hand held telephone with foundation
1 x standard installation material ( except antenna)
1 x Operation manual

e. One (1) power supply & charger :
1 x AC power with alternating current-direct current conversion
1 x AC power
1 x Charger

f. One(1) antenna :
4 x Marine VHF antenna
1 x RX antenna
1 x SSB antenna

2. Two (2) handheld VHF radio telephone, including
1 x handheld receiver with fixed antenna
1 x lithium battery seating
1 x Operation manual

3. Tow (2) GMDSS radar transponder, each one should include
1 x lithium battery
1 x seating and standard accessories
1 x operation manual

4. One (1) GMDSS Communication station
Which design suitable for easy operate, install and maintain.
Operation panel using for MF/HF radio device and C-station terminal should be fitted on the same console.
Emergency lamp & emergency light

5. One (1) GMDSS EPIRB, including
1 x ACR EPIRB  406MHz, Type RLB-32 (2774)
1 x lithium battery
1 x water power release gear
1 x standard accessories & operation manual

6. One (1) weather fax receiver, including
1 x recorder
1 x Pre-AMP fax - 5 with 2.6m plait
1 x DC AC rectifier
1 x standard accessories
1 x 15m coaxial cable
1 x AC converter

7. One (1) navtex receiver, including
1 x JRC navtex receiver, type NCR-330, AC 12/24V
1 x transmitting antenna
1 x 40m 7ZPJD0044  thermographic paper
2 x 6ZXAF00021 standby fuse
1 x standard material include 20m cable
1 x standard accessories
1 x operation manual

8. One (1) AIS
1 x Display
1 x GPS antenna
1 x Shakespeare type antenna
1 x junction box
1 x standard accessories
1 x Standard installation material include 15m antenna cable
1 x standard spares
1 x operation manual

Accommodation
2×Single Cabin : 2men
2×2-Men Cabin : 4men
2×4-Men Cabin : 8men
Total : 14men

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------
Search words(for official use only) -
Ocean Going Tug for sale
3200 HP Ocean Going Tug - For Sale
Tugs For Sale
36m long - Used Tug - For Sale
Used 3200 HP Ocean Going Tugs for Sale
Ocean Going Tug For Sale - 36m in length
-------------------------------------------------------------------------------

Worldrigs ID: WR2080

45M Anchor Handling Tug - For Sale
Used AHT for Sale
70TBP Anchor Handling Tug for Sale

General
Year Built : 2009
Class : Bureau Veritas
Notation :
I HULL MACH, Tug; Special Service- Anchor
Handling Vessel Unrestricted Navigation

GRT / NRT : 874/262
Deadweight : 539 MT

Dimensions
Length Overall : 45.00 m
Length Waterline : 43.50 m
Breadth Moulded : 12.60 m
Depth Moulded : 5.30 m
Draft (max) : 4.50 m

Performance
Maximum Speed : 13.0 knots at 15 MT/24 hrs
Economical Speed : 10.0 knots at 10 MT/24 hrs
Type of Fuel : Marine Gas Oil
Endurance : About 40 days

Cargo Capacities
Fuel Oil : 486 m³
DW/SWB : 77 m³
Fresh Water : 266 m³
Freezer/Chiller : 30m³
Deck Cargo : 100 MT
Deck Strength : Uniform 5 T/m² main deck & 15 T/m² stern
Clear Deck Area : 200 m²

Navigational and Communication Equipment
GMDSS (For Area 3) : 1 x Furuno RC-1800 IT
SSB : 1 x Furuno FS 2570C
VHF : 2 x Furuno FS 8800S/ Icom IC-M422
Radar : 1 x Furuno FAR 2117/ 1942 Mark 2
Echo Sounder : 1 x JRC Model JFC-582-200 Khz
Gyro Compass : 1 x unit at main steering position at sterring gear
Magnetic Compass : 1 x unit standart suara model MR-150
Speed Log : 1 Doppler log JRC Model JLN -205
Auto Pilot : 1 unit Syncronized to gyro steering compass
Navtex Receiver : 1 x Furuno NX 700
GPS Navigator : 2 x Furuno GP-150
AIS : 1 x Furuno FA-150
SART : 2 x Mcmurdo S4
EPIRB : 1 x Mcmurdo E5
Portable VHF (GMDSS) : 3 x Jotron TR20

Deck Equipment
Anchor Windlass c/w bow : 1 x electro-hydraulic 24 MT
Anchors & Chain :
2 x Stockless Anchor 1160 kg each;
2 x 605m x 34mm Ø U2 Stud Link Chains

Anchor Handling / Tugger Winch :
1 x electro hydraulic; double drum waterfall type
Line Pull at 1st Layer :
150T @ 6m/min (1st speed)
75T @ 12m/min (2nd speed)
12T @ 36m/min (2nd speed)

Brake Holding : 225 MT at 1st layer
Drum Capacity : 1000m (L) x 58 mm (Dia) SWR
Bollard Pull : 70.06 T
Tugger Winch : 2 x electro hydraulic 10T@ 15 m/min
Capstan : 2 x electro hydraulic 5T@ 15 m/min
Towing Pin : 2 x SWL 100 T
Shark Jaw : 1 x SWL 200 T
Stern Roller : 1 x 1500mm Ø x 4200 mm width – SWL 200T

Life Saving Equipment
Life Rafts : 1x25 men & 1x20 men, SOLAS compliant
Rescue Boat c/w Davit :
1 x 6 men, 20HP c/w outboard engine,
SOLAS compliant
All other life saving appliances as per SOLAS requirements

Propulsion System
Main Engines :
2 x Niigata 6MG28HX, 2500 BHP/ 1823 KW
Total: 5000 BHP/ 3646 KW

Auxiliary Engines : 3 x 300 KW - 415V, 3PH, 50HZ
Emergency Generator : 1 x 80 KW - 415V, 3PH, 50 HZ
Bow Thruster : 1 x 441 KW
Propellers : 2 x FPP
Steering Gear System : 2 x Electro Hydraulic
Rudder : 2

Fire-Fighting Equipment / Anti-Pollution Equipment
External
Equivalent to 1/2 FiFi
Fire pump : 1 x 1500 m³/hr @140m head

Internal
CO² System : Engine Room
Fire Fighting Equipment : Fully compliant with SOLAS requirements
Emergency Fire Pump : 1 x 30 m³/hr @ 60m head
Water Mist System : Engine Room

Accommodation (All cabins are fully air-conditioned)
Berths :
4 x 1 berth cabins = 4
2 x 2 berth cabins = 4
4 x 4 berth cabins = 16
Total : 24

Dispersant System
Fresh Water Maker : Nil
Oily Water Separator : 1 x 1.2 m³/hr
Sewage Treatment Plant : 5.5 m³/hr

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
-------------------------------------------------------------
Search words (for official use only) -
45M AHT for Sale
Used 45M AHT for Sale
Anchor Handling Tug for Sale
2009 built AHT for Sale
45M Anchor Handling Tug - For Sale
Used AHT for Sale
70TBP Anchor Handling Tug for Sale
2009 built Used AHT for Sale
---------------------------------------------------------------

Worldrigs ID: WR2745

Geoprobe 8150LS Crawler Drilling Rig for Sale
Geoprobe 8150LS Crawler Drilling Rig - 2017 Built for Sale

Model : 8150LS Crawler Drill Rig
Manufacturer : Geoprobe
Year : 2017
Condition : Used

Description :

Geoprobe 8150LS Crawler Drill Rig
Geoprobe 50DT Track Base Platform
Geoprobe GV5 Sonic Head Long Stroke
Geoprobe Designed Rod Handling
System Head Feed Stroke: 157"
50K Dynamic Force
Remote Diagnostics
Adjustable Swing-arm Control Panel
Automatic Drop Hammer 140 lb
Winch Kit: 2,500 lb

Safety Cage
Triplex High Pressure Water Pump
Air Compressor Kit, C6.6 with BA-922
Drop Rack System with Rod Rack
Drill Mast Side-Shift
Head Centerline Side-Shift
Fits in 40 ft Shipping Container for Exporting
10-ft Tooling Compatible
Rock Coring Compatible
14" in Double Wrench Breakout
Dual Winch System
Front and Rear Outriggers (Four Point Stabilization)
Two tooling indexing racks with rollers
230 ft of 4 tooling
230 ft of 6” tooling
100 ft of 8” tooling
One Actuator core for rod handler
One SDT-60 Weighted Wire Line Core Barrel
Several bits and adapters
(Cost Extra or included as a package for all listed together)
2010 Freightliner model Cascadia Truck with Diesel Engine (492,560 miles)
Trailer for the hauling the drill, pipe, and tooling (as is in the pictures)
1210 Hours on Engine, 210 Hours on Sonic Head at time of listing.
(Price Reduced as of 7/2020 to sell fast)

Location : USA

Price & terms : Please enquire using the email form below.        

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
2017 Built Geoprobe 8150LS Crawler Drilling Rig for Sale
Drilling Rig - Geoprobe 8150LS - For Sale
Geoprobe 8150LS Crawler Used Drilling Rig for Sale
Used Geoprobe 8150LS Crawler Drilling Rig for Sale in USA
Geoprobe Crawler Drilling Rig for Sale in USA
-------------------------------------------------------------------------------------------------------

Worldrigs ID: WR611

Anchor Handling Vessel For Sale
4000bhp Anchor Handling Vessel For Sale
50M AHT For Sale

Principle Particulars
Length O.A. overall (Mld hull) : 49.95 m
Length W.L. : 48.60 m
Breadth moulded : 12.60 m
Depth moulded : 5.75 m
Draft moulded (design) : 4.50 m

Capacities
Clear Cargo Deck aft : 220 m2 (22 x 10)
Deadweight approx. : 700 t (at max. draft of 4.8m)
Tank Capacities With tanks 100% full, the approx. capacities will be as follows:
Portable, total : 242 M3 (approx)
Fuel Oil, total : 500 M3 (approx)
L.O. Storage (M.E) : 2 x 6 M3 (approx)
L.O Storage (Gensets) : 2 M3 (approx)
Hyd. Oil : 2 x 5 M3 (approx)
Steering Gear Oil : 1 M3 (approx)
Freezer/Chiller (Ship's use) : 2 x 5 M3 (approx)
Bilge Holding Tank : 5 M3 (approx)
Sewage Holding Tank : 5 M3 (approx)
Dirty Oil Tank : 5 M3 (approx)
Foam : 16 M3 (approx)
Dispersant : 19 M3 (approx)

Complement and Accommodation
3 x 4-berth cabin : 12 men
6 x 2-berth cabins : 12 men
3 x 1-berth cabins : 3 men
Total Complement : 27 men

Main Engines
Main engines to be two (2) Cummins QSK 60, each developing an MCR of 2200 BHP at
1800 RPM, giving a total of about 4400 BHP Continuous power.

Geberators - Main
Two (2) marine diesel generating sets, heat exchanger cooled, each rated approx 250
KW, 415V, 3 Phase, 50 Hz, 0.8 P.F.. The two units are to be able to operate in parallel.
Basic Design Characteristics:-
- Heat exchanger cooled
- 4 strokes
- Engine mounted L.O, fresh water, fuel oil and raw water pumps
- Engine mounted L.O. and fresh water coolers
- Local and remote start
- Resilient mounting
- Auto synchronizing

Life Saving Equipment
Life saving equipment is to be in accordance with Classification and Solas requirements
for an Ocean Going Vessel with a total complement of thirty (30) men.
The Life saving equipment shall include at least the following:-
Liferafts : Four (4) inflatable liferafts to SOLAS requirement, each certified for
twenty (20) men are to be stowed in hinged type cradles for quick sideway launching. All
to be SOLAS Approved.
Lifebuoys : Eight (8) lifebuoys of PVC or equal approved construction. Four (4)
lifebuoys with 90-Ft buoyancy line Four (4) lifebuoys with 90-Ft buoyancy line and selfigniting
electric lights Two (2) smoke signals of the latter). All to be SOLAS approved.
One (1) lifebuoy to be positioned close to stern.
Lifejackets : Thirty-eight (38) approved type lifejackets to be supplied and stowed
adjacent to each berth. Including 2 Spare jackets. All to be SOLAS approved.
Pyrotechnics : Twelve- (12) parachute distress rockets. Two (2) orange smoke
signals each to have 120 seconds discharge time and be waterproof.
Rescue Boat : One (1) Solas approved type rigid 6-men rescue Boat c/w 25BHP
outboard engine and approved gravity type davit is to be provided
Line Throwing : One (1) set Line Throwing Apparatus to meet with SOLAS
requirement.
Retro Reflective : Life Saving appliances are to be fitted with reflective tapes .
Boat Hooks : Two (2) boat hooks c/w approx. 8mm handle.
First Aid Kit : As per rules.

Firefighting Equipment
Internal firefighting
Firefighting equipment is to meet Classification and relevant Flag state Regulations.
Generally all in accordance with the following:
Firemain:-
A firemain and hydrants are to be installed, six (6) on various deck levels and two in
engine room. 10M canvas fire hose c/w brass coupling and nozzle is to be supplied and
stowed alongside each hydrant in a protective box. All nozzles to be dual jet/spay type.
International shore connection is to be fitted.
Fireman's Outfit:-
Two (2) complete sets (each contained in its own separate storage unit) of fireman's outfit
are to be provided, comprising the following:-
-one (1) protective clothing
-one( 1) breathing apparatus
- oxygen tank and mask
-one( 1) fireman's axe
-one( 1) safety lamp of portable battery type
-one( 1) set of gloves and boots

External Firefighting
The following equipment are to be fitted for the vessel to comply with half Fi Fi
standards with water spray curtain.
a) Fire Pump
Two (2) unit seawater pump, one 1700 M3/Hr drive by main engine , other one 1200
M3/H drive by independent engine at 14 kg/cm2 to supply the fire monitor.
b) Fire Monitor Two (2) units monitor at 1200 m3/hr each (Foam/ Water) Remote
controlled.

Navigation and Communications Equipment
One (1) unit of DSC watch keeping receiver.
Two (2) units of search and rescue radar transponder (SART)
One (1) Inmarsat “C” station with voice, fax, email facility.
One (1) unit of NAVTEX Receiver
One (1) EPIRB
One (1) MF/HF SSB
Two (2) Radars, both X-band, meeting SOLAS & GMDSS, both Furuno 1510 with
ARPA function
One (1) speed log system comprising transducer receiver, inter-phasing facility and 
interconnecting cable shall be provided and installed.
One (1) master gyro-compass fitted with five (5) gyro repeaters positioned as follows :-
One (1) centrally located in wheelhouse forward steering station as steering compass
One (1) centrally located in wheelhouse aft steering station
Two (2) outside of wheelhouse positioned clear of obstructions so as to allow bearings to
be taken, fitted with azimuthing ring capable of obtaining compass errors.
One (1) auto pilot compatible and interfaced with gyro and steering compass.
One (1) magnetic compass, 7 inch reflector type c/w correction magnet, quadrant balls
and reflector tube and compass binnacle, Azimuth device.
One (1) DGPS (Global Positioning System) navigator.
One (1) echo-sounder, 0-036 ft deep range c/w repeater at aft manoeuvring station.
Three (3) sets walkie talkie, intrinsically safe, complete with spare battery and chargers.
SSB set (See separate clause).
Item not specified above but required by the relevant Authority are to be supplied by
owner

Anchor Handling Fork, Shark Jaw
One (1) set electro-hydraulically operated anchor handling fork (hydraulic retractable
shark jaws) of approved make to be installed in centreline on main deck aft. The stopper
to be able to take 2” to 3” dia. Wire and 1-1/4” to 3” dia. Chain.
SWL to be 200 tonnes. Stopper to have separate hydraulic power unit and to be remotely
controlled from the cargo rail on main deck aft and from wheelhouse aft.

Towing Pins (200t SWL)
Two (2) vertical hydraulic towing pins of approved make, retractable type, closed top to
be installed in the centreline of the main deck. The anchor handling pins to extend about
600mm above main decklevel in the fully extended position. The pins are to be operable
from wheelhouse aft and locally.

Capstans
Two (2) electro- hydraulic/hydraulic capstans each of 5 tonnes at 15m/min capacity to be
installed aft as shown on the General arrangement drawing light load speed to be
30m/min. Local controls.

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

-----------------------------------------------------------------------------------------------------------------------------
Search words(for official use only) - 
Anchor Handling Vessel For Sale
4400bhp AHT For Sale
AHT For Sale in Middle East, Dubai
4000bhp Anchor Handling Vessel For Sale
4000bhp Anchor Handling Tug in Singapore, Malaysia, Indonesia
4000 bhp AHT For Sale
AHT For Sale
AHT For Sale in Singapore, Malaysia, Indonesia
------------------------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1252

Reedrill SKT Drilling Rig for Sale
Reedrill Drilling Rig - 2001 Built for Sale

Model : SKT Drill Rig
Manufacturer : Reedrill
Year : 2001
Condition : Used

Description :

2001 Reedrill SKT Drill Rig
Total frame hours 7700
CAT 3408 diesel engine (525 HP with 3000 hours)
Sullair 990 cfm / 350 psi air compressor with 1000 hours
Auto-lube
Thread greaser
Dust collector
Fire suppression
Winch
Cold weather equipment
HOBO wrench
Set up for 4-1/2" x 30ft steel
Comes with pipe and hammer
hydraulic leveling jacks
Mounted on Carrier with metal tracks

Location : USA

Price & terms : Please enquire using the email form below.       

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
2001 Built Reedrill SKT Drilling Rig for Sale
Used Reedrill Drilling Rig for Sale
Reedrill Used Drilling Rig  for Sale in USA
Drilling Rig - Reedrill SKT for Sale
Used Drilling Rig for Sale in USA
---------------------------------------------------------------------------------------------------------

 

Worldrigs ID: WR2902

44 Ton Vryhof anchor for Sale

Worldrigs ID: WR1420

Chicago Pneumatic 670 Drilling Rig - For sale
Chicago Pneumatic Used Drilling Rig for Sale

Model : 670 Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1972
Condition : Used

Description :

1972 Chicago Pneumatic 670 Drill Rig
International 510 gas engine (barley runs)
5-speed transmission
CAT 3406 diesel engine
GHH 750 cfm / 300 psi air compressor
Jib & carousel

Includes as a package:
8 inches hammer w/ 8 inches bit
6 inches hammer w/ 6-¼ inches bit
Jib & carousel
800 ft of 4 inches x 20 ft drill pipe

Location : USA

Price & terms : Please enquire using the email form below.       

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Chicago Pneumatic - 1972 built - For Sale
Used Drilling Rig Chicago Pneumatic for sale
Drilling Rig Chicago Pneumatic 670 for sale
Chicago Pneumatic Land Drilling Rig For Sale
Used Chicago Pneumatic Drilling Rig for sale in USA
---------------------------------------------------------------------------------------------------------

 

Worldrigs ID: WR2872

30,000 LPG Propane Tank - 1973 Built - for Sale
Propane LPG Tanks for Sale

Description :

Built : 1973
ASME certified
250 PSI
Dimensions : 109"DIA x 67ft OAL Approx.

Price & terms : Please enquire using the email form below.        

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
1973 Built LPG Propane Tanks for Sale
30,000 Gallon Capacity LPG Tank for Sale
Used Propane LPG Tanks for Sale
Propane Storage Tanks for Sale
LPG Propane Tanks - 30,000 Gallon - For Sale
--------------------------------------------------------------------------------------------------------

Worldrigs ID: WR961

Housing for North Dakota
Temporary Homes for North Dakotaa
Mobile Homes for Bakken Shale Plate & North Dakota
Temporary homes for North Dakota
Portable Homes For Bakken Shale Plate

50 Proposed Homes for Sale

Description :

The units are thermal zone III and wind zone III meaning that they are intended for cold
climate and high sustained wind activity in excess of 110 mph.  The units include all
appliances, furniture and HVAC (heat with air conditioning).

These units do not require escorts as they are 12’ wide.  The units utilize 10” frame
rails as part of the ruggedized construction.  They also have fire extinguishers, smoke
detectors and carbon monoxide detectors.  These units also include NOAA weather
radios that will alarm prior to the arrival of dangerous wind storms. 

Currently there are 47 of these units available for immediate delivery with an additional
25 units being completed on the factory line.

Standard Undercarriage   
SW1240 - 10" I-Beam - 40' w/ 4' Hitch   
(4 on 40') to insure protection   
on delivery / transportation, set up   
and site conditions and longevity due to    
any inconsistancies resulting from those very   
key issues.  All axles and tires are new.   
2 Brake - 2 Idler Axles

Floor System   
2” x 6” Floor joist #2 SPF or better   
16” O.C.    
23/32 Tongue & Groove OSB Floor Decking   
Metal heat ducts wrapped with R-4 insulation   

Carpet / Roll Goods 
Linoleum Throughout 

Wall Construction   
2” x 6” #2 SPF exterior wall studs – 16” OC   
2” x 6” top plate over windows and door headers   
90" sidewall flat ceiling   

Electrical   
200 AMP electrical service  
Bard Wall Unit 10KW Heat Strip  
34,000 BTU to supply ceiling heat duct  
1-Ext. GFI weatherproof recept  
Lighted bath exhaust fan  
Wire and vent for dryer  
Smoke detectors with strobe  
Electrical Wiring per 2005 NEC

Plumbing    
30 gallon double-element electric water heater    
Main supply water shutoff    
Brass plumbing tees and elbows    
TuffPEXÔ polyethylene non-toxic tubing vs rigid waterline    
Pressure rated pex to 200 deg. F @ 80 psi    
1-pc. 60” tub/shower fiberglass    
Plumbing for washer – Wire for dryer    
Water Shut off’s throughout    

Insulation  
R-22 batt ceiling insulation - wool  
R-19 batt sidewall insulation  
R-19 batt floor insulation  

Roof Construction    
30 lb. Roof load trusses    
Nominal 3/12 Roof pitch - 16" O.C. Trusses    
7/16” OSB roof decking    
Owens Corning Supreme Shingles - Shasta White    
Ice and water shield at eaves    
    
Windows  
Kinro Wind Zone III Windows  
Low-E insulated glass  
Removable screens-all windows  

Interior    
2.7 Mil Azdale wall panel    
Residential finished ceiling Sea-Spray with vapor barrier    
Childproof shades on windows    
Prehung white interior doors    
Mortise hinged int. doors     
Wood trim, doors and windows    
3 hinges per door    
China commodes in all baths     
Plastic sink - baths    
Ceiling mount heat registers    

Furniture   
Dinette table w/ 4 chairs   
Living Room sofa with pull out bed   
Bedrooms std mattress w/box spring, frame and five drawer dresser   
Weather radio

Kitchen / Baths    
Banak cabinets    
Flat Panel Doors    
Shelves overhead cabinets    
Cabinet door hinges    
33” x 22” x 6” deep bowl(s) stainless steel sink – Kitchen    
White power vent and lighted range hood    
GE 18CF FF Refrigerator    
GE 30" Electric Range    

Exterior Doors    
36” x 76” Vinyl clad steel insulated 6-panel frt dr outswing    
36” x 76” Vinyl clad steel insulated 6-panel rear dr outswing    
Deadbolt lock-front and rear     

Exterior   
Crane 4”ä Dutch Profile- vinyl siding with matching crown molding   
40 mil thick virgin vinyl material - no regrind

Price & terms : Please enquire using the email form below.

Worldrigs ID: WR494

Mini Bulker for sale
4500T Mini Bulker for sale
Used Mini Bulker for sale
1984 built Mini Bulker - For Sale
Cheap Small Bulk Carrier For Sale

General Information
Type of vessel : Bulk Carrier
Built : 1984
Classification : VIRES

Main Particulars
LOA : 94.86 m
LBP : 88.00 m
Breadth mounded : 15.80 m
Draft (in Summer) : 5.50 m
Light draft :
Fore : 1.67 m
Aft : 2.07 m

GRT : 2,826
NRT : 1,283
DWT : 4,485
M/E :
6EL40

BHP : 3,300 CV
RPM: 130
Cargo Gear : - Derricks : 3 Units x 15 Mts
Service Speed :
Full Loaded : 12.3 knots
In Ballast : 15.1 knots

Hold’s Dimensions
Hold No.1 : 25.2m x 15.6m x 5.6m
Hold No.2 : 37.8m x 15.6m x 5.6m

Cargo Hatches
Hold No.1 : 14.7m x 8.2m
Hold No.2 : 27.3m x 8.2m

The service capacities of bunker and fresh water :
FW / DO / FO : 390.7 / 37.4 / 331.6 mts

Daily Consumption
Main Engine : 8.0 mts FO/day

Generators
Power : 300 CV - 1.200 RPM x 2 units
Cargo Working : 1.2 Ts DO/day
At Sea : 0.6 Ts DO/day
Idle : 0.7 Ts DO/day

Ventilation System : Natural
Cargo batten fitted : NIL
Type of Hatches’ cover : Pontoon

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

-------------------------------------------------------------------------------------
Search words(for official use only) -  
Mini Bulker for Sale
4500T Mini Bulker for sale
Cheap Small Bulk Carrier For Sale
95M Mini Bulker for sale
1984 built Mini Bulker - For Sale
Cheap Mini Bulker for sale
Bulk Carrier For Sale - 95M
5000Ton dwt Bulk Carrier for sale
Cheap Used Small Bulk Carrier For Sale
4000Ton Dwt Bulk Carrier For Sale
---------------------------------------------------------------------------------------

Worldrigs ID: WR424

Anchor Handling Tug for sale
2009 Built 40m 5000 BHP Anchor Handling Tug
AHT For Sale - 5000bhp
5000BHP Anchor Handling Tug For Sale

Principal Particulars
Classification : Bureau Veritas
Year Built : 2009

Length Overall : 40.00m
Length B.P. : 36.46m
Breadth Moulded : 11.80m
Depth Moulded : 4.60m
Summer Draft : 4.000m

Capacities
Gross Tonnage : 480 tons
Net Tonnage : 144 tons
Load Displacements :
Fuel Capacity : 425cbm
Fresh Water : 100cbm
Speed : 13.7 knots

Range
Bollard Pull : 62 Tonnes @100% MCR
Fuel Consumption :
8.850 litres/day (Max Speed)
7.920 litres/day (Cruising Speed)
Accommodation : 22 persons
LSA Certificate : 22 persons

Machinery & Equipment
Main Engines :
2 x NIIGATA 6MG28HX (1118.75KVA/1838Kw/2500BHP each at 750 rpm)
Generators :
2 x Cummins 6BT (100KVA/265KW/107.28BHPeach at1500rpm,3 ph,415V)
Gearboxes : Twin Disc (6: 1)
Propellers : 2 x 4-Blades Kaplan
Towing Winch : 40 Tons Break Holding
Towing Wire : 40mm diameter 800m long

Fire/Salvage Pumps : 60 m3/hrs + portable pumps
Fire Monitors : Nil
Foam Tank : Nil
Navigational Aids & Communications :
1 Radar, 1 AIS, 1 SART, 1 GPS, 1 SSB, 2 VHF, 1 EPIRB, 1 Walkie Talkie

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------
Search words(for official use only) -
Anchor Handling Tug for sale
AHT of 5000BHP for Sale
5000bhp 40m AHT for sale
AHT for Sale in Singapore
AHT for Sale in Malaysia
5000bhp 40m AHT for sale
AHT for Sale in Asia
5000bhp Anchor Handling Tug For Sale
--------------------------------------------------------------------------------------------------

Worldrigs ID: WR2882

Worldrigs ID: WR537

Atlas Copco Used Air Compressors For Sale
1993 Atlas Copco XP1400WCU & XASE 1600

Model : XP1400WCU & XASE 1600
Manufacturer : Atlas Copco
Year : 1993
Condition : Used

Description
(1) Ingersoll-Rand 1400 and (1) Atlas Copco XASE 1600 Air Compressors on (1) 40' ft Skid
(1) 1993 Ingersoll-Rand XP1400WCU Air Compressor
1600 CFM at 125 PSI
S/N 219991UJC38
Recon Cummins 855 Diesel Engine
4000 Hours Since Rebuilt
5,307.6 hours

(1) Atlas Copco XASE 1600 Air Compressor
1600 CFM at 125 PSI
Detroit 8V92T Diesel Engine
Hours 4,780.2
Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------------------
Search words(for official use only) - 
Atlas Copco Used Air Compressors for Sale
Atlas Copco XP1400WCU & XASE 1600 
1993 Atlas Copco Mining Equipment for Sale
Atlas Copco XASE 1600 Air Compressors
Mining Equipment Air Compressors  for Sale in USA
--------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2635

LTI 1000KP Drilling Rig
Drilling Rig - LTI 1000KP 2000Hp - For Sale

Description :

General Description :
Make : Lee C Moore
Estimated Drilling Depth : 20,000ft
Estimated Rig Move Loads : 75
Estimated Camp Move Loads : 20
Rated HP : 2000

Mast :
Height : 147.00ft
Static Hook Load Capacity : 1,000,000lb
Mast Racking Capacity : 20,800ft

Substructure :
Style : Parallelogram
Height : 30.00 ft
Clear Height : 25.25 ft
Casing Capacity : 1,000,000lb
Maximum Setback Load : 600,00lbs

Drawworks :
Make : LeTourneau                                                                    
Model : LDW 1000k
Power Rating :2000hp
Marine Inc
TT 1500
Drilling Line Size : 1½"
Brake Type - Band or Disk : Disk

Top Drive / Power Swivel :
No Top Drive

Swivel :
No Swivel

Rotary Table :
Table Opening : 37 ½"
Maximum Load Rating : 650 Ton

Power Generation :
No Engines
No Generators                                             
SCR / VFD / DC /DC : VFD Rig

Mud System :
WH 1612                                          
@ 120 spm                                         
Pressure Rating : 7,500 psi                                   
Active Mud Volume : 590 bbls
Reserve Mud Volume : 460bbls                                                                             
Process Ltd.                     
Mud Cleaner : N /A
Desander : N /A
Desilter : N /A
Centrifuge : N /A

Well Control :
Shaffer                                                 
10,000 psi,
Cameron                                
Controls
8 stations
3,000 psi

Enhancements :
Tools 26-100PD

Location : Australia

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

------------------------------------------------------------------------------------
Search words (for official use only) :          
2000Hp LTI 1000KP Drilling Rig for Sale
20,000 ft Drilling Depth Land Drilling Rig for Sale
Land Drilling Rig - 2000 HP - For Sale
LTI 1000KP Used Drilling Rig for Sale
LTI 1000KP Drilling Rig - 2000Hp for Sale in Australia
-----------------------------------------------------------------------------------

Worldrigs ID: WR2939

Schramm TXD 200 Trailer Mounted Drilling Rig for Sale
Drilling Rig - Schramm TXD200 - For Sale

Description :

2011 Model Schramm TXD200 Unit 139 Ser# J135-0204 Rig Trailer 2011
Kimble Vin 1K9AD40C8B3268121
MTU 12V2000
Sub Base/Mud Boat 1 Piece
Tag Azle 2011 Model Kimble Vin 1K9AL10A7B3268126
Pipe Loader/Loadsafe 2007 Model Unit 6006 Vin 1K9AH54B172268003
Doghouse/Water Tank/Tool Room Unit 7166 2011 22.5 Ton 53ft x 10ft Vin/Ser
1D9SD5323B1664027
4.5" Drill Pipe Slips
6" Drill Collar Slips
8" Drill Collar Slips
A Few Misc Fittings

Location : USA

Price & terms : Please enquire using the email form below.        

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Schramm TXD200 Drilling Rig for Sale
Schramm TXD200 Drilling Rig - 2011 Built for Sale
2011 Built Schramm TXD200 Drilling Rig for Sale
Used Schramm TXD200 Drilling Rig for Sale
Schramm TXD200 Drilling Rig for Sale in USA
-------------------------------------------------------------------------------------------------------

Worldrigs ID: WR360

Log Cabins For Canada
Log Home Builders
Log Houses in Canada
Quick Build Log Homes

Full solutions provided inclusing furnishings, catering,
water treatment. hotel management etc.

Cedar panel interior walls 
Cedar exterior.

We have various sizes and designs for housing in USA.

Log Housing For Canada
Log Housing For America

Price & terms : Please enquire using the email form below.

If you cannot find the housing that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

Full Turnkey solutions provided.
--------------------------------------------------------------------
Search words (for official use only) -
Housing For Canada
Homes For Canada
Log Housing for Canada
Log Homes For Canada
Quick Log Homes
Log House Builders in USA
Cheap Housing for Canada
Cheap Housing for USA
Log Houses in America
Log Home Builders in America
Log Home Builders in Canada
Quick Building Log Houses
----------------------------------------------------------------------

Worldrigs ID: WR2631

Chicago Pneumatic 670 Drilling Rig for Sale
1976 Built Chicago Pneumatic 670 Drilling Rig for Sale

Model : 670 Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1976
Condition : Used

Description :

1976 Chicago Pneumatic 670 Drill Rig
CAT 3406 Diesel Deck Engine
800 cfm / 200 psi Screw type Air Compressor
Mounted on a 1976 GMC 7500 Truck
Detroit V6 Diesel Engine
Note: Tower is Broken & Jack Cylinders Need Rebuilt

Location : USA

Price & terms : Please enquire using the email form below.        

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Drilling Rig - Chicago Pneumatic 670 - For Sale
Chicago Pneumatic 670 Drilling Rig - 1976 Built for Sale
Used Chicago Pneumatic 670 Drilling Rig for Sale
Chicago Pneumatic Used Land Drilling Rig for Sale
Chicago Pneumatic 670 Drilling Rig for Sale in USA
-------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2559

Soilmec SR30 Drilling Rig for Sale
Soilmec SR30 Drilling Rig - 2017 Built for Sale

Model : SR30 Drill Rig
Manufacturer : Soilmec
Year : 2017
Condition : Used

Description :

2017 Soilmec SR30 Drill Rig
Hours: 1000 (as of Oct 2018)
Cummins QSB6.7-T4F Diesel Engine

Location : Europe

Price & terms : Please enquire using the email form below.       

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
2017 Built Soilmec SR30 Drilling Rig for Sale
Used Soilmec SR30 Drilling Rig for Sale
New Soilmec  Drilling Rig for Sale
Drilling Rig - Soilmec SR30 for Sale
2017 Built Land Drilling Rig for Sale
---------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2219

3 Pax Superyacht  Submersible for Sale
3.2M Superyacht  Submersible for sale

Description
The Superyacht submersible is the world’s lightest and most compact
three passenger production submersible.  The 1650/3 LP will take a pilot
and two passengers to 500 meters (1,650 feet) in total comfort.

Specifications
General -
Depth : 1,639ft / 500m
Payload : 1,210lb / 550kg
Crew : Pilot + 2 Pax
Speed : 3kts
Endurance : 12 hours
Main Ballast : 4,840lb / 2,200kg
Variable Ballast : 220lb / 100kg

Size and Weight
Length : 10.5ft / 3.2m
Width : 8.7ft / 2.6m
Height : 5.9ft / 1.8m
Weight : 8,800lbs / 4,000kg
Pressure Hull Inner ø : 60in / 1,525mm
Pressure Hull Outer ø : 3.3in / 85mm
Hatch Inner ø : 23.6in / 600mm

Systems
24v Supply : Dual Supply + Emergency
Main Battery : 30 kWh
Main Thrusters : 2x5hp / 2x3.7kW
Vertran Thrusters : 2x5hp / 2x3.7kW
Control : Joystick, Touch Screen + Manual Override
External Lights : 5 x 20,000 lumen LED
Life Support : Oxygen & CO2 Scrubber

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
3 Pax Superyacht  Submersible for Sale
3.2M Superyacht  Submersible for sale
500M Depth New Superyacht  Submersible for sale
Superyacht  Submersible - 3 Pax - For Sale
New Superyacht  Submersible for Sale
3 Passenger Superyacht  Submersible - For Sale
10.5FT Superyacht  Submersible for Sale
---------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2678

Self Propelled Oil Barge - 600 KL - For Sale
New Build Self Propelled Oil Barge for Sale

Description :

General
Type of Vessel : SPOB (Double Bottom)
Year : New Build
Class : BKI

Particulars
Length Over All : 47.50 meters
Breadth of Moulded : 09.00 meters
Depth of Moulded : 03.60 meters
Main Engine : 2 units Yanmar Marine Engine 6HA2M-WDT 405 HP, 1.950 Rpm
Gear Box : 2 units HangZhou D300(new engine) Ratio 1 : 5
Generator : 2 units Yanmar 6TY120 40 Kva/1.500 Rpm, 50 Hz/380 Volt
Cargo Tank Capacity : ± 600 tones
Fresh Water Capacity : ± 65 tones
Fuel Oil Tank Capacity : ± 35 tones
Fuel Oil Pump : Pompa contifugal ETA N 100 x 80 - 250
Fuel Consumption : 60 liters/ hour
Speed : ± 8 knots

Navigation
Radar : 1 unit Furuno 1715
Echosounder : 1 unit Koden Echosounder CVS 216
Compass    : 1 unit Compass Daiko T- 150
Satelite : 1 unit Furuno Satelite GPS 32 VHF IC – 304and SSB IC- 710

Ship of Plate
Keel : 12 mm
Frame : 8 mm
Hull : 10 mm
Bulkhead : 8 mm
Bottom : 10 mm
Deck : 8 mm
Bris : 6 mm

Price & terms : Please enquire using the email form below

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
-----------------------------------------------------------------------------------------
Search words (for official use only) :
600 KL SPOB (Double Bottom) for Sale
BKI Classed Self Propelled Oil Barge for Sale
Self Propelled Oil Barge - 600 KL - For Sale
Self Propelled Double Bottom Oil Barge for Sale
New Build SPOB for Sale
------------------------------------------------------------------------------------------

Worldrigs ID: WR2560

2000HP Swing Up Triple Drilling Rig for sale
Used Drilling Rig for Sale

General Description
Year Built/Rebuilt : 2000
Estimated Drilling Depth : 20,000 ft
Estimated Rig Move Loads : 150
Estimated Camp Move Loads : 32
Rated HP : 2000

Mast
Height : 162.00 ft
Static Hook Load Capacity: 1,275,000 lbs
Mast Racking Capacity : 24,500 ft

Substructure
Style : Parallelogram
Height : 35.00 ft
Clear Height : 30.00 ft
Casing Capacity : 1,275,000 lbs
Maximum Setback Load (lbs.) : 750,000

Drawworks
Make : Oilwell
Model : E 2000
Power Rating : 2,000hp
Input Power : 2 ea. General Electric GE 752 DC
Brake Type - Band or Disc : Band
Drilling Line size : 1 1/2"
Auxiliary Brake : Baylor 7838 W

No Top Drive

Swivel
Make : Ideco
Model : Trueline 650 Ton
Capacity : 650 Ton

Rotary Table
Make : Lanzhou ZP-375
Table Opening : 37 1/2"
Maximum Load Rating : 650 Ton

Power Generation
SCR / VFD / DC/DC : SCR Rig

Mud System
Mud Pumps : 3 ea Oilwell A-1700 PT 1,700hp @ 150 spm
Reserve Mud Volume :2000 bbls
Pressure Rating : 5,000 psi
Active Mud Volume : 2,000 bbls
Shale Shakers : 1 ea Brandt King Cobra

Desander : Brandt 10" x 3 Cones
Desilter : Brandt 4" x 20 Cones
Mud Cleaner : N/A
Centrifuge : N/A

Price & terms : Please enquire using the email form below

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
-----------------------------------------------------------------------------------------
Search words (for official use only) :
2000HP Swing Up Triple Drilling Rig for sale
2000 Built Swing Up Triple Rig
Used Drilling Rig for Sale
Drilling Rig - 2000HP - For Sale
Swing Up - Triple - 2000 Built - Rig for Sale
162FT Land Drilling Rig for Sale
------------------------------------------------------------------------------------------

Worldrigs ID: WR1362

Propane Storage Tanks for Sale
Used McNamara LPG Storage Tanks for Sale
1948 Built - 18,000 Gallon Propane Tank for Sale

Description
Quantity : 2
Manufacturer : McNamara
Year : 1948
Pressure : U69-200psi
Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

         

--------------------------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Propane Storage Tanks for Sale
1948 Built LPG Tanks for Sale
Liquefied Petroleum Gas Storage Tank for Sale
Used McNamara Propane Tank for Sale
18,000 Gallon Capacity Propane Storage Tank for Sale
McNamara Propane Tank for Sale - 1948 Built
Used 18,000 Gallon LPG Storage Tank for Sale
---------------------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2909

Generator set - CAT3512B - For Sale
Generators for Sale

Description :

Technical Parameter
Model : 50Hz
Output Power : 1200KW
Maximum Speed : 1500 rpm
Manufacturer : CAT
Quantity : 3 sets
Manufacturing Date : 2015

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
---------------------------------------------------------------------------
Search words (for official use only) :
CAT3512B Generator set - 2015 Manufactured for Sale
1500 rpm Generators for Sale
50Hz Generators for Sale
1200KW Generators for Sale
CAT Generator set for Sale
-----------------------------------------------------------------------------

Worldrigs ID: WR1069

Mobile Solar + Wind + Diesel Generators for Sale
Hybrid Solar, Wind and Diesel Genset for Sale
Mobile Solar, Wind and Diesel Generators

Description :
This is a fully integrated sustainable hybrid electricity generator. Electricity is
generated from Solar, Wind and Diesel, making the hybrid generator a clean
& robust power source. Electricity is stored in self-maintaining deep cycle
stationary batteries.

Models vary from solar only, solar & diesel, Solar and Wind & finally Solar,Wind
and Diesel integrated. All the models are delivered fully assembled and after
rigorous testing. Ready for use on demand 24 hours a day.

The hybrid generator generator range can power a single home, factory,
hospital or an entire village. It has proven to be much more cost effective
solution to supplying power compared to diesel generators.

Model sizes vary between 3KW up to 30 KW of Power output. The hybrid
generator system architecture is designed to be plug & play and to withstand
high tolerances. An extensive warranty is provided with each system.

The hybrid generator is kind on the environment & operates silently. Integrating
a Diesel Generator is optional on all models.

The purpose of this option is for times when demand is higher than electricity
generated over long time periods. The diesel generator automatically starts,
and fills the gap between demand and generated power, and turns off
automatically when input is higher than output or equal. With all hybrid
generator models human intervention is rarely required.

Operation :
a) The system derives most of its energy through the solar Photovoltaic (PV)
array. The PV array supplies DC power to the inverter during the day and at the
same time charges a bank of batteries.

b) The inverter converts the DC power into AC at 240/400 VAC, 50/60 Hz as
required to operate appliances, tools, office equipment and more. At night
time, the batteries supply power to the inverter thereby providing reliable
power 24 hours a day.

c) There is a DC generator in the system to charge the batteries during heavy
energy usage or periods of poor sunshine. The DC generator is more efficient
and reliable than an AC generator. AC generators, however, are available. It is
possible to combine with wind turbine and AC generator.

Mobile Solar + Wind + Diesel Genset
Inverter : Surge Output
Type 1 (2) : 12 kW
Type 2 (2) : 24 kW

Inverter : Rated Output
Type 1 (2) : 6 kW
Type 2 (2) : 12 kW

Inverter : AC Voltage
Type 1 (2) and Type 2 (2)  : 230VAC/50Hz

Inverter : Phase
Type 1 (2) and Type 2 (2)  : 1-ph or 3-ph

Solar Array : kWh per day
Type 1 (2) : 22.050 kWh
Type 2 (2) : 44.100 kWh

Solar Array : Total Array Watts
Type 1 (2) : 4410 Watts
Type 2 (2) : 8820 Watts

Solar Array : Number of Panel
Type 1 (2) : 18
Type 2 (2) : 36

Solar Array : Module watts each
Type 1 (2) and Type 2 (2) : 245 watts

Battery : Size in Amp-Hours
Type 1 (2) and Type 2 (2) : 1500 AH

Battery : Bank Voltage
Type 1 (2) : 48 VDC
Type 2 (2) : 96 VDC

Battery : Bank Storage
Type 1 (2) : 72 kWh
Type 2 (2) : 144 kWh

Genset -
Type 1 (2) : 7 kW
Type 2 (2) : 14 kW

Wing Turbine -
Type 1 (2) : 1 kW
Type 2 (2) : 2 kW

Price & terms : Please enquire using the email form below

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

-------------------------------------------------------------------------------------------
Search words (for official use only) :
Mobile Solar, Wind and Diesel Genset for sale
Mobile Generators for Sale
Mobile Solar, Wind and Diesel Genset
Solar, Wind and Diesel Generators
Solar + Wind + Diesel Generators for Sale
Hybrid Solar, Wind and Diesel Generators
-------------------------------------------------------------------------------------------

Worldrigs ID: WR2537

Trailer Mounted Rack & Pinion, Super Single Rig
850HP Trailer Mounted Rack & Pinion Rig for sale
10,000ft Drilling Depth Super Single Rig for Sale

General Description
Estimated Drilling Depth : 10,000 ft
Estimated Rig Move Loads : 22
Estimated Camp Move Loads : 4
Rated HP : 850

Mast
Height : 80.00 ft
Static Hook Load Capacity: 300,000 lbs
Mast Racking Capacity : N/A

Substructure
Style : Parallelogram
Height : 15.00 ft
Clear Height : 13.00 ft
Casing Capacity : 300,000 lbs
Maximum Setback Load (lbs.) : 300,000

No Drawworks

Top Drive / Power Swivel
Make : Tesco
Model : 250 HMI 475
Capacity : 250 Ton
Torque - Continuous : 21,000 ft-lb @ 56 rpm

No Swivel
No Rotary Table

Power Generation
Engines : 2 ea. Detroit Diesel Series 6063HV35
Generators : 2 ea. Stamford Power System HCI534D
SCR / VFD / DC/DC : Rack & Pinion Rig

Enhancements
Iron Roughneck : Canrig Drilling Technology TM80-110-12-W/PCS
Power Slip Frame : TTS Sense 83415-04

Mud System
Mud Pumps : 1 ea Hong Hua HHF-1000
Power Rating : 1000 hp @ 140 spm
Reserve Mud Volume : 0 bbls
Pressure Rating : 5,000 psi
Active Mud Volume : 700 bbls
Shale Shakers : 2 ea. Derrick Corporation FLC 504

Desander : Derrick Corporation 10" x 3 cones
Desilter : American Craftman 4" x 16 cones

Mud Cleaner : N/A
Centrifuge : N/A

Well Control
Annular : 11" 5,000 psi, Townsend, Type 90
Choke Manifold : Quality Valve & Machine Works Inc, 3 1/8" 5,000 psi
BOP Closing Unit : Burnsco Bison, 6 Station 3,000 psi

Price & terms : Please enquire using the email form below

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
-----------------------------------------------------------------------------------------
Search words (for official use only) : 
Parallelogram Style Drilling Rig - For Sale
Land Drilling Rig for Sale
Used Super Single Drilling Rig for Sale
Trailer Mounted Rack & Pinion, Super Single Rig
850HP Trailer Mounted Rack & Pinion Rig for sale
10,000ft Drilling Depth Super Single Rig for Sale
Rack & Pinion, Super Single Drilling Rig for sale
Used 850HP Super Single Rig for Sale
------------------------------------------------------------------------------------------

Worldrigs ID: WR2259

32M Ocean Going Tug for sale
2007 built Ocean-Going Tug for Sale

General

Classification : Bureau Veritas
Year Built : 2007
Accomodations : 12
Working Speed : 11 Knots
Gross / Net Tonnage : 296 GT ITC / 88 NT ITC

Particulars
Length overall (LOA) : 32 Meters (104.96 Feet)
Breadth Molded : 9.114 Meters (29.89 Feet)
Depth Molded : 4.2 Meters (13.776 Feet)
Extreme Draft : 4 Meters (13.12 Feet)

Main Engines : 2-Cummins 50-M2
Generator : 2-Cummins 6 CTA 8.3-D 125 Kw
Emergency Generator : 1-Yanmar Diesel 32 Kw
Fuel Capacity : 243.6  m3 (64,352 US Gallons)
Fuel Consumption : 1300 US Gallons/Day (Estimated)
Potable Water Capacity : 54.9 m3 (14,500 US Gallons)

Horsepower (Break) : 3600
Bollard Pull (Ahead) : 35 Metric Tons (38 US Tons)

Towing Winch :
Taxing Expansion Marine Double Drum
40 Ton Hydraulic Towing Winch

Towing Wires : 2 Each,  52 mm x 700 m
Lube Oil Capacity : 3.6 m3 (951 US Gallons)

 Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

------------------------------------------------------------------------------------------------
Search words (for official use only) :
32M Ocean Going Tug for sale
2007 built Ocean-Going Tug for Sale
12 Pax Oceangoing Tug - For Sale
Used 32M Ocean Going Tug for sale
Ocean Going Tugboat - 2007 Built - For Sale
-----------------------------------------------------------------------------------------------

 

Worldrigs ID: WR598

UMD 200 Land Drilling Rig for Sale
New Semi Mobile Drilling Rig For Sale - UMD 200

Main Technical Specifications
Engine type : 2 X C 15 ACERT
Nominal engine power hp (kW) : 2 X 475 (2 X 354)
Transmission : 2 X Allison 4700 OFS
Nominal hoisting capacity metric ton (lbs) : 200 (440000)
Workover depht (m) drill pipe (2 7/8”) : 8600
Drilling depht (m) (4 1/2“) : 3700
Rope diameter (mm) : 32
Mast height (m) : 36
Drilling floor height (m) : 5-6
Travelling system : 5x4
Working pressure (mpa) : 0, 65-0, 8

Technical Specifications
Drawworks
Main Drum -
Input power (hp) : 1000
Barrel size : D24”  W42”
Brake rim size : D44” W12”
Wire line size : 1 1/4” (32 mm)
Drum speed : 7F/1R
Lubrication : Automatic or manual
Drum clutch : Air flex type
Brake cooling : Water circulation
Brake system : Band / disc / auxiliary (Parmac SSR-28 hydro-brake)
Chain drives : All chains are fully encloded for oil bath lubrication ensuring
longer life and cleaner operation

Sand Line Drum -
Barrel size : D13”  W37“
Brake rim size : D44” W9½”
Spooling capacity : 16114’
Sand line wire size : 9/16” (14 mm) - 5/8” (16 mm)

Rig Power & Transmission
Diesel engine(s) : 2 x Caterpillar C-15 ACERT, 540Hp, 2.100rpm
Transmission(s) : 2 x Allison OFS 4700 series with torque converter
Right angle gear box : Min 1000 hp gear box in oil bath gear case
Compound box : Twin engine drive through transmission includes disconnect clutches
at compound shaft for engines

Mast  & Crown Block
Mast -
Mast complete set : Design and conform to APÄ° 4F specification
Mast height : 36m  ( 118ft  )
Max. static hook load capacity : 1.960kN  ( 440.000lbs )
Racking capacity : 3.000m ( 4 ½’’ DP，19.2m double )
Mast type : Hydraulic telescopic
Height of the monkey board : 17.2m ( from floor )
Accessories : Two (2) X hydraulic catheads , Two (2) X tong weight boxes ,
standpipe , exproof  lightning....etc

Crown Block -
Crown block complete set - Design and conform to APÄ° 4F  specification
Max. hook load - 1.960kN (440.000lbs )
Number of sheaves - (3)  Main + (1) fast line  +  (1) deadline +  (1) sandline  +
(2) sheaves for service winch

Sheaves OD :
Fast Lines Ø36" ( Ø915mm )
Dead Line Ø32" ( Ø813mm )
Sand Line Ø32" ( Ø813mm )

Dia. of sheave’s grove :
Fast & Dead Lines Ø1 1/4 " ( Ø32mm )
Sand & Winch Lines  Ø 5/8" ( Ø16mm )

Substructure
Substructure complete set : Design and conform to APÄ° 4F specification
Height of substructure substructure : 5.5m
Area of substructure : 40m2
Max. static rotary load : 2.000kN
Set back capacity : 1.000kN
BOP lifting tools : 3tons capacity electric or mechanic winches
Accessories : Mouse, rat hole, dog house

Rotary Table
Diameter of Opening : 27½"
Center of Table to Centerline of Sprocket Teeth : 53¼"
Maximum Static Load, ton : 500
Max Speed, rpm : 300
Gear Ratio : 3.67
Dimensions (LxWxH), in : 94×66×27
Approximate Weight, lbs : 13,500

Traveling Block  & Hook
Traveling block : 2.000kN max. statik load, 4 sheaves, Ø36’’ sheaves
dia. Ø1 1/4’’  (Ø32mm ) groove dia..
Hook : 2.000kN max. statik load, 5tons spring stroke.
Elevator link(s) : 2.000kN rated load capacity.

Swivel
Static hook load, ton : 200
Working pressure, psi : 5,000
Maximum speed, rpm : 300
Coupling thread to stem : 7-5/8" Reg LH
Coupling thread to kelly : 6-5/8" Reg LH
Stem Ä°.D. : 3"

Trailer  & Other Systems
Trailer :
Three axles semi mobile trailer, 16 wheels, fabricated high tensile steel vehicle
frame reinforced at points of greatest stress. Highway equipment and cab
included. Installed fuel tank. Tool box. Auxilary drill line drum, all axles dressed
brake, folding walkways on both sides of trailer.

Hydraulic jacks : Six hydraulic operated leveling jacks
Hydraulic service winch : 5 metric tons drum pull capacity
Deadline anchor : Deadline anchor attached directly to trailer frame
Air system : Compressor (engine drive), air tank, relief valves, air dryer, gauges, all clutches

Hydraulic system :
Hydraulic pump, system operate hydraulic cylinders on mast, hydraulic jacks,
hydraulic pipe tong, and hyraulic winch. Control valves, hydraulic oil tank, filters,
pipes, hydraulic and air valve connections, fittings.

Electrical lighting system : All the electrical equipments on the mast, and substructure
are ex-proof type

Instrumentation : Driller control panel, weight indicator, gauges, air valves, cables, hoses,
fittings, transducers, paint

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------
Search words(for official use only) :
UMD 125 Drilling Rig For Sale in Europe
New UMD 125 Semi Mobile Drilling Rig For Sale
New Semi Mobile Drilling Rigs
Land Drilling Rigs For Sale
New Land Drilling Rig
------------------------------------------------------------------------------------------

Worldrigs ID: WR655

Jackup Drilling Package For Sale
Rig Drilling Package
Used Drilling Package from a Rig For Sale
Offshore Drilling Package

This is a offshore driling package.

Offshore Drilling Package
Used Drilling Package from a Rig For Sale
Used Drilling Package for Sale
Rig Drilling Package

This is a drilling package including derrick, cantilever, texas deck etc,
which is coming available to the market because the drilling rig is
going to be converted into an accommodation rig.
 
Used Rig Drilling Package for Sale

A.1.1.1 Rig Floor Winches (Non Man-riding)
Quantity no. : 2
Make : Ingersol Rand
Type : K5UL
Rated capacity lbs : 5,000
Wire diameter inch : 1/2

A.1.1.2 Monkey Board Work Winch
Quantity no. : 1
Make : Ingersol Rand
Type : Airdyne
Rated capacity lbs : 1 ton
Wire diameter inch : 3/8
Automatic brakes yes/no : Yes
Overload protection yes/no : No
Quantity no. : 1
Make : Ingersol Rand
Type : Pullstar PS 1000R
Rated capacity lbs : 1 ton
Wire diameter inch : 3/8
Automatic brakes yes/no : Yes
Overload protection yes/no : No

A.1.1.3 Rig Floor "Man-Riding" Winch (Utility)
Quantity no. : 2
Make : RAM
Type : ML336 Catalina
Rated capacity lbs : 330
Wire diameter inch : 3/8”
Non-twisted wire yes/no : Yes
Automatic brakes yes/no : Yes
Overload protection yes/no : Yes
Automatic spooling yes/no : Yes
Certified for man-riding yes/no : Yes

A.1.1.3.1 BOP Service Area “Man-Riding” Winch(Utility)
Quantity no. : 2
Make : Ingersol Rand
Type : FA 150K Gi
Rated capacity lbs : 330
Wire diameter inch : 3/8”
Non-twisted wire yes/no : Yes
Automatic brakes yes/no : Yes
Overload protection yes/no : Yes
Automatic spooling yes/no : Yes
Certified for man-riding yes/no : Yes

A.1.1.4 Utility Winch (ie Deck Winch)
Quantity no. : 6
Make : Ingersol Rand
Type : K5UL
Rated capacity lbs : 10,000
Wire diameter inch : 3/4
Automatic brakes yes/no : No
Overload protection yes/no : No
Automatic spooling yes/no : No
Certified for man-riding yes/no : No Locations                                                           :

A.1.1.5 BOP Hoists (see E.10.1)
Quantity no. : 2
Make : BEEBE
Type : Overhead Bridge Crane
Rated capacity st : 37.5 tons / Crane
Location : Underside of drill package

B General Rig Specifications

B.1 Derrick and Substructure

B.1.1   Derrick/Mast
Make/type : Joseph Paris
Rated for windspeed
- With full set back knots : 100
- With no set back knots : 100
Height ft : 162
Dimensions of base ft x ft : 36 x 36
Dimension of crown ft x ft : 18 x 18
Gross nominal capacity lbs : 1,485,714
Static hook load lbs : 1,300,000
Maximum number of lines no. : 14 (12 in use)
Ladders with safety cages and rests yes/no : Yes
Platform for crown sheaves access yes/no : Yes
Counter balance, system for rig tongs
pipe spinning tong yes/no : Yes
Lighting system explosion proof yes/no : Yes

B.1.2   Racking Platform
Make/type : Total capacity-drill pipe :
- 5" DP ft : 20,000
- 6-5/8" DP ft : 9,000
- 3-1/2" DP ft : 20,000

Total capacity-drill collars :
 
- 8" DC ft : 7 stands
- 9" DC ft : 3 stands

Tubing Bellyboard yes/no : No

B.1.3   Substructure
Make/type : CFEM
Drill floor height (above main deck) ft : 37.35
Width ft : 77.34
Length ft : 44.57
Setback capacity kips : 606
Simultaneous setback-hookload capacitykips : 1,200
Rotary beam capacity (total) kips : 903
Clear height below R/table beams (to main deck) ft :

B.1.4   Weather Proofing
Rig floor windbreaks yes/no : Yes
- Height ft  : 
Derrickman windbreaks yes/no : Yes
- Height ft :
Around process pits yes/no : Yes
- Height ft :

B.1.5   Derrick TV Camera System
Camera located at : Monkey board level in derrick
Make/type : Ocular 12EX PTZ EExd Camera
Zoom/pan/tilt-function yes/no : Yes
Monitor located at : Drillers house (Ocular 4M EEx de 11G T6 Monitor)
Camera located at : Stabbing board level
Make/type : Ocular 12EX PTZ EExd Camera
Zoom/pan/tilt-function yes/no : Yes
Monitor located at : Drillers house (Ocular 4M EEx de 11G T6 Monitor)

B.2 Drawworks and Associated Equipment

B.2.1   Drawworks
Make/type : National 1625 DE
Motors make/type : Jeumont Schneider DC 752
- Quantity no. : 2
- Rated input power hp : 1,000
Motors make/type : GE DC 752
- Quantity no. : 1
- Rated input power hp : 1,000
Drum size (dia & length) in x in : 36 x 61-1/2
Drum type (grooved/smooth) : Grooved
- For drill line size in : 1-1/2
Brake type (disc/drum) : Drum
Max line pull (12 lines) lbs : 1,250
Max line pull (10 lines) lbs : 1,075
Max line pull (8 lines) lbs : 880
Makeup cathead type : Foster
Breakout cathead type : Foster
 
Crown block safety device :
- Make/type : National Crown-o-Matic
Independent fresh water cooling system
for drawworks and electric brake yes/no : Yes
Automatic driller yes/no : No :
 
B.2.2   Auxiliary Brake
Make : Elmagco
Model : 7838
Independent back-up system type : KEMS
 
B.3 Derrick Hoisting Equipment

B.3.1   Crown Block
Make/type : Joseph Paris (overhauled)
Rated capacity st : 715
No. of sheaves no. : 8
Sheave diameter inch : 60
Sheave grooved for line size inch : 1.5
 
B.3.2   Travelling Block
Make/type : National / Type H, 760H650
Rated capacity st : 650
No. of sheaves no. : 7
Sheave diameter inch : 60
Sheave grooved for line size inch : 1.5

B.3.3   Hook
Make/type : National / Type H-650
Rated capacity st : 650
Complete with spring assbly/hook yes/no : Yes
locking device

B.3.4   Swivel
Make/type : National / P-650 (Integrated with TDS-4S)
Rated capacity st : 650
Test/working pressure psi : 5,000
Gooseneck and washpipe min id in : 3
Left hand pin connection type : 7-5/8 Reg
Access fitting for wireline entry yes/no : Yes on top of gooseneck

B.3.5   Drilling Line
Diameter inch : 1-1/2
Construction : 6 x 19 IPS IWRC
Length (original) ft : 7,500
Drilling line reel :
- Drum cover yes/no : Yes
- Drilling line drum power drive yes/no : No
Spare drilling line yes/no : No
Location (rig, shore, etc) : Rig
Roller guides yes/no : Yes

B.3.6   Dead Line Anchor
Make/type : National / Type EB
Weight sensor yes/no : Yes
Dead line dampener yes/no : Yes

B.3.7   Block Guidance System
Make/type : BSI Track & Dolly/ non-retractable

B.4 Rotating System

B.4.1   Rotating Table
Make / type : National C-495
Maximum opening inch : 49-1/2
Rated capacity st : 800
Two speed gearbox yes/no : Yes
Emergency chain drive yes/no : No
Driven by an independent electric motor   yes/no : Yes
- Electric motor type/make : Jeumont Schneider
- Maximum continuous torque ft/lbs : 
- Output power hp : 1,000
 
Drip pan/mud collection system yes/no : Yes

B.4.2   Master Bushings
Make/type : Varco
Inserts bowls (see G.1.8) : No. 1, 2, 3, DP/DC

B.4.3   Top Drive
Make : Varco TDS-4S
Type (electric/hydraulic) : Electric
Rated capacity st : 650
Test/working pressure psi : 5,000
Output power hp : 1,100
Maximum continuous torque ft/lbs : 45,500 Low Gear / 29,500 High Gear
Two speed gear box yes/no : Yes
Maximum rotary speed rpm : 125 Low Gear / 205 High Gear
Remote operated kelly cock yes/no : Yes
Cooling system type : Close Loop System (remote blower)

B.4.3.1 Top Drive Makeup/Breakout System
Make/Type : Varco/Torque Wrench/Pipe Handler
Model : PH-85
Max makeup torque ft/lbs : 85,000
Max. breakup torque : ft/lbs : ,000
Raised backup system : yes/no : No
- Make/type :

C Power Supply Systems

C.1.1   Compressed Air Systems
Air compressors - low pressure (bulk air) :
- Quantity no. : 1
- Make : Ingersol-Rand
- Model : 650L
- Rated capacity ft3/min : 750 cfm
- Working pressure psi : 40
- Prime mover (electric/diesel) : Electric
- Continuous power hp : 154.5 

Air dryers:
- Quantity no. : 1
- Make/type : R800A Pioneer Refrigerated Air Dryer
- Rated capacity ft3/min : 100 btu/min 100 SCFM to ambient

C.1.2   Air Receivers
Quantity no. : 1
Volume (total) ft3 : 2.25 m3
Pressure psi : 125
Location : Drill Floor

D Drillstring Equipment

D.1.1   Drill Pipe
Drill pipe OD inch : 5
Grade : S-135
Total jnts : 137
Range : Weight lbs/ft : 19.5
Internally plastic coated yes/no :
Tool joint OD/ID in/in : 6-5/8 - 3-1/4
Tool joint pin length (original) inch : 6-3/4
Tapered shoulder tool joints (box/pins)degree : 18
Connection type : 4-1/2 IF Bevel : 5-59/64 in
Type of hardfacing : Arnco 200XT (6000 ft)
API classification : Premium
Thread protectors yes/no : Yes
Installation tools (manual, hydraulic, none) :

Drill pipe OD inch : 5-1/2”
Grade : EU-S
Total jnts : 310
Range : 
Weight lbs/ft : 
Internally plastic coated yes/no : 
Tool joint OD/ID in/in : 
Tool joint pin length (original) nch : 
Tapered shoulder tool joints (box/pins)degree :
Connection type : 
Bevel :
Type of hardfacing : 
API classification : 
Thread protectors yes/no : Yes
Installation tools (manual, hydraulic, none) : 

D.1.2   Hevi-Weight Drill Pipe
Quantity no. : 1
Nominal size OD inch : 5
Weight lbs/ft : 49.5
Range : 2
Tool joint OD / ID inch : 6-1/2 / 3
Type of hardfacing : Hughes Smooth AX@
Internally plastic coated yes/no : Yes
Connection type : 4-1/2 IF
Thread protectors yes/no : Yes
Quantity no. : 45
Nominal size OD inch : 5-1/2” Spiral
Weight lbs/ft : 
Range : 
Tool joint OD / ID inch : 
Type of hardfacing : Hughes Smooth AX@
Internally plastic coated yes/no : Yes
Connection type : 
Thread protectors yes/no : Yes

D.1.3   Drill Collars
Quantity no. : 6
OD body inch : 8-1/4
ID body inch : 
Nominal length of each joint ft : 31
Drill collar body (slick/spiral) : 
Spiral Recess for "zip" elevator yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no : 
 
Boreback on box yes/no : 
Connection type : 6-5/8
REG Quantity no. : 8
OD body inch : 8
ID body inch : 2.813
Nominal length of each joint ft : 31
Drill collar body (slick/spiral) : 
Spiral Recess for "zip" elevator yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no : Yes
Boreback on box yes/no : Yes
Connection type : 6-5/8
REG Quantity no. : 8
OD body inch : 6.5
ID body inch : 2.813
Nominal length of each joint ft : 30
Drill collar body (slick/spiral) :  
Spiral Recess for "zip" elevator yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no : Yes
Boreback on box yes/no : Yes
Connection type : 4 IF

Quantity no. : 12
OD body  inch : 6-1/2”
ID body inch : 
Nominal length of each joint ft : 31
Drill collar body (slick/spiral) :  
Spiral Recess for "zip" elevator   yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no : 
Boreback on box yes/no :
Connection type : 
Quantity  no. : 
OD body inch : 
ID body inch : 
Nominal length of each joint ft : 
Drill collar body (slick/spiral) : 
Recess for "zip" elevator yes/no : 
Recess for slips yes/no : 
Stress relief pin groove yes/no : 
Boreback on box yes/no : 
Connection type :  6-5/8
REG Quantity no. : 8
OD body inch : 
ID body inch : 
Nominal length of each joint ft :
Drill collar body (slick/spiral) : Spiral
Recess for "zip" elevator yes/no : 
Stress relief pin groove yes/no :
Boreback on box yes/no : 
Connection type : 
 
D.1.4   Inside BOP Valve
Quantity no. : 1
Make : TIW
OD inch :  5
Min. drill pipe ID required inch : 3-1/4
Connection type : 4-1/2 IF
Working pressure rating psi : 10,000

D.1.5   Kelly Cocks
Upper inside BOP (see also D.1.15)
- Quantity no. : 1 upper
- Make/type : Varco
Working pressure psi : 15,000
Max OD body in : 7-3/4
Max ID body in : 3
Connection type (box) : 7-5/8 Reg
Connection type (box) :  7-5/8 Reg
Lower inside BOP Manual
- Quantity no. : 1 lower
- Make/type :
Working pressure psi : 15,000
Max OD body in : 7-3/8
Max ID body in : 3
Connection type (box) : 7-5/8
Connection type (pin) : 7-5/8

D.2 Handling Tools

D.2.1   Hydraulic Makeup/Breakout Machine (e.g. EZ Torque)
Make/Type : Ezy Torque
Maximum linepull : 35,000 lb

D.2.2   Iron Roughneck
Make/type : Varco AR 3200
Size range (max OD/min OD) in/in : 3-1/2 / 9-1/2
Max makeup torque ft/lbs : 90,000
Max breakout torque ft/lbs : 100,000

E  Well Control

E.1 Diverter
Fixed yes/no : No
- Make/type : 
- Maximum bore in : 
- ID of insert packer in : 
- Working pressure psi : Annular yes/no : Yes
- Make/type : Hydril MSP
- Maximum bore in : 29-1/2
- Working pressure psi : 500
Bottom connection : Flanged
- Size in : 30
- System pressure psi : 1,500 working
- Gasket type : R-95
Number of diverter outlets no. : 2
Outlet OD (nominal) in : 12

E.1.1 Diverter Flowlines 
Quantity no. : 1
Nominal size of flowlines
Running from diverter to : Overboard (aft)
Valve make/type : Ball
- Quantity no : 2
- Size in : 12
- Working pressure : 500
- Valve operator (air/hydraulic) : Hydraulic
System pressure rating  psi : 500
Flex hose in flowline Yes/no : No

E.1.2 Diverter Control Panel  
Primary make/type : Koomey
- Location : Under Cantilever
Remote make/type : Koomey / Type 80
- Location : Driller’s house and Toolpusher office

E.2 High Pressure Blowout Preventers
All appropriate components H2S rated yes/no : Yes

E.2.1 Kill Line Valves
Quantity no. : 2
Make/type : Cameron
Size : 3-1/16
Working pressure  psi : 15,000
Gasket type : BX-154
Hydraulic/manual/non-return : 1manual & 1 hydraulic

E.2.2  Choke Line Valves 
Quantity no. : 2
Make/type : Cameron
Size in : 3-1/16
Working pressure psi : 15,000
Gasket type : BX-154
Hydraulic/manual no. : 1 manual & 1 hydraulic

E.3   BOP Control System

E.3.1 Accumulator Unit
Make/model : Koomey Type 80
Location Inside hull
Fluid reservoir capacity  US gal : 502
Oil/water mix rate US gpm : Hydraulic oil (Oceanic HW-540)
Glycol reservoir capacity US gal : None
Total accumulator capacity (w/o precharge)  USGal : 210
System working pressure psi : 3,000
Control manifold model : Koomey
Regulator type : KR
Total useful accumulator volume equals all
preventer opening and closing volumes  yes/no : Yes
- Plus percent additional volume % : 50%

E.3.2 Accumulator Hydraulic Pumps
Electric driven :
- Quantity no. : 2
- Make/model : Koomey
- Each driven by motor of power hp : 30
- Flow rate of each pump US gpm : 142
- At operating pressure psi : 3,000
- Operable off emergency generator yes/no : 1 - normal power, 1 - emergency generator
Air driven yes/no : Yes
- Quantity no. : 2
- Make/model : Koomey / U9A26
- Flow rate of each pump US gpm : 6.4
- AT operating pressure psi : 3,000

E.3.3 Primary Control Panel
Control panel make/model : Koomey
Location : Under cantilever
Panel controls for the following functions :
- All annular BOPs yes/no : Yes
- All ram BOPs yes/no :  Yes
- Lock for ram BOPs yes/no : No
- Diverter System yes/no : Yes
- Kill and choke line valves yes/no : Yes
- Low accumulator pressure warning  yes/no : Yes
- Low reservoir level warning yes/no : Yes
- Low rig air pressure warning yes/no : Yes
- System pressure regulator yes/no : Yes
- Pressure regulator for annular yes/no : Yes
- Flowmeter yes/no :  Yes
- Quantity of pressure gauges no. : 5
- Other control functions yes/no : No

E.3.4 Remote Control Panels
Make/model : Koomey Zone I
Location : Rig floor
Location : TP office
Ability to operate main closing unit valves
directly yes/no : Yes
System routing (direct/thru panel) : Direct
Remote control of system pressure
regulator yes/no : Yes (from the Drill Floor)
Remote control of annular pressure
Regulator yes/no : Yes (from the Drill Floor)

E.4 Choke Manifold

All appropriate components H2S rated yes/no : Yes
 
E.4.1 Choke Manifold (For instrumentation, see H.3)
Nominal size in : 3-1/16
Minimum ID in : 3.063
Maximum working pressure psi : 15,000
Quantity of fixed chokes no. : 1
- Make/model : Demco
- Size (ID) in : 3
Quantity of adjustable chokes  no. : None
- Make/model :
- Size (ID) in : 
Quantity of power chokes no. : 2
- Make/model : Demco
- Size (ID) in : 2 in max
Power choke remote control panel yes/no : Yes
- Make/model : Demco
- Location : Driller’s house
- Glycol injection yes/no : No

E.5 Flexible Choke &Kill Lines (BOP to Manifold)
Quantity no. : 2
Make/type : Hose
ID in : 3
Working pressure psi : 15,000
H2S service yes/no : Yes

E.6 Flexible BOP Control Hoses
Quantity no. : 16
Make/model : Hydrasun
Size (ID) in : 1
Working pressure psi : 3,000
Fire resistant yes/no : Yes

E.7 BOP Testing Equipment

E.7.1 Hydraulic BOP Test Pump
Make/model : Koomey
 Type : Air
Pressure rating psi : 30,000
Chart recorder yes/no : Yes

E.7.2 BOP Test Stump
Size in : 13-5/8, 15,000psi

E.8 BOP Handling

E.8.1 BOP Hoist System
Make/type : BEEBE Quantity of hoists no. : 2
Number of lift points on BOP no. : 2
System safe working load (max BOP wt) st :  2 x 37.5 tonnes 

E.8.2 Work Platforms
BOP work platform (adjustable/fixed/none) : Fixed
Conductor pipe platform yes/no : Yes

E.8.3 Conductor Pipe Tensioning System
Make/type : Hydril
Tension capacity st : 300 kips
Number of lift points no : 4
Stroke in : 16

F  Mud System / Bulk System

F.1  High Pressure Mud System
System working pressure psi : 5,000
System test pressure psi : 5,000

F.2 Mud Pumps
Quantity  no. : 3
Make : National-Oilwell
Model : 12-P-160
Type (triplex/duplex) : triplex
Mud pump drive motors no. : 2
- Motor type : Jeumont Schneider DC 752
- Continuous power rating per motor : 1,600 hp
Mud pump drive motors no. : 1
- Motor type : GE DC 752
- Continuous power rating per motor : 1,600 hp
Fluid end type : Southwest
- Maximum working pressure psi :  5,000
- Test pressure psi : 5,000
Pump stroke counter type : Martin Decker
Supercharging pump type : Mission
- Driven by motor of power hp : 75
Discharge suction line ID inch : 12
M.P Pulsation dampener type : Hydril
Reset relief valve : Retsco Type B Working flowrate per pump at
90% of max gpm : 600 gpm
- Liner size inch : 6-1/2
- Pump speed (90% of max) spm : 120
- Pump pressure psi : 3,900
- Working flowrate US gpm : 514

F.2.1 Transfer Pumps / Mixing Pumps
Mixing Pumps :
- Quantity no. : 2
- Make/model : Mission Magnum 1
- Type/size : Centrifugal / 8x6R
- Output capacity US gpm : 1,200
- Drive motor type : Electric
- Power output hp : 75
Transfer Pumps :
- Quantity no. : 2
- Make/model : Mission Magnum 1
- Type/Size : Centrifugal/8 x 6R
- Output capacity US gpm : 1,200
- Drive motor type : Electric
- Power output hp : 75

F.2.2 Standpipe Manifold
Quantity of standpipes no. : 2
Standpipes ID inch : 4 (5-9/16” OD)
H-Type standpipe manifold yes/no : Yes
Kill line outlet yes/no : Yes
Fill-up line outlet yes/no : Yes
 Bleed-off line outlet yes/no : Yes

F.2.3 Rotary Hoses
Quantity no. : 1
Make/type :
ID x Length inch x ft : 3-1/2 x 80
Working pressure psi : 5,000
Snubbing lines yes/no : Yes

F.2.4 Cementing Hoses
Quantity no. : 1
Type (armor sheath/flexible steel pipe) : Steel internal wound Rubber
Length ft : 80
ID Inch : 2
Working pressure psi : 10,000

F.3 Low Pressure Mud System

F.3.1 Shale Shakers
Primary :
- Quantity no. : 3 (brand NEW not commissioned even)
- Make/model : Axiom AX1
- Type :
- Nominal flow rate (total) bbl/min : Variable up to 1000gpm per shaker
dependent on screen size and fluid properties 

F.3.2 Mud/Gas Separator (Poor Boy)
Make/type : Swaco
Dimensions (height x OD) ft x in : 10 ft x 4 ft
Gas discharge line ID in : 8 in
Gas discharge location, primary : Crown A-frame
Can discharge be tied into burner system : No
Vacuum break yes/no : Yes
Mud seal height  ft : 24
Pressure gauge yes/no : Yes
Calculated gas throughput mmscf : 17.83 

F.3.3 Degasser
Make/type : Wellco 5200
Nominal flow rate bbl/min : 600
Feed pump make/model : Mission 6 x 8
- Type/size :
- Capacity gpm : 1,200
- Drive motor hp hp : 75
Is pump dedicated to degasser yes/no : Yes
Vacuum pump make type : Wellco

F.3.4 Mud Agitators
Quantity no. : 1
Make/model : Swaco SWM-5
Driven by motor of power hp : 5
Located in tanks : Slug pit
(see F.2.1 & F.2.2 for tank designations)
Quantity no. : 4
Make/model : Swaco SWM-25
Driven by motor of power hp : 25
Located in tanks : Tanks 1, 2, 3, 4
(see F.2.1 & F.2.2 for tank designations)

F.4 Bulk System

F.5 Barite/Bentonite Silos
Quantity no. : 4
Capacity of each silo ft3 : 1307
Locations : P/tank room
Type weight loadcell : Martin Decker
Manufacturer : Totco
Pressure rating psi : 40
Relief valve(s) installed yes/no : Yes

F.5.1 Cement Silos
Quantity no. : 4
Capacity of each silo  ft3 : 1307
Locations : P/tank room
Type weight loadcell : Martin Decker
Manufacturer : Totco
Pressure rating psi : 40
Relief valve(s) installed yes/no : Yes
Separate mud/cmt loading facilities yes/no : Yes
Cement discharge independent from
barite/bentonite yes/no : Yes

F.5.2 Surge Tank for Barite/Bentonite
Quantity no. : 2
Capacity of each tank ft3 : 70 ft3
Type weight loadcell : Totco
- Manufacturer : Totco
Pressure rating psi : 20
Relief valve(s) installed  yes/no : Yes

F.5.3 Mud Hopper
Quantity no. : 2
Make/model : Double Life Jetting
Feed pump make/model : ASF.12
Type/size : Capacity bbl/min : 1,200
Drive motor hp hp : 
Is feed pump dedicated to mud hopper(s) yes/no : No

G Casing / Cement Equipment

G.1 Cementing Equipment

G.1.1  Cementing Manifold
Discharge manifold working pressure : 15,000 psi
Cement pump discharge lines min ID : 2 in
Cement pump discharge lines
working pressure psi : 15,000
Manifold safety pressure relief valve yes/no : Yes 

G.1.2  Cementing Standpipe
Quantity no. : 1
Working Pressure psi : 15,000
ID inch : 3
Connection to choke manifold yes/no : Yes
Connection to standpipe manifold yes/no :  Yes

H Instrumentation/Communication

H.1 Drilling Instrumentation at Driller's Position

H.1.1   Weight Indicator
Make/type : Martin Decker / Type E-80
Sensor type : AWE 9-1

H.1.2   Standpipe Pressure Gauges
Quantity no. : 1
Make/type : Martin Decker
Max. pressure reading psi : 5,000
Quantity no. : 1
Make/type : Martin Decker
Max. pressure reading psi : 5,000

H.1.3   Choke Manifold Pressure Gauge
Quantity no. : 1
Make/type : Stewart & Stevenson
Max. pressure reading psi : 15,000
Quantity no. : 1
Make/type : Martin Decker
Max. pressure reading psi : 15,000
 
H.1.4   Rotary Instrumentation

H.1.4.1 Tachometer
Make/type : Martin Decker
Maximum RPM rpm : 250

H.1.4.2 Torque Indicator
Make/type : Martin Decker
Maximum torque ft/lbs : 50,000

H.1.5   Top Drive Instrumentation

H.1.5.1 Tachometer
Make/type : Martin Decker
Maximum RPM rpm : 250

H.1.5.2 Torque Indicator
Make/type : Martin Decker
Maximum torque ft/lbs : 50,000

H.1.6   Pump Stoke Counters
Quantity no. : 2
Make/type : Totco
Stoke indicator and cumulative
Stroke counter for each pump : Yes

H.1.7   Tong Torque Indicator
Make/type : Martin Decker
Maximum torque ft/lbs : 25K x tong length

H.1.8   Pit Volume Totalizer
Make/model: Electro Flow
Floats in active mud tanks : Yes
- Quantity per tank : no. : 1
Floats in reserve mud tanks : Yes
- Quantity per tank  no. : 1
Floats in mud processing tank : Yes
- Quantity per tank : no. : 1
Loss/gain indicator  yes/no : Yes
Audio Alarm yes/no : Yes
Visual Alarm yes/no : Yes

H.1.9   Mud Flow Indicator
Make/model : Electro Flow
High/low Alarm : Yes
- Audio Alarm yes/no : Yes
- Visual Alarm yes/no : Yes
Sensor location : Flow line

H.1.10 Trip Tank Indicator
Make/model : Electro Flow
Chart recorder yes/no : Yes
 
Alarm yes/no : Yes

H.2 Drilling Parameter Recorder
Quantity no. : 1
Make/type : Petron Drill Graf
Location - 1 : Driller’s house
- Type (display/recorder/both) : Display
Number of parameters recorded no. : 6
Parameter recorded : Weight
Parameter recorded : Pump pressure
Parameter recorded : Rotary torque
Parameter recorded : Rotary RPM
Parameter recorded : Pump SPM
Parameter recorded : Penetration rate

Brand new Electro wave Transocean Driller’s display system,
not commissioned yet.

H.3 Instrumentation at Choke Manifold

H.3.1   Standpipe Pressure Gauge (Drillpipe Pressure Gauge)
Quantity no. : 1
Make/type : Houston Digital Display
Pressure range (max.) psi : 6000
Visible from choke operation position : Yes

H.3.2   Choke Manifold Pressure Gauge (Casing Pressure Gauge)
Quantity no. : 1
Make/type : Houston Digital Display
Pressure range psi : 6000
Visible from choke operating position : Yes

H.4 Instrumentation at Standpipe

H.4.1   Standpipe Pressure Gauge
Quantity no. : 2
Make/type : MD Totco
Pressure range psi : 8000
 
Visible from drillers position : Yes
Visible from choke operation position : Yes

H.5 Rig Communication Systems

H.5.1   Rig Telephone System
No. of stations no. : 67 extensions
Make/type : Panasonic KXDT 1232
Explosion proof yes/no : Yes

H.5.2   Public Address System
Can be combined with H.6.1 above: yes/no : Yes
No. of stations no. : 67 (access from all telephones)
Make/type  :  Federal Signal Dual Redundant
Explosion proof  yes/no : Yes - where applicable

H.5.3   Drill Floor Talkback System
No. of stations no. : 2
Location : Drill floor
Location : Monkey board
Make/type : Gaitronics
Explosion proof yes/no : Yes

H.6 External Communications Equipment

I Workover Tools

J Accommodation

J.1 Living Quarters

J.1.1 Accommodation Block
Total beds: no. : 43
- No. of beds per room type (1, 2, 3, etc.) no. :  2 (1 ea. 1 man)
- Number of rooms no. :  22
- Toilets (shared) no. : 0
- Showers (shared) no. : 0
Total beds: no. : 43 

K Safety Equipment

K.1 General Safety Equipment

K.2 Rvival Equipment

K.2.1   Lifeboats
Make/type : Survival craft 75 C
Quantity no.  : 4
Capacity (person/craft) :  60
Locations (port, stbd) :  Port and stbd
Fire protection yes/no : Yes
Radio/EPIRB (see Section H.9) :  NO

K.2.2   Davits
Davits :  4 ea.
Make : Survival craft inspectorate
Type : Rig Master SWL : 8.5 T
Class : DNV
Year : 2008

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------------------
Search words (for official use only) - 
Jackup Drilling Package For Sale
Offshore Drilling Package
Drilling Package For Offshore for sale
Complete Drilling Package For Sale
Complete Jackup Drilling Package For Sale
Jackup Used Drilling Units for Sale
Rig Drilling Package
Used Drilling Unit Form a Jackup Rig
-------------------------------------------------------------------------------------------------------

Worldrigs ID: WR665

Floating Crane for Sale
600 ton floating crane
600 Ton Afloat Crane For sale

Specifications
Type : All Revolving self-propelled
Type of vessel : Floating Crane
Classification : China ZC
Lifting Capacity : 600ton Max Lifting Capacity by test : 650ton
Date of construction : in Sep. 2005

LOA : 70.60m
Length : 67.1.
Breadth : 30.00m
Depth : 5.20 m
Light draught : 2.200 m
Full-load draught : 2.400 m
Full-load displacement : 4022.00 t
Light displacement : 3650.00 t

Navigation area : coastal/offshore area
Business area : A1+A2
Hull material : steel
Deck material : steel
Number of deck layers : 1
Special loading equipment on deck : floating equipment on deck
Gross tonnage : 3311
Net tonnage : 993

Part of Equipment
Anchor
Quantity of ship equipment 543 Quantity of anchor 4 Quantity of anchor windlass 4

Anchor -
Name : Right bow anchor
Type : Navy anchor/high holding power anchor
Weight : 4000.00

Name : Right bow anchor
Type : Navy anchor/high holding power anchor
Weight : 4000.00

Name : Left bow anchor
Type : Navy anchor/high holding power anchor
Weight : 4000.00

Name : Left bow anchor
Type : Navy anchor/high holding power anchor
Weight : 4000.00

Anchor Windlass -
Name : Right bow anchor  windlass
Type : IZQ850
Power (kw) : 30.00
Builder : Shanghai Fishery machinery factory

Name : Right bow anchor  windlass
Type : IZQ850
Power (kw) : 30.00
Builder : Shanghai Fishery machinery factory

Name : Right bow anchor  windlass
Type : IZQ850
Power (kw) : 30.00
Builder : Shanghai Fishery machinery factory

Name : Right bow anchor  windlass
Type : IZQ850
Power (kw) : 30.00
Builder : Shanghai Fishery machinery factory

Anchor Chain -
Name : Right bow
Diameter (mm) : 42.00
Length (m) : 500.00
Material : Steel wire rope

Name : Right bow
Diameter (mm) : 42.00
Length (m) : 500.00
Material : Steel wire rope

Name : Left bow
Diameter (mm) : 42.00
Length (m) : 500.00
Material : Steel wire rope

Name : Left bow
Diameter (mm) : 42.00
Length (m) : 500.00
Material : Steel wire rope

Water fire-extinguisher system -
Fire pump type : Main fire pump
Model : 100CWZ-14
Displacement (m3/h) : 100
Pressure head (Mpa) : 0.30
Quantity : 1

Fire pump type : Emergency fire pump
Model : 100CWZ-14
Displacement (m3/h) : 100
Pressure head (Mpa) : 0.30
Quantity : 1

Fire Extinguisher -
Type : Various
Quantity : 22

Fire detection and fire alarm system : quantity * 12
Life-saving facilities : meet 12 people
Life Vest : 14pcs
Navigation equipment : equipped
Signal equipment : equipped

Radio equipment/wireless apparatus/ wireless
telephone/ radio telephone : Equipped

Main engine : 4 units
Rated Power : 220KW
Rotating speed :1000r/min
Power generating equipment

Type -
No.1 power generating set : 388GFC1
No.2 power generating set : 388GFC1
No.3 power generating set : 600GFC1

Rated Power (KW) -
No.1 power generating set : 388
No.2 power generating set : 388
No.3 power generating set : 160

Rotating speed (r/min) -
No.1 power generating set : 750
No.2 power generating set : 750
No.3 power generating set : 750

Electric Furrent -
No.1 power generating set : AC (700A)
No.2 power generating set : AC (700A)
No.3 power generating set : AC (700A)

Rated voltage (V) -
No.1 power generating set : 400
No.2 power generating set : 400
No.3 power generating set : 400

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your requirements
and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

------------------------------------------------------------
Search words(for official use only) -
Floating Crane for Sale
Used Floating Crane for Sale
Floating Crane - 2005 built - For Sale
Floating Crane for Sale - 600 Ton
600Ton Afloat Crane for Sale
2005 built Floating Crane for Sale
--------------------------------------------------------------

Worldrigs ID: WR532

Platform Supply Vessel for Sale
DP2 Platform Supply Vessel for Sale - Newbuildings
MMC887 PSV FiFi 1 for Sale
Newbuildings DP2 PSV For sale

Classification : ABS +A1, (E) Offshore Support Vessel, +AMS, +DPS-2, +FFV Class 1

Other Compliances :
International Load Line Convention 1966,
International Tonnage Convention 1969,
COLREG 1972,
SOLAS 1974 with amendments (where applicable),
International Radio Communication Regulations,
MARPOL 73/78 (Annex I, II, IV, V, VI)

Principal Dimension :
Length O.A : abt. 88m
LPP : abt. 82.00m
Breadth MLD. : abt.19m
Design Draft : abt. 5m
Max Draft : abt. 6m
Deadweight : abt. 5145 Tonnes

Gross Tonnage : abt. 3601 Tonnes
Net Tonnage : abt. 1429 Tonnes
Deck Cargo : abt. 1000 Tonnes
Deck Strength : 5 Tonnes/sqm
Speed : abt. 14.3 knots at 100% MCR, 5m draft

Economic Speed: abt. 13 knots at 75% MCR
Deck Area : 1000 sqm
Complement : 52 men
Fuel Type : Gas Oil

Tank Capacity (Approximation) :
Potable F.W. : 1770 cbm
F.O. (Total) : 1100 cbm
Liquid Mud / Brine (S.G 2.4) : 680 cbm
Dry Bulk Cargo Tank (Cement/Baryte) : 400 cbm
Drill Water / Water Ballast : 1830 cbm
Methanol (SG 0.9) : 430 cbm

Bulk Handling System :
Suitable for Carriage of Cement/Baryte
Class : ABS
Total Capacity : 400 sqm  approx. (in 5 tanks)
Working pressure : 80 psi

Main Propulsion :
Main Propulsion – 2 x 2000 kW Fixed Pitch azimuth thruster c/w electrical motor.
Bow Thruster - 1 x 910 kW Tunnel Thrusters CPP c/w electric motor speed at
1800 rpm driven.
Retractable Thruster - 1 x 800 kW Retractable Thrusters CPP c/w electric motor speed
at 1200 rpm driven.

Power Plant :
1) Prime Mover(Diesel Engine) - 4 x 1825 kW Cummins Engine c/w generator, 480/3/60
2) Emergency / Harbour Generator - 1 x 350 kW approx, 480/3/60

Deck Machinery :
1) Anchor Windlass - Electro-Hydraulic driven, 2 Declutchable Drum, 2 Declutchable
cable lifter, 2 Fixed Warping End
Nominal Pull : 10 MT, 0 – 20m/min

2) Deck Crane - 2.0MT SWL at outreach 10.0M.
3) Others - 2 x Capstan (7.5mt pull) and 2 x Electric Mooring Winch(10mt pull)

Fire Fighting :
1) External Fire Fighting System – Class FiFi 1 having 2 in nos main fire pump
(1600cbm/h) driven by generator engine front PTO c/w 2 x Fire Monitors (1200m3/h) and
with fixed water spraying system as per classification rules.

2) Fixed Fire Protection System - Engine Room, Paint Store & Emergency Generator
Room installed with fixed CO2 Fire protection system

Navigation Equipment :
1) Echo Sounder
2) Radars
3) Voyage Data Recorder
4) Magnetic Compass
5) Auto Pilot
6) AIS
7) Weather Facsimile Receiver
8) Doppler Speed Log
9) Ship Security Alert System

Communication Equipment :
1) GMDSS for Area A3
2) PA/Talk back
3) Auto Telephone System

Dynamic Position System :
Dynamic positioning system according to ABS DPS-2 c/w with 2 off DP operator
stations, 1 off cJoy Operating Terminal, 1 off cJoy Wing Terminal(Portable), 2 off
Gyrocompass, 2 off Wind sensors, 2 off Motion reference units, 1 off Spotbeam, 1 off
RADius Position reference system, 2 off DGPS, 2 off UPS, 2 off Alarm and Event Printer.

The following basic operational modes are included :
• Joystick Mode
• Auto Pilot Mode
• Auto Heading Mode

Accommodation :
Fully Air-Conditioned c/w hot water heating and air distribution system. One off
electrical heater to be installed in cabins.
16 x 1 man cabin – 16 men
10 x 2 men cabin – 20 men
4 x 4 men cabin – 16 men
Total – 52 men
Dispensary – 1 men

Spare Parts : Class Standard requirements applied.

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
--------------------------------------------------------------------------------------------------
Search words (for official use only) :
Platform Supply Vessel for Sale
DP2 PSV FiFi 1 for Sale - Newbuildings
MMC887 Platform Supply Vessel
Newbuildings PSV-DPII FiFi 1 for Sale
MMC887 PSV for Sale
-----------------------------------------------------------------------------------------------------

Worldrigs ID: WR2758

Foremost DR-24 Drilling Rig for Sale
Drilling Rig - Foremost DR-24 - For Sale

Model : DR-24 Drill Rig
Manufacturer : Foremost Barber
Year : 2001
Condition : Used

Description :

2001 Foremost DR-24 Drill Rig
Mounted on 2001 Freightliner Truck
Caterpillar C-15 Diesel Engine (rated 500 HP)
4,100 Hours as of 10/16/20
Atlas Copco 900 cfm / 350 psi Air Compressor
24” Diameter Dual Rotary Power Head
Set up for 2-7/8" IF Drill Rod and 6” Beco Rod
4 piston FMC Bean water injection pump
Jaws 6, 8, 10, 12, 14, 16, 18, 20, 24 inch
Welding (Cage) Clamp 6, 8, 10, 12, 14, 16, 18, 20, 24 inch
Divertor for 4-1/2 inch Drill Rod with adaptors for 6, 8, 10,
12 inch casings
Divertor for 10-3/4 inch drill rod with adaptors for 12, 14, 16, 18,
20, 24 inch casings
Drive Shoes 6, 8, 10, 12, 14, 16, 18, 20, 24 inch
24 - 4-1/2 inch x 20 ft x 2-7/8 IF thread drill rods
6 - 10-3/4 x 20 ft x 6-5/8 Beco thread drill rods
1 – 10-3/4 x 15ft x 6-5/8 Beco thread drill rod
1 - 10-3/4 x 10ft x 6-5/8 Beco thread drill rod
2 – 10-3/4 x 5ft x 6-5/8 Beco thread drill rods
New Miller Welder
1 – Petol wrench setup for 4-1/2" Inch drill rod and 6 inch hammer
1 – Petol wrench setup for 6-inch drill rod and 8 inch hammer
6” IR QL60 Drill Hammer with 4-1/2” x 15ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 15ft lead steel with bit
IR QL120 Drill Hammer with 10-3/4" lead steel and subs and
12” bit 12ft - QL120 Bit
2-7/8" IF x 4-1/2" centralizer drill rod for 10" inch casing
24" Inch over the hammer centralizer for QL120 hammer
Cyclone diverter
5 Inch Concrete Discharges Hoses 15 ft
5 Inch Concrete Discharges Hoses 25 ft

Location : USA

Price & terms : Please enquire using the email form below.        

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Foremost Barber DR-24 Drilling Rig - 2001 Built for Sale
Used Drilling Rig - Foremost Barber DR-24
2001 Built Foremost Barber DR-24 Drilling Rig
Land Drilling Rig - Foremost Barber - For Sale
Foremost Barber Used Drilling Rig for Sale in USA
-------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1417

CME 55 Drilling Rig for Sale
Drilling Rig - CME 55 - For Sale

Model : 55 Drill Rig
Manufacturer : CME Drill
Year : 1978
Condition : Used

Description :

CME 55 Drill Rig - Serial Number: 130085
Moyno-type Water Pump
Cathead
Winch
Auto Hammer Driver installed by CME
Ford Gas Deck Engine
Hydraulic operator controls
Hydraulic Leveling Jacks
Mounted on single-axle 1978 International 1600 truck - VIN: D0512HHB33188
Gas engine
manual transmission

Location : USA

Price & terms : Please enquire using the email form below.        

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
1978 Built CME 55 Drilling Rig for Sale
Used CME 55 Drilling Rig for Sale
CME 55 Drilling Rig - 1978 Built for Sale
1978 Built CME 55 Used Drilling Rig for Sale
CME 55 Drilling Rig for Sale in USA
-------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2079

70TBP AHT for sale
45M Used Anchor Handling Tug for Sale
2009 built AHT for sale

General
Year Built : 2009
Class Bureau Veritas
Notation : I HULL MACH, Tug; Special Service- Anchor Handling
Vessel Unrestricted Navigation
GRT / NRT : 874/262
Deadweight : 539 MT

Dimensions
Length Overall : 45.00 m
Length Waterline : 43.50 m
Breadth Moulded : 12.60 m
Depth Moulded : 5.30 m
Draft (max) : 4.50 m

Performance
Maximum Speed : 13.0 knots at 15 MT/24 hrs
Economical Speed : 10.0 knots at 10 MT/24 hrs
Type of Fuel : Marine Gas Oil
Endurance About : 40 days

Cargo Capacities
Fuel Oil : 486 m³
DW/SWB : 77 m³
Fresh Water : 266 m³
Freezer/Chiller : 30 m³
Deck Cargo : 100 MT
Deck Strength : Uniform 5 T/m² main deck & 15 T/m² stern
Clear Deck Area : 200 m²

Radio & Navigation Equipment
GMDSS (For Area 3) : 1 x Furuno RC-1800 IT
SSB : 1 x Furuno FS 2570C
VHF : 2 x Furuno FS 8800S/ Icom IC-M422
Radar : 1 x Furuno FAR 2117/ 1942 Mark 2
Echo Sounder : 1 x JRC Model JFC-582-200 Khz
Gyro Compass : 1 x unit at main steering position at sterring gear
Magnetic Compass : 1 x unit standart suara model MR-150
Speed Log : 1 Doppler log JRC Model JLN -205
Auto Pilot : 1 unit Syncronized to gyro steering compass
Navtex Receiver : 1 x Furuno NX 700
GPS Navigator : 2 x Furuno GP-150
AIS : 1 x Furuno FA-150
SART : 2 x Mcmurdo S4
EPIRB : 1 x Mcmurdo E5
Portable VHF (GMDSS) : 3 x Jotron TR20

Deck Equipment
Anchor Windlass c/w bow : 1 x electro-hydraulic 24 MT
Anchors & Chain :
2 x Stockless Anchor 1160 kg each;
2 x 605m x 34mm Ø U2 Stud Link Chains

Anchor Handling / Tugger Winch :
1 x electro hydraulic; double drum waterfall type
Line Pull at 1st Layer :
150T @ 6m/min (1st speed)
75T @ 12m/min (2nd speed)
12T @ 36m/min (2nd speed)

Brake Holding : 225 MT at 1st layer
Drum Capacity : 1000m (L) x 58 mm (Dia) SWR
Bollard Pull : 70.0T6
Tugger Winch : 2 x electro hydraulic 10T@ 15 m/min
Capstan : 2 x electro hydraulic 5T@ 15 m/min
Towing Pin : 2 x SWL 100T
Shark Jaw : 1 x SWL 200T
Stern Roller : 1 x 1500mm Ø x 4200 mm width – SWL 200T

Life Saving Equipment
Life Rafts : 1x25 men & 1x20 men, SOLAS compliant
Rescue Boat c/w Davit :
1 x 6 men, 20HP c/w outboard engine, SOLAS compliant
All other life saving appliances as per SOLAS requirements

Propulsion System
Main Engines :
2 x Niigata 6MG28HX, 2500 BHP/ 1823 KW
Total: 5000 BHP/ 3646 KW

Auxiliary Engines : 3 x 300 KW - 415V, 3PH, 50HZ
Emergency Generator : 1 x 80 KW - 415V, 3PH, 50 HZ
Bow Thruster : 1 x 441 KW
Propellers : 2 x FPP
Steering Gear System : 2 x Electro Hydraulic
Rudder : 2

Fire-Fighting Equipment & Anti-Pollution Equipment
External
Equivalent to 1/2 FiFi
Fire pump : 1 x 1500 m³/hr @140m head

Internal
CO² System : Engine Room
Fire Fighting Equipment : Fully compliant with SOLAS requirements
Emergency Fire Pump : 1 x 30 m³/hr @ 60m head
Water Mist System : Engine Room

Accommodation (All cabins are fully air-conditioned)
Berths :
4 x 1 berth cabins = 4
2 x 2 berth cabins = 4
4 x 4 berth cabins = 16
Total :  24

Dispersant System
Fresh Water Maker : Nil
Oily Water Separator : 1 x 1.2 m³/hr
Sewage Treatment Plant : 5.5 m³/hr

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where
needed.

The details mentioned above are believed to be accurate but are not guaranteed.
----------------------------------------------------------------------
Search words (for official use only) -
45M Anchor Handling Tug for Sale
Used 2009 built  Anchor Handling Tug for Sale
70TBP AHT for sale
45M Used Anchor Handling Tug for Sale
2009 built AHT for sale
Used 45M AHT for sale
Used 70TBP Anchor Handling Tug for Sale
-------------------------------------------------------------------------

Worldrigs ID: WR1257

Landing Craft for Sale
23M Landing Craft for Sale - Newbuilt
Newbuilt Landing Craft for sale - Built in Australia

Particulars
Length O.A : 23.75m
Beam (mld) : 7.80m
Depth (mld) : 1.60m
Survey : 2C - 12 passengers + 3 crew

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Landing Craft  - Newbuilt for sale
23M Landing Craft - Built in Australia - For sale
23m Landing Craft for sale - Built in Australia
New 23M Landing Craft
Newbuilt Landing Craft in Australia for Sale
---------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR880

Crane Barge for Sale
Used Derrick Barge for Sale
Crane Barge for Sale - Net tonnage 616mt

Specifications

Type : Derrick Barge
Classification : *100 A5 M Barge,Crane Barge

Dimensions
Nett tonnage : 616 mt
GRT : 2055 mt
Length : 73,09 m
Beam : 21,96 m
Depth of hull : 5,50 m
Free deck area : 19m x 35m
Draft empty : 2,40m

Storage Capacity
Fuel oil : 360 cbm
Processed oil : 2*400 cbm
Potable water : 40 cbm

Prime Mover
Engine : 3off GM12v71

Block Capacities
Main : 250 mt
Auxillary : 50mt
Whip Line : 25mt

Main Engine Room / Primary Equipment
Power generation :
2* 345kVa -60Hz
1* 68 kVa - 60Hz

Ballast system : 2* 400tons/h
Accomodation : 10 persons
Anchor winches : 2* tripledrum Skagit RB90

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
---------------------------------------------------------------------------------------------------
Search words(for official use only) -
Crane Barge for Sale
Over 73m in Length Crane Barge For Sale
Derrick Barge for Sale
Barge for Sale - Length 73.09m
Crane Barge for Sale - 10 persons accomodation
----------------------------------------------------------------------------------------------------

Worldrigs ID: WR2454

CABOT 1200 Trailer Mounted Drilling Rig for Sale
1200 hp Trailer Mounted Drilling Rig for Sale 

Description :

Drawworks :
Ingersoll-Rand (IRI) 1500 series trailer mounted rig with
IRI 2550 mechanical drawworks with twin parmac
V-80 hydromatic brakes

Rotary Table :
CE 271/2 rotary, independently driven by one (1) hydraulic motor

Engines and Generators :
Two (2) CAT 3412 DITA electronic controlled diesel engines rated
750 HP each at 2100 RPM with ALLISON model 56600 transmissions,
complete with hydraulic controls, powering the 1500 HP drawworks.

Overhead String :
300 ton, 5 sheave, travelling block and one 350 ton hook.
11/4 drilling line.

Mast :
IRI 136' mst with 700,000# hookload-mast has capability to 
accommodate a 700 hp top drive

Substructure :
IRI 22' telescoping substructure rated at 700,000# rotary load
with 400,000# simultaneous setback

Mud Tanks :
Two (2) tanks, 800 BBL

Solids Equipment :
Two SWACO AWD Linear motion shale shakers, SWACO degasser, 
SWACO 2 cone desnader, SWACO 12 cone desilter, and flour 
mud agitators

Mud Pumps :
Two (2) HH model F-1000 triplex mud pumps. Powered by Caterpillar 
model D399TA Diesel engines. Suctions charged by A6"x5", series 
178 centrifugal pumps and an EMSCO style discharge pulsation 
dampeners.

Trip Tank :
100 BBL W/ (2) 50 BBL compartments W/ 2" x 3" centrifugal pump

Well Control Equipment :
One (1) CIW 13 5/8 5M double BOP W/hydril 13 5/8M annular,

Accumulator :
Koomey Type 8-0 (5) five-station closing unit, with (16) 11 gallon
accumulator bottles, (1) triplex pump, (2) air pumps with 120:1 ratio

Catwalk :
Steel deck 18"H

Generator/Utility House :
Two (2) caterpillar 350 KW AC generators, powered by CAT C-15 
diesel engines W/electric start, air compressors and MCC panel

Water Tank :
400 BBL complete W/(2) 3" x 2" series 250 centrifugal water pumps
powered by 20 hp AC electric motors

Fuel Tank :
10,000 gallon W/(2) roper 3 hp fuel transfer pump

Drillers Doghouse :
Drillers Doghouse 8' x 26'

Auxiliary Equipment :
(2) H5UL air hoist, VARCO SSW 30 hydraulic drill pipe spinner

Instrumentation :
Weight indicator, W/tong line pull, pump pressure & rotary torque
gauges, type "D" 5,000 PSI mud pressure gauge

Wireline Machine :
Mathey retriever W/15,000' OF .092 wireline

Well Site Trailers :
Rig manager trailer 12'x56', crew change house

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us anemail to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------
Search Words (for official use only) :
CABOT 1200 Trailer Mounted Drilling Rig for Sale
1200 hp Trailer Mounted Drilling Rig for Sale
Trailer Mounted Drilling Rig for Sale in USA
CABOT 1200 Drilling Rig for Sale
Used Trailer Mounted Drilling Rig for Sale
---------------------------------------------------------------------------------------------------

Worldrigs ID: WR369

Ingersoll-Rand RD20 II Used Drill Rig for Sale
1993 Built Ingersoll-Rand RD20 II Drill Rig

Model : RD20 II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1993
Condition : Used

Description

1993 Ingersoll-Rand RD20 Range II Drill Rig - S/N: 3987
Cummins KTA19 Diesel Deck Deck Engine @ 600 HP
7 Rod Carusel
Cat 2520 water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1993 Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
VIN number: PGV84002
Note: No Air Compressor on board as of now (was a IR 1050/350)

Location : USA
 
Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

-------------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Ingersoll-Rand RD20 Range II Drill Rig for Sale
Used Ingersoll-Rand RD20 Range II Drill Rig for Sale
Ingersoll-Rand RD20 Range II Drill Rig in USA
Ingersoll-Rand Used Drilling Rig for Sale
1993 Built Ingersoll-Rand RD20 Range II Drill Rig
-------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1326

ASME LPG Storage Tanks for Sale
Used AMF Beaird ASME LPG Vessel for Sale
1966 Built - 30,000 Gallon Used ASME LPG Tanks for Sale

Description
Quantity : 2
Manufacturer : AMF Beaird
Year : 1966
Dimensions : 132" OD x 47' OAL
Pressure : 250 psi
Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.


         

---------------------------------------------------------------------------------------------------------
Search words(for official use only) :
ASME LPG Storage Tanks for Sale
1966 Built AMF Beaird ASME LPG Vessel for Sale
30,000 Gallon Used ASME LPG Tanks - 1966 Beaird for Sale
AMF Beaird ASME LPG Tanks for Sale - 1966 Built
30,000 Gallon Capacity ASME LPG Storage Tanks for Sale
2 Used AMF Beaird ASME LPG Vessel for Sale
----------------------------------------------------------------------------------------------------------

Worldrigs ID: WR125

2002 Built Harbour Tug for sale

Description
Year Built : Oct 2002
LBD : 12.8x4.7x2.0m
M/E : MHI(Mitsubisi Heavy Industry) S6R2F-MTK3 900psx2）
A/E : 30KWx2

GPS/RADAR equipped
bridge controller is equipped
Upper hull is Aluminium Alloy

Inspectable Place : West Japan

Details above are given in good faith with no warranties expressed or implied.

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------
Search words(for official use only) : 
Tug for sale, 
Harbour Tug for sale
2002 Built Tug for sale
Tug 2002 Built for sale
-------------------------------------------------

Worldrigs ID: WR1216

National OS-105 Hydraulic Pedestal Crane for Rent or Sale
Hydraulic Pedestal Crane for Rent
Marine Offshore Crane for Rent or Sale
45 ton Marine Offshore Crane for Sale

Description
45 ton Marine Offshore Crane
Hydraulic Pedestal Crane
Pneumatic Control
Crane being refurbished to new 100 ft boom
Main Hoist 26 tons at 40ft dynamic lift
Fast Line – 10,000 lbs
Diesel Engine

Terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------------
Search words (for official use only) :
National OS-105 Hydraulic Pedestal Crane for Rent or Sale
45 ton Marine Offshore Crane for Sale
National OS-105 Hydraulic Pedestal Crane - 45 Ton
Used Marine Offshore Crane - 45 ton
Used Hydraulic Pedestal Crane - For Rent or Sale
Hydraulic Pedestal Crane - 45 Ton
Marine Offshore Crane for Rent or Sale
Used National OS-105 Hydraulic Pedestal Crane
Hydraulic Pedestal Crane for Rent
--------------------------------------------------------------------------------------------------

Worldrigs ID: WR2227

Witchtex R-4 Trailer Mounted Drilling Rig for Sale
Trailer Mounted Land Drilling Rig for Sale

Description :

Trailer Mounted Rig:
3-Axle Back-In Trailer w/Rotary Beams
6) Hydraulic Leveling Jacks
1) Folding Walkways
1) Safety Rails and Stairways, 11R24.5 Tires, Steel Disc Wheels

Drawworks:
1) D/D Draw works, Groove F/1” Line
1) Makeup and Breakout Catheads
1) Driller’s Console w/Air Controls
1) SGL –Engine Compound P/B Detroit 8V-92 Diesel Engine
1) Allison Torque Converter 

Mast:
1) 65’H Hydraulic Raised Mast Reported 180,000 Hook Load
1) Crown Block Assembly
1) Mackissick Block/Hook Combo w/(3) Sheaves F/1” Line,
1) Baash-Ross Type DBM-330 100-Ton Block/Hook Combo w/(3) Sheaves
1) Oilwell 60-C Swivel
1) Gardner-Denver 17 ½” x 44” Rotary Table w/Split Master Bushing
1) Standpipe and Manifold
1) Rotary Hose
1) 4 ¼” Sq. Kelly
1) Baash-Ross 4 ¼” Sq. Kelly Drive Bushing

Mud Pumps:
1) Ameriam 550 6”X14” Duplex Mud Pump w/GH Mattco Fluid End,
Quick-Change Caps, Oteco 2” Shear Relief Valve Type D Pressure Guage,
Hydril K-20-5000 Pulsation Dampener, Rod Cooling Pump, Bull Wheel,
Belt U-12 Detroit Diesel Engine W/Electric Starter Radiator,
Gauges Pump Drive Assembly, Master Skidded

1) National C-250 6X15 with Mattco Fluid End, powered by a
CAT 3406 Diesel Eng W/Electric Starter Radiator, Gauges Pump
Drive Assembly, Master Skidded

Gen Set:
1) 250 KW Light Plant powered by a 3306 CAT Diesel Engine
1) Ingersoll Rand Stand-by Air Compressor
1) Quincy Air Compressor
Top Dog House:
1) 17’W x 16’L Driller’s House w/Round Top, Knowledge Box,
Bench Storage, Parts Bins, (3) Lockers, Heater, Fluorescent Lights,
Skidded
1) Drillograph Single Pen Recorder

Fuel and Water:
1) 18’Dia. x 16’L Approx. 5000 Gal. Fuel Tank, Skidded
1) 14’3”H x 7’6 ½”W x 38’L 220 BBL Crimped Steel Water Tank, Skidded

Miscellaneous:
1) Set of BJ Type C Tongs
1) Set of 2 1/8” x 96” L Elevator Links
1) Web Wilson 150 Ton 4 ½” BN CL Drill Pipe Elevator

1) Lot of (1) 72”H and (1) 62”H x 28’ L Triangular Pipe Racks w/Catwalk Tray
1) 36”H x 7’5”W x 36’L Pipe Tub
1) 7’5”W x 34’L Drill Collar Skid

1) Assorted Rig Hoses, Piping and Stairways
1) 10” 3000 PSI Regan Annular

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Witchtex R-4 Trailer Mounted Drilling Rig for Sale
Trailer Mounted Land Drilling Rig for Sale
Witchtex R-4 Trailer Mounted Used Drilling Rig for Sale
Witchtex R-4  Drilling Rig for Sale in USA
---------------------------------------------------------------------------------------------------------------