Oil & Gas land drilling rigs for sale, Land drilling rigs for sale
Home Biofuels Oil & Gas Directory Glossary Training News Newsletter Events LDPE Recycling Contact Water Well Rigs
Land Drilling Rigs Jackup Rigs Oilfield Container Camps Offshore Accommodation Steel Houses Mini Submarines Oil & Gas Equipment Marketplace
Home Biofuels Oil & Gas Directory Glossary Training News
Newsletter Events Contact Water Well Rigs Land Drilling Rigs
Jackup Rigs LDPE Recycling Oilfield Container Camps Crude Oil Price History
Steel Houses Mini Submarines Oil & Gas Equipment Marketplace
Home Jackup Rigs LDPE Recycling
News Water Well Rigs Land Drilling Rigs
Mini Submarines Events Steel Houses
Oilfield Container Camps Oil & Gas Directory
Oil & Gas Equipment Marketplace Contact


 

If you cannot find the new or used offshore rigs, vessels or equipment of any type, size or make that you are looking for, please send us an email to and we shall offer you.


 

If you cannot find the new or used offshore rigs, vessels or equipment of any type, size or make that you are looking for, please send us an email to and we shall offer you.


Linear Winch KTC 240 for Sale or Charter
Worldoils Oil, Gas and Offshore Marketplace    

Equipment ID   : 1051
Equipment name   : Linear Winch KTC 240 for Sale or Charter
Category   : Winches
Specifications   :

Linear Winch KTC 240 for Sale or Charter
Winch for Sale - KTC 240


Scope of supply :
Equipment :
  1 Continuous linear winch KTC-240, 240 tonnes @ 1.3 m/min
  2 Hydraulic control modules, itegrated on the KTC-240
  1 PLC control cabinet for the winch command
  1 Control console
Factory testing of the unit
Commissioning and start-up spare parts
Painting and Protective coatings
Tagging
Documentation
DNV witness certificate
Weighing
Preservation, Packing & Marking
Delivery FCA Paris workshop
Operator training
Commissioning and start-up assistance

General characteristics :
Pulling capacity :
240T @ 0 to 1.3 m/min
115T @ 0 to 2.4 m/min
Operating temperature :
-15°C <T< +50°C (linear winch)
+5°C <T< +40°C (control cabinet and console)
Storage temperature :
-20°C <T< +60°C (linear winch)
-20°C <T< +60°C (control cabinet and console)
Environment : marine, on open deck
Hazardous area : zone 1 IIB T4

KTC-240 Linear winch :
The blocks are guided along 2 parallel U rails with stainless steel
removable supports and self lubricated interchangeable bearings.
For weight reasons, the frame is built in 2 seperate bolted parts,
and the gripped are removable from the frame.
The linear winch is attached working hanging or rested, horizontally
on deck foundations (yard supply).
Continuous motion.
Strong construction frame.

Characteristics :
Pull-in capacity (SWL) : 240 metric tones (to be tested during fat)
Speed at up to 240T : 1.3 m/min continuous and adjustable
Speed at up to 130T : 2.4 m/min continuous and adjustable
Oil consumption at maximum speed : 2 × 120 l/min
Pressure at SWL : 290 barg
Back tension at SWL : not required
Jack stroke : 950 mm
Wire rope diameter : 72 mm (with changeable inserts)
Maximum cable dia : 89 m (3" 1/2)
Overall dim : 2.24 m (W) × 8.10 m (L) × 0.80 m (H)
Weight : 23.5 tonnes = 2 ×(6.95 t + 4.8 t)
Design life : 25 years operation

The winch shall be capable of hauling-in and paying-out under any load,
in automatic and manual mode, in continuous operation.
It also includes 4 guide rollers (2 horizontal and 2 vertical ones) for the
back side (low tension side).

Hydraulic control modules :
The linear winch frame includes 2 hydraulic modules (one for each gripper)
for the synchronization, control and safety of the grippers of the linear winch.
They are mounted and piped on the frame itself. They are suitable to operate
into a hazardous area (Atex zone 1).

They are equipped with an integrated line-pull limitation. A potentiometer
adjusts the line-pull between 0 and 100%, and a software preset adjusts
the 100% betweem 50 t and 240 t.

For the powering of the linear winch, an external and independent
2 × 75 kW. HPU in LS control and with 2 × 130 l/min @ 310 barg. The HPU
has 4 outlets on each pump : pressure, return, drain and LS. The linear
winch must be fitted to this system for male connections (hydraulic inlet
power to the linear winch).

Required oil power for the linear winch should be as follows :
two identical and independent supplies (1 for each gripper) of  3 lines
each, with each the following utilities requirements :
P with 130 l/min at 310 bar per gripper
R with 160 l/min at ≤ 5 bar per gripper
D with 15 l/min at ≤ 1 bar per gripper
LS connections

Fittings internal on the linear winch :
On the main connections/ tubing it's require with SAE flanges.
On the smaller connections/ tubing where SAE flange won't
be used (10 and 12 mm tubes) it's required with parker EO2
fittings.
The hydraulic connections shall be assembling on one place
(scot plate) for each gripper.
Connections shall be as follow :
Pressure : 5/4" bsp male
Return : 1.1/2" bsp male
Drail : 3/4" bsp male
LS : 1/4" bsp male

Local control cabinet & panel :
The winch is supplied with the PLC control and command,
necessary for its full control and located remotely to the
winch. It is suitable for hazardous area (Zone 1)

a) PLC Cabinet :
The PLC cabinet is supplied loose, to be mounted into a
weather protected control container

It will include :
EExd cabinet
Power supply 230 v - 50/60 hz delivered with electrical supply cable
H07RN-F rubber cable 2,5G3 (2,5 mm2 with 2 conductors + earth)
PLC, Siemens S7
I/O cards
Profibus card
Terminals block

This PLC is used to control the linear winch functions (in automatic
and manual operations).

There is also a Profibus port available for connection with the HPU PLC.
It may be used for interfacing the HPU commands (on-off) and to monitor
the HPU faults and alarms.

Control panels :
It will include the following :
316L stainless steel panel, 3 mm (385 mm (H) × 540 mm (W)
Synoptic panel
Control buttons & lamps
Linear winch
Speed potentiometer
Line-pull potentiometer
Button manual / 0 / automatic
Push-buttons for manual speed control
Wedges opening controls
Pull / pay-out selector
Start / stop
Stop buzzer / fault reset
Lamp test
Emergency stop
Pilot lamps :
5" 1/2 Exe screen for cable tension, speed & length displays,
status and faults & alarms displays, and calibration set & preset inputs.
Connection block

Party verification :
This order includes a 3rd party FAT witness certificate from DNV.
It includes :
Witness of pressure tests (hydraulic cylinders, piping)
Witness of FAT
Lifting pad-eyes certificate DNV 2.7.3 for offshore handling.
Drop tests and lifting on 2 points are not provided.
Manufacturing documentation review
FAT witness

Protection :
This equipment is designed to be operated on open deck.

Painting : A 3 coating marine paint, 320 µ is included. It will be according to Norsok
M501 RAL 1007 system 1.
Concerning the piping on the winch, it is CS made, and the manifold blocks
have BSP ports for fitting quick release couplings.

Quality control :
Quality control is carried out according to ISO 9001-2008.
An ITP is issued during the first month after contract, and progress plan and
reports are regularly controlled.

Documentation :
All the necessary documentation ( according to Norsok Z-015)
related to the design, fabrication, testing, inspection and maintenance of the riser
pulling equipment will be provided

This will include :
Design drawlings and as-built GA drawings
Material certificates and test reports
Equipment and instrumentation data sheets
Traceability records of raw materials such as steel plate, fasteners, pins
and shafting from Kley France sub-vendors.
Welding procedures (WPS's), Procedure qualification reports
(PQR's), and welder qualifications
NDE procedures, records, and qualifications of NDE personnel
Non-conformance/discrepancy reports and final dispositions
Dimensional control reports
Weight and centre of gravity data sheets and certificates
Kley France certificate of compliance
DNV certificates
Installation and preservation procedures
Operasjon and maintenance manuals
Lists of available spare parts

Sale/charter rate & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

The details mentioned above are believed to be accurate but are not guaranteed.

----------------------------------------------------------------------------------------------------
Search words :
Linear Winch for Sale
Linear Winch KTC 240 for Sale or Charter
KTC240 Linear Winch for Charter
Winch for Sale - KTC 240
Linear Winch KTC 240 for Sale
Linear Winch for Charter
Winch for Sale or Charter

---------------------------------------------------------------------------------------------------

     
Worldoils Oil, Gas and Offshore Marketplace
Worldoils Oil, Gas and Offshore Marketplace - Linear Winch KTC 240 for Sale or Charter
Images
 
Linear Winch for Sale';
 
Linear Winch KTC 240 for Sale or Charter';
 
KTC240 Linear Winch for Charter';
 
Winch for Sale - KTC 240';
 
Linear Winch KTC 240 for Sale';
 

Send an email to Intersolve
Note: Fields marked by (*) are mandatory.
Email to:  Intersolve
For equipment:  Linear Winch KTC 240 for Sale or Charter
Category:  Winches
Your name:  *
Your company:  *
Your email address:  *
Your phone no.:  *
Your message:  *
Security code:
* (Use capital letters only)

 

The information contained herein is believed to be accurate but has not been verified. This equipment is subject to prior sale and sold “where-is as-is” with no warranties from Worldoils Pte Ltd or the Seller expressed or implied.
Worldoils Oil, Gas and Offshore Marketplace    Worldoils Oil, Gas and Offshore Marketplace


Vessel Monitoring Software
Offsore Rig Monitoring Software
Mobile Hospitals
Field Hospitals
LDPE Recycling

Live Monitoring of Ships and rigs

Oilfield Container Camps

Remote ship Bunker GFuel Monitoring

Mini Submarine

Ring Maintenance Software

Mining Container Camps
Offshore Jackup Rigs
Land Drilling Rigs
Barge  Swamp Rigs

Oil & Gas Industry Machinery & Equipment Marketplace
Atlas Copco RD20 Range III Drilling Rig - For Sale
Landing Craft Tank - 80 Meters - For Sale
Landing Craft 34 Meters Passenger Ferry - For Sale
Self Propelled Oil Barge - 1000 KL - For Sale
Ingersoll-Rand TH60 Drilling Rig - For Sale
Atlas Copco RD20 Range III Drilling Rig - For Sale
Atlas Copco T30 Power ROC Crawler Drilling Rig - For Sale
Chain Stoppers - For Rent
Atlas Copco T4BH (Blast Hole) Drilling Rig - For Sale
Chain Hoists and Trolleys - For Rent
Driltech T25K2W Drilling Rig - For Sale
Drilltech T25K2W Drilling Rig - For Sale
Offshore Anchor Chain - For Rent
Subsea Buoys - For Rent
Atlas Copco D65 Flexiroc Drilling Rig - For Sale
Towing Brackets for Rent
Hose & Reel Equipment for Sale
Double Bollards - For Rent
Taylor RT 5000M Trailer Mounted Drilling Rig - For Sale
Used Blocks - For Rent
Subsea equipment baskets - For Rent
Used Barges - For Rent
Aanchors for Rent
A-frames - For Rent
LPG Bullet Tanks - For Sale
Worldoils Land Rigs Market
1000hp Land Drilling Rigs
1500hp Rotary Land Drilling Rigs
2000hp Rotary Land Drilling Rigs
3000hp Rotary Land Drilling Rigs
Workover Land Rigs
Carrier Mounted Land Drilling Rigs
Trailer Mounted Land Drilling Rigs
Worldoils
Events Subsystem
Oil, Gas & Biofuels Events
25 - Sep - 2023 : Midland
SPE Permian Basin Energy Conference [Map]

25 - Sep - 2023 : Houston, Texas
Turbomachinery & Pump Symposia [Map]

26 - Sep - 2023 : Houston
Breakbulk Americas 2023 [Map]

26 - Sep - 2023 : Hanoi
ASIA-TECH – Asia Refining & Petrochemical Tech Forum [Map]

26 - Sep - 2023 : Houston
Onshore Wellsite Facilities Congress 2023 [Map]

26 - Sep - 2023 : Houston
Sustainable Production & Chemicals Optimization 2023 [Map]

27 - Sep - 2023 : Maputo
The 8th Mozambique Gas & Energy Summit & Exhibition [Map]

27 - Sep - 2023 : Boston
US Hydrogen & Fuel Cells Energy Summit [Map]

27 - Sep - 2023 : Houston
Immersive Technology for Oil & Gas Summit [Map]

2 - Oct - 2023 : Abu Dhabi
ADIPEC 2023 [Map]


 

 

If you cannot find the new or used offshore rigs, vessels or equipment of any type, size or make that you are looking for, please send us an email to and we shall offer you.

Linear Winch KTC 240 for Sale or Charter
Worldoils Oil, Gas and Offshore Marketplace    
Worldoils Oil, Gas and Offshore Marketplace

Equipment ID   : 1051
Equipment name   : Linear Winch KTC 240 for Sale or Charter
Category   : Winches
 
Specifications  :

Linear Winch KTC 240 for Sale or Charter
Winch for Sale - KTC 240


Scope of supply :
Equipment :
  1 Continuous linear winch KTC-240, 240 tonnes @ 1.3 m/min
  2 Hydraulic control modules, itegrated on the KTC-240
  1 PLC control cabinet for the winch command
  1 Control console
Factory testing of the unit
Commissioning and start-up spare parts
Painting and Protective coatings
Tagging
Documentation
DNV witness certificate
Weighing
Preservation, Packing & Marking
Delivery FCA Paris workshop
Operator training
Commissioning and start-up assistance

General characteristics :
Pulling capacity :
240T @ 0 to 1.3 m/min
115T @ 0 to 2.4 m/min
Operating temperature :
-15°C <T< +50°C (linear winch)
+5°C <T< +40°C (control cabinet and console)
Storage temperature :
-20°C <T< +60°C (linear winch)
-20°C <T< +60°C (control cabinet and console)
Environment : marine, on open deck
Hazardous area : zone 1 IIB T4

KTC-240 Linear winch :
The blocks are guided along 2 parallel U rails with stainless steel
removable supports and self lubricated interchangeable bearings.
For weight reasons, the frame is built in 2 seperate bolted parts,
and the gripped are removable from the frame.
The linear winch is attached working hanging or rested, horizontally
on deck foundations (yard supply).
Continuous motion.
Strong construction frame.

Characteristics :
Pull-in capacity (SWL) : 240 metric tones (to be tested during fat)
Speed at up to 240T : 1.3 m/min continuous and adjustable
Speed at up to 130T : 2.4 m/min continuous and adjustable
Oil consumption at maximum speed : 2 × 120 l/min
Pressure at SWL : 290 barg
Back tension at SWL : not required
Jack stroke : 950 mm
Wire rope diameter : 72 mm (with changeable inserts)
Maximum cable dia : 89 m (3" 1/2)
Overall dim : 2.24 m (W) × 8.10 m (L) × 0.80 m (H)
Weight : 23.5 tonnes = 2 ×(6.95 t + 4.8 t)
Design life : 25 years operation

The winch shall be capable of hauling-in and paying-out under any load,
in automatic and manual mode, in continuous operation.
It also includes 4 guide rollers (2 horizontal and 2 vertical ones) for the
back side (low tension side).

Hydraulic control modules :
The linear winch frame includes 2 hydraulic modules (one for each gripper)
for the synchronization, control and safety of the grippers of the linear winch.
They are mounted and piped on the frame itself. They are suitable to operate
into a hazardous area (Atex zone 1).

They are equipped with an integrated line-pull limitation. A potentiometer
adjusts the line-pull between 0 and 100%, and a software preset adjusts
the 100% betweem 50 t and 240 t.

For the powering of the linear winch, an external and independent
2 × 75 kW. HPU in LS control and with 2 × 130 l/min @ 310 barg. The HPU
has 4 outlets on each pump : pressure, return, drain and LS. The linear
winch must be fitted to this system for male connections (hydraulic inlet
power to the linear winch).

Required oil power for the linear winch should be as follows :
two identical and independent supplies (1 for each gripper) of  3 lines
each, with each the following utilities requirements :
P with 130 l/min at 310 bar per gripper
R with 160 l/min at ≤ 5 bar per gripper
D with 15 l/min at ≤ 1 bar per gripper
LS connections

Fittings internal on the linear winch :
On the main connections/ tubing it's require with SAE flanges.
On the smaller connections/ tubing where SAE flange won't
be used (10 and 12 mm tubes) it's required with parker EO2
fittings.
The hydraulic connections shall be assembling on one place
(scot plate) for each gripper.
Connections shall be as follow :
Pressure : 5/4" bsp male
Return : 1.1/2" bsp male
Drail : 3/4" bsp male
LS : 1/4" bsp male

Local control cabinet & panel :
The winch is supplied with the PLC control and command,
necessary for its full control and located remotely to the
winch. It is suitable for hazardous area (Zone 1)

a) PLC Cabinet :
The PLC cabinet is supplied loose, to be mounted into a
weather protected control container

It will include :
EExd cabinet
Power supply 230 v - 50/60 hz delivered with electrical supply cable
H07RN-F rubber cable 2,5G3 (2,5 mm2 with 2 conductors + earth)
PLC, Siemens S7
I/O cards
Profibus card
Terminals block

This PLC is used to control the linear winch functions (in automatic
and manual operations).

There is also a Profibus port available for connection with the HPU PLC.
It may be used for interfacing the HPU commands (on-off) and to monitor
the HPU faults and alarms.

Control panels :
It will include the following :
316L stainless steel panel, 3 mm (385 mm (H) × 540 mm (W)
Synoptic panel
Control buttons & lamps
Linear winch
Speed potentiometer
Line-pull potentiometer
Button manual / 0 / automatic
Push-buttons for manual speed control
Wedges opening controls
Pull / pay-out selector
Start / stop
Stop buzzer / fault reset
Lamp test
Emergency stop
Pilot lamps :
5" 1/2 Exe screen for cable tension, speed & length displays,
status and faults & alarms displays, and calibration set & preset inputs.
Connection block

Party verification :
This order includes a 3rd party FAT witness certificate from DNV.
It includes :
Witness of pressure tests (hydraulic cylinders, piping)
Witness of FAT
Lifting pad-eyes certificate DNV 2.7.3 for offshore handling.
Drop tests and lifting on 2 points are not provided.
Manufacturing documentation review
FAT witness

Protection :
This equipment is designed to be operated on open deck.

Painting : A 3 coating marine paint, 320 µ is included. It will be according to Norsok
M501 RAL 1007 system 1.
Concerning the piping on the winch, it is CS made, and the manifold blocks
have BSP ports for fitting quick release couplings.

Quality control :
Quality control is carried out according to ISO 9001-2008.
An ITP is issued during the first month after contract, and progress plan and
reports are regularly controlled.

Documentation :
All the necessary documentation ( according to Norsok Z-015)
related to the design, fabrication, testing, inspection and maintenance of the riser
pulling equipment will be provided

This will include :
Design drawlings and as-built GA drawings
Material certificates and test reports
Equipment and instrumentation data sheets
Traceability records of raw materials such as steel plate, fasteners, pins
and shafting from Kley France sub-vendors.
Welding procedures (WPS's), Procedure qualification reports
(PQR's), and welder qualifications
NDE procedures, records, and qualifications of NDE personnel
Non-conformance/discrepancy reports and final dispositions
Dimensional control reports
Weight and centre of gravity data sheets and certificates
Kley France certificate of compliance
DNV certificates
Installation and preservation procedures
Operasjon and maintenance manuals
Lists of available spare parts

Sale/charter rate & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

The details mentioned above are believed to be accurate but are not guaranteed.

----------------------------------------------------------------------------------------------------
Search words :
Linear Winch for Sale
Linear Winch KTC 240 for Sale or Charter
KTC240 Linear Winch for Charter
Winch for Sale - KTC 240
Linear Winch KTC 240 for Sale
Linear Winch for Charter
Winch for Sale or Charter

---------------------------------------------------------------------------------------------------

     
Worldoils Oil, Gas and Offshore Marketplace
Worldoils Oil, Gas and Offshore Marketplace - Linear Winch KTC 240 for Sale or Charter
Images
 
Linear Winch for Sale
 
Linear Winch KTC 240 for Sale or Charter
 
KTC240 Linear Winch for Charter
 
Winch for Sale - KTC 240
 
Linear Winch KTC 240 for Sale
 

To enquire on this equipment, please send an email to

The information contained herein is believed to be accurate but has not been verified. This equipment is subject to prior sale and sold “where-is as-is” with no warranties from Worldoils Pte Ltd or the Seller expressed or implied.
Worldoils Oil, Gas and Offshore Marketplace    
Worldoils Oil, Gas and Offshore Marketplace

 


 

If you cannot find the new or used offshore rigs, vessels or equipment of any type, size or make that you are looking for, please send us an email to and we shall offer you.

Linear Winch KTC 240 for Sale or Charter
Worldoils Oil, Gas and Offshore Marketplace    Worldoils Oil, Gas and Offshore Marketplace

Equipment ID   : 1051
Equipment name   : Linear Winch KTC 240 for Sale or Charter
Category   : Winches
Specifications   :

Linear Winch KTC 240 for Sale or Charter
Winch for Sale - KTC 240


Scope of supply :
Equipment :
  1 Continuous linear winch KTC-240, 240 tonnes @ 1.3 m/min
  2 Hydraulic control modules, itegrated on the KTC-240
  1 PLC control cabinet for the winch command
  1 Control console
Factory testing of the unit
Commissioning and start-up spare parts
Painting and Protective coatings
Tagging
Documentation
DNV witness certificate
Weighing
Preservation, Packing & Marking
Delivery FCA Paris workshop
Operator training
Commissioning and start-up assistance

General characteristics :
Pulling capacity :
240T @ 0 to 1.3 m/min
115T @ 0 to 2.4 m/min
Operating temperature :
-15°C <T< +50°C (linear winch)
+5°C <T< +40°C (control cabinet and console)
Storage temperature :
-20°C <T< +60°C (linear winch)
-20°C <T< +60°C (control cabinet and console)
Environment : marine, on open deck
Hazardous area : zone 1 IIB T4

KTC-240 Linear winch :
The blocks are guided along 2 parallel U rails with stainless steel
removable supports and self lubricated interchangeable bearings.
For weight reasons, the frame is built in 2 seperate bolted parts,
and the gripped are removable from the frame.
The linear winch is attached working hanging or rested, horizontally
on deck foundations (yard supply).
Continuous motion.
Strong construction frame.

Characteristics :
Pull-in capacity (SWL) : 240 metric tones (to be tested during fat)
Speed at up to 240T : 1.3 m/min continuous and adjustable
Speed at up to 130T : 2.4 m/min continuous and adjustable
Oil consumption at maximum speed : 2 × 120 l/min
Pressure at SWL : 290 barg
Back tension at SWL : not required
Jack stroke : 950 mm
Wire rope diameter : 72 mm (with changeable inserts)
Maximum cable dia : 89 m (3" 1/2)
Overall dim : 2.24 m (W) × 8.10 m (L) × 0.80 m (H)
Weight : 23.5 tonnes = 2 ×(6.95 t + 4.8 t)
Design life : 25 years operation

The winch shall be capable of hauling-in and paying-out under any load,
in automatic and manual mode, in continuous operation.
It also includes 4 guide rollers (2 horizontal and 2 vertical ones) for the
back side (low tension side).

Hydraulic control modules :
The linear winch frame includes 2 hydraulic modules (one for each gripper)
for the synchronization, control and safety of the grippers of the linear winch.
They are mounted and piped on the frame itself. They are suitable to operate
into a hazardous area (Atex zone 1).

They are equipped with an integrated line-pull limitation. A potentiometer
adjusts the line-pull between 0 and 100%, and a software preset adjusts
the 100% betweem 50 t and 240 t.

For the powering of the linear winch, an external and independent
2 × 75 kW. HPU in LS control and with 2 × 130 l/min @ 310 barg. The HPU
has 4 outlets on each pump : pressure, return, drain and LS. The linear
winch must be fitted to this system for male connections (hydraulic inlet
power to the linear winch).

Required oil power for the linear winch should be as follows :
two identical and independent supplies (1 for each gripper) of  3 lines
each, with each the following utilities requirements :
P with 130 l/min at 310 bar per gripper
R with 160 l/min at ≤ 5 bar per gripper
D with 15 l/min at ≤ 1 bar per gripper
LS connections

Fittings internal on the linear winch :
On the main connections/ tubing it's require with SAE flanges.
On the smaller connections/ tubing where SAE flange won't
be used (10 and 12 mm tubes) it's required with parker EO2
fittings.
The hydraulic connections shall be assembling on one place
(scot plate) for each gripper.
Connections shall be as follow :
Pressure : 5/4" bsp male
Return : 1.1/2" bsp male
Drail : 3/4" bsp male
LS : 1/4" bsp male

Local control cabinet & panel :
The winch is supplied with the PLC control and command,
necessary for its full control and located remotely to the
winch. It is suitable for hazardous area (Zone 1)

a) PLC Cabinet :
The PLC cabinet is supplied loose, to be mounted into a
weather protected control container

It will include :
EExd cabinet
Power supply 230 v - 50/60 hz delivered with electrical supply cable
H07RN-F rubber cable 2,5G3 (2,5 mm2 with 2 conductors + earth)
PLC, Siemens S7
I/O cards
Profibus card
Terminals block

This PLC is used to control the linear winch functions (in automatic
and manual operations).

There is also a Profibus port available for connection with the HPU PLC.
It may be used for interfacing the HPU commands (on-off) and to monitor
the HPU faults and alarms.

Control panels :
It will include the following :
316L stainless steel panel, 3 mm (385 mm (H) × 540 mm (W)
Synoptic panel
Control buttons & lamps
Linear winch
Speed potentiometer
Line-pull potentiometer
Button manual / 0 / automatic
Push-buttons for manual speed control
Wedges opening controls
Pull / pay-out selector
Start / stop
Stop buzzer / fault reset
Lamp test
Emergency stop
Pilot lamps :
5" 1/2 Exe screen for cable tension, speed & length displays,
status and faults & alarms displays, and calibration set & preset inputs.
Connection block

Party verification :
This order includes a 3rd party FAT witness certificate from DNV.
It includes :
Witness of pressure tests (hydraulic cylinders, piping)
Witness of FAT
Lifting pad-eyes certificate DNV 2.7.3 for offshore handling.
Drop tests and lifting on 2 points are not provided.
Manufacturing documentation review
FAT witness

Protection :
This equipment is designed to be operated on open deck.

Painting : A 3 coating marine paint, 320 µ is included. It will be according to Norsok
M501 RAL 1007 system 1.
Concerning the piping on the winch, it is CS made, and the manifold blocks
have BSP ports for fitting quick release couplings.

Quality control :
Quality control is carried out according to ISO 9001-2008.
An ITP is issued during the first month after contract, and progress plan and
reports are regularly controlled.

Documentation :
All the necessary documentation ( according to Norsok Z-015)
related to the design, fabrication, testing, inspection and maintenance of the riser
pulling equipment will be provided

This will include :
Design drawlings and as-built GA drawings
Material certificates and test reports
Equipment and instrumentation data sheets
Traceability records of raw materials such as steel plate, fasteners, pins
and shafting from Kley France sub-vendors.
Welding procedures (WPS's), Procedure qualification reports
(PQR's), and welder qualifications
NDE procedures, records, and qualifications of NDE personnel
Non-conformance/discrepancy reports and final dispositions
Dimensional control reports
Weight and centre of gravity data sheets and certificates
Kley France certificate of compliance
DNV certificates
Installation and preservation procedures
Operasjon and maintenance manuals
Lists of available spare parts

Sale/charter rate & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

The details mentioned above are believed to be accurate but are not guaranteed.

----------------------------------------------------------------------------------------------------
Search words :
Linear Winch for Sale
Linear Winch KTC 240 for Sale or Charter
KTC240 Linear Winch for Charter
Winch for Sale - KTC 240
Linear Winch KTC 240 for Sale
Linear Winch for Charter
Winch for Sale or Charter

---------------------------------------------------------------------------------------------------

     
Worldoils Oil, Gas and Offshore Marketplace
Worldoils Oil, Gas and Offshore Marketplace - Linear Winch KTC 240 for Sale or Charter
Images
 
Linear Winch for Sale
 
Linear Winch KTC 240 for Sale or Charter
 
KTC240 Linear Winch for Charter
 
Winch for Sale - KTC 240
 
Linear Winch KTC 240 for Sale
 

To enquire on this equipment, please send an email to

The information contained herein is believed to be accurate but has not been verified. This equipment is subject to prior sale and sold “where-is as-is” with no warranties from Worldoils Pte Ltd or the Seller expressed or implied.
Worldoils Oil, Gas and Offshore Marketplace    Worldoils Oil, Gas and Offshore Marketplace

 

Worldoils Land Rigs Market
1000hp Land Drilling Rigs
1500hp Rotary Land Drilling Rigs
2000hp Rotary Land Drilling Rigs
3000hp Rotary Land Drilling Rigs
Workover Land Rigs
Carrier Mounted Land Drilling Rigs
Trailer Mounted Land Drilling Rigs

Oilfield Container Camps

Oil Booster Pump for Wellhead Platforms

Offshore Jackup Rigs
Land Drilling Rigs
Barge  Swamp Rigs

Live Monitoring of Ships and rigs

Remote ship Bunker GFuel Monitoring

Ring Maintenance Software

New Offshore Jackup Rigs

Oil Rig Jobs

Helicopters for Sale, Helicopters for Oil Rig Services


 

If you cannot find the new or used offshore rigs, vessels or equipment of any type, size or make that you are looking for, please send us an email to and we shall offer you.


.......................................................................
www.worldoils.com  |  Disclaimer  |  Ethics