Trailer Mounted New Drilling Rig 1000hp for Sale
Worldoils Oil, Gas and Offshore Marketplace    Worldoils Oil, Gas and Offshore Marketplace

Equipment ID   : 1436
Equipment name   : Trailer Mounted New Drilling Rig 1000hp for Sale
Category   : Land Rigs
Specifications   : Trailer Mounted Drilling Rig for Sale
1000 hp Trailer Mounted Drilling Rig
New Built Mechanical Drilling Rigs for Sale

Description

I. Hoisting Equipment

i. Mobile drilling trailer mounted type 1000HP, with single drum drawworks, two
Detroit series 60 14.0 liter engines with two Allison S6610H transmissions with
hydraulic torque converter. Mast height 118 ft., load capacity-425,000 lbs. (210 ton API).
Rig mounted on a 4-axle chassis.

A. Group I. Basic Rig

a. Drawworks – OEM-1000
i. Disc Brake System – Two (2) 60” O.D. x 4” Thick water cooled disc: Four (4)
brake calipers w/park feature, each caliper can develop 48,000 ft-lbs @ 100 psi.
Maximum 900 rpm calipers have a park feature rated @ 28,000 ft-lbs each. Manufacturer = Kobelt
ii. Air Clutch – Two (2) 30” diameter friction disc, slip torque rating 54,500 ft-lbs @ 100 psi,
maximum 760 rpm, 1664 sq in lining area. Manufacturer = Witchita.
iii. Drum 24” O.D. x 40” length with Lebus groove system
iv. Centralized Lubrication System
v. Drill line Diameter-1 1/8”
vi. Drive Chain - Four-strand, 1 ½” pitch
vii. Total Disc Brake Area - 1680 sq. inches

b. Auxilary Brake
i. Air Operated: Water Cooled Disc with copper alloy wear plates, mounted to frame,
coupled directly to drum shaft. Two (2) 36” Disc rated @75,000 ft-lbs @100 psi
maximum 640 rpm.
ii. Size-236 or equal
iii. Maximum Pressure - 100 psi
iv. RPM-640
v. Direct Coupled Drum shaft.
c. Combined Gear Box
i. Combined right angle drawworks drive drop box with one output shaft for rotary drive
and one output shaft (unused) for additional components.
1. One input shaft with 1810 drive flange.
2. Top right shaft - drawworks drive, air engaged 1.0 to 1 ratio keyed shaft
3. Top lower shaft - rotary drive, air engaged 1.1489 to 1 reduction ratio keyed shaft.
4. Bottom lower shaft – Future or additional components, opposite top lower shaft,
air engaged, 0.9787 to 1 ratio (1.0217 to 1 ratio increasing), 1810 drive flange.
ii. Gear type lubrication pump mounted intermediate shaft provides positive lubrication
to bearings.
d. OEM 118’-0” x 425,000# Telescoping Mast - The 118ft., mast provides is a telescoping
design, manufactured in accordance with API and Drilling Structures Int’l Inc.’s strict
quality control processes.
The mast includes an automatically deployed racking board.
i. A telescoping derrick with open face derrick design, manufactured to API 4-F
specifications. The open face design utilizes structural steel construction, which allows
for maximum block clearance. Derrick includes a ladder from rig floor to crown and a
block cradle with chain & hook for securing block during transport.
ii. Specifications
Mast Height : 118’
No. of Lines to Block - 8 or 10
API Operating Hook Load
- 8-Lines 340,000 lbs.
- 10-Lines 425,000 lbs.
Drilling Line Size : 1-1/8 in.
Racking Board Height - 55 ft., 58 ft., 70 ft.
Racking Board Capacity 5 in. Drill Pipe - 12,400 ft.
iii. Base Section
a. A-leg style base section hinged to carrier frame. (2) Turnbuckles attached from
bottom of derrick base to carrier frame allow for mast angle adjustment.The well-side derrick
legs have manual screw jacks.
iv. Lower Section
a. 6 in x 6 in x 3/4 in angle main legs, with 6 in x 4 in x 3/8 in rectangular tubing
“back” braces. Lower section of mast hinges to top of derrick base and rests on headache
rack during transport.
v. Upper Section
a. Angle construction. 6 in x 6 in x ¾” upper legs, with 3 in x 3 in x 3/8 in “back” braces. Upper
section rests inside lower section until mast is raised. Upper section then telescopes
hydraulically upward from lower section and locks in place with automatic latching pins.

vi. Crown Block
a. Crown block is set up for a 8 or 10 line string-up. Crown sheaves are grooved for 1-1/8 in.
Wire line. All sheaves are mounted on tapered roller bearings with grease certs for ease
of maintenance.
b. Crown includes: (1) one 30 in fast line sheave, and (4) four 24 in crossover sheaves.
vii. Racking Board
a. The mast includes an all welded racking board. The racking board automatically deploys
as the mast is extended.

viii. Derrick Raising System
a. The derrick is designed to utilize two, 72”x 9” x 3-stage, double acting raising rams and
one 50’ x 7” single-stage telescoping cylinder.
ix. Guylines
a. Derrick includes (2) load guys from the crown to carrier and (1) set of wind guys that meet or
exceed API specifications.
e. Hydraulic Catworks
a. Hydraulic break out cylinder for breaking out pipe connections, 4 ft. stroke,
maximum pull load 20,000 lbs. Installed on the mast. Includes cable, roller guides and
hydraulic piping.
b.Hydraulic make up cylinder for making up pipe connections, 4 ft. stroke, maximum pull
load 20,000 lbs. Installed on the mast. Includes cable, roller guides and hydraulic piping.
c. Controls are located at the operator’s console
f. Traveling Block Limit Switch (Crown Block Saver)
a. Safety device for limiting traveling block raising. Installed at the main drum to activate the
main brake when traveling block is up to a pre-determined height.

g. Deadline Anchor
a. Dead line anchor to be used with compression type weight sensor. Drum type, mounted on
carrier frame in front of drawworks frame.
h. Diesel Engine
a. Two Detroit series 60 - 14.0L engines rated at 600 BHP each@ 2100 RPM’s, 6 cylinders
(inline) complete with DDC electronic control system.
b. Includes: Radiator, Heavy Duty Blower, 24V starter and alternator, variable speed governor,
full instrumentation (ignition switch, ddr connector, electic throttle, electronic display module),
two (2) 12v batteries and spark arrestor muffler.
c. Specifications: 600 BHP @ 2100 RPM, 1650 lbs/ft @ 1100 RPM
i. Transmission
a. 5 speed (6th gear locked out), automatic, Allison S6610H or equal w/torque converter,
oil cooler. Dual air/hydraulic operation. Max. capacity 850 HP, 2500 RPM, 2300 ft-lbs input.
j. Compound Gear Box
a. Compound gear box, dual input, single output, may be drive with one or both engines.
b. Two input shafts, air engaged, 1810 drive flange (engagement of either input or a
combination of both)
c. Single output, 1810 drive flange, ration 1.0271 to 1 to combination gear box.
d. Gear type lubrication pump. Mounted to output shaft provides positive lubrication to bearing.
k. Power Take-off
a. Chelsea 852 XB or equal, Used for hydraulic pump drive, mounted on transmission,
95 HP @ 1000 rpm output.
l. Hydraulic System
a. Two hydraulic gear pumps, one 500 gallon hydraulic tanks with containment pan, filters,
heat exchanger and sight glass. Capable of producing 50 gpm @ 3000 psi, pressure return and
circulation filters with visual indicator, 3000 watts portable generator, inline flow meter,
system safety release valve, circuit breaker panel for heater/valve bank, operator panel
with selector switch.
b. Custom built valve bank, 15 station manifold, prewired control panel and hand held remote
with the following functions:
i. Mast lower/raise
ii. Mast telescope up/down
iii. Two (2) hydraulic pilot operated directional valve and joystick for winches.
iv. Six (6) leveling jacks.
v. D.S. sub raise/lower
vi. ODS sub raise/lower
vii. Make up/Brake out tong cylinders with remote torque adjustment
viii. Flow dividers for mast raise and sub cylinders
ix. Electrical control panel, remote controls and function switches for above
x. Velocity fuses on all cylinders for fall protection.
m. Air System
a. Air system with on (1) 60 gallon receiver to provide air to main air line and brake system.
Includes air lines, control valves, pressure gauges.
n. Air Compressor
a. Air compressors with direct drive, mounted on engine.
b. Reciprocal type, 28 CFM capacity
o. Operator’s Controls
a. Operator’s console to include the following controls and instrumentation:
i. Main drum brake lever
ii. Main drum clutch controls
iii. Two engine throttles – One (1) hand and one (1) foot
iv. Shift levers for two 4-speed transmissions
v. Two emergency engine shut downs
vi. Hydraulic pump controls
vii. Two mud pump engine regulators
viii. Mud pump engine emergency shut down
ix. Mud pump clutch controls
x. Instrumentation Air Pressure Gauge
b. All air operated controls are located in the central part of the console and have identifying tags.
Console is located to provide good visibility of traveling block, work floor and racking board.
p. Engine Emergency Shut Down
a. One engine emergency shut down valve for emergency engine stop. Located at the
operator’s console.
q. Trailer Mounted
a. A heavy duty 4-axle trailer with air suspension and 109,000 lb. total capacity.
b. All lights and brakes are equipped for attachment to the truck
c. Spring brake chambers for safety.
r. Tires (12.00 x 22.5, Pirelli Radial) 16 each
a. All tires, disc wheels, 16 tires mounted as dual. Tire rating 109,000 lbs. total, all tires inflated to 100 psi.
s. Suspensions
a. One (1) two axle, single point bogey at rear.
b. Two single axles with air bags, air can be dumped for backing into position
c. All axles are 12.5 metric ton capacity.
t. Four Pedestals for Hydraulic Jacks
a. Pedestals under front jack for rig stability. Four pedestals require. There are to be six jacks for
leveling the rig.
u. Six Hydraulic Jacks
a. Six hydraulic leveling jacks to take off the load from the axle and provide horizontal position of the
rig during operation. Each jack is operated by its own controls and is equipped with screw with
thrust nut,which allows relieving hydraulic pressure from he jacks during rig operation. Controls are
located at the mast supports.
v. Fuel Tank
a. Mounted on the side of the chassis
w. Auxiliary Hydraulic Winch (2 winches using one for spare)
a. Braden or equal hydraulic winch with 12,000 lbs. pull load at the first layer, 336 fpm @ 65 GPM
and 2400 psi.
b. Hydraulic brake and spooler
c. Sheave is mounted on the crown

x. Rotary Table Drive
a. One rotary table drive with driveshaft and two air clutches(one for rotary on and off, second for emergency
shut down)
b. Controls are located at the operator’s console
y. Rotary Table Drive Chain Gear Box
a. Includes three oil-greased shafts inside full-length guard, complete with sprockets, flanges, chains and
chain gear-box with one shaft to connect to rotary table. One lower section mounted on the trailer, one upper
section mounted on the sub and one flanged driveline between.
z. Drill Line
a. 1 1/8” OD drill line, 6 x19s IWRC, 3000 feet
Group II - Substructure and Assessories
A. OEM Hydraulically Telescoping 17-425 Substructure
1) Material and labor to fabricate one (1) OEM hydraulic telescoping 17-425 substructure 
as per the following:
i. Hydraulic Telescoping Substructure with:
- 425,000# Rotary beams
- 300,000# Setback.
- Clear height under rotary beams = 14’
- Transportation height 12’-6”
- Base dimensions 45’L x 12’-6”W
- Working floor dimensions 20’ x 26’
- Rathole and mouse hole locations
- Two tong backup posts
- Removable braces in cellar area.
- Provisions for attaching mast support beam.
- Supply and installation of four (4) hydraulic scoping cylinders.
- Pull out post for guy wires to front of mast.
- Removable flooring around rotary table area.
- B.O.P. Dolly and tracking.
The above substructure to be fabricated under A.P.I. 4F guidelines. Upon completion, 
substructure to be tagged with OEM A.P.I. 4F
B. Mud Boat
i. Material and labor to fabricate one (1) mud boat. Mud boat complete with:
1. Supports under jacks on carrier.
2. Pipe guides for tires
3. Pin connections to mast support beam.
4. Loading hitches on one end
C. Mast Support Beam/Brake Water Tank/Trip Tank Combo
i. Material and labor to fabricate one (1) mast support beam/trip tank/brake water 
tank combination. Combination complete with:
1. Brake Water Tank - Material and labor to fabricate one (1) break water tank. Tank to be
enclosed for rig up winterization.
a. Tank to have the following:
i. Tank bottoms to be 3/8” plate.
ii. Tanks constructed with ¼” v-crimp.
iii. Tank rims to be 4” square tubing.
iv. Access ladder
v. Man way
vi. Tong buckets, guides, and safety cage.
vii. Supply and installation of:
1. Two (2) 2 x 3 centrifugal pumps
2. Heat exchanger
2. Trip Tank – Material and labor to fabricate one (1) trip tank. Tank to be enclosed for
rig up winterization.
a. Tank to have the following:
i. Tank bottoms to be 3/8” plate.
ii. Tanks constructed with ¼” v-crimp.
iii. Tank rims to be 4” square tubing.
iv. Access ladder
v. Man way
vi. Tong buckets, guides, and safety cage.
vii. Provisions to mount:
1. One (1) 2 x 3 centrifugal pumps
3. Mast Support Beam – Material and labor to fabricate one (1) three runner mast support beam.
a. Support beam complete with:
i. Supports for carrier jacks and bottom base of mast.
ii. Loading hitches on both ends for tailboarding.
D. Rig Floor Stairways– All stairs to meet OSHA standards with no slip grip strut stair treads.
i. Three (3) 17’-0” stairway from substructure floor to ground level. Stairs to be built on
a 45-degree angle.
ii. One (1) 9’-6” stairway from top of the substructure to top of mud tank. Stairs to be built on
a 45 degree angle.
E. V-Door Ramp- Ramp to be fabricated to work with a 17-0” floor height substructure and
an 18” catwalk. Ramp to be fabricated with ½” plate and 3” pipe guides.
F. Catwalk– One 50’ x 5’-0” x 18” catwalk with snatch post mounted on one end.
G. Doghouse- House to be fabricated on a three-runner oilfield type skid with loading hitches on
both ends for tailboarding. House to have checker plated flooring, v-crimped wall
construction, and an arched type roof. House complete with the following:
1. 4’-0” porch on one ends
2. 2’-0” walkway on the back side of the doghouse running to full length.
3. Handrails around house perimeter.
4. One sliding doorway to rig side.
5. One swing type doorways on both ends with windows built in.
6. Two (2) windows on the back side wall
7. Knowledge box
8. Three compartment workbench.
Group III - Prime Mover Drive
A. Lighting System–Heavy Duty explosion proof Fluorescent and Mercury Vapor
Lightning System designed to use with Mast and Substructure, Mud System, complete
with Plug, Receptacles, Cable, Cable Clamps and all necessary Leads and fitting. Lighting
System consist of: Mast and Racking Platform, Substructure Lighting, Mud Tanks and
Mud Pumps, and Utility House, including Battery emergency light at Driller’s console
certified for Class 1 Division 2.
B. Engine/Generator/Part/Change Package
a. Utility House - “New” - Material and labor to fabricate one (1) utility house. House (43’x 12’ x 9’)
to be constructed on an oilfield type skid (45’x 12’x 18”) with loading hitches on both
ends for tailboarding. Top of skid covered with ¼” checker plate.
i. Parts/change house to be complete with:
1. Twenty (20) lockers.
2. Changing bench near lockers.
3. Two sets of shelves on each wall running 8’-0”.
4. One (1) bench on each wall. Bench compartments to be 5’-0” with folding bench.
Two compartments to have ventilation to the outside for paint storage.
ii. Generator house complete with:
1 One (1) 8’-0” sliding door on side of the generator location
2. Provisions for mounting one (1) electrical plug panel.
3. Radiator end of skid left open.
4. Skid designed for generator tie downs to be mounted on cross beams of skid for safety.
b. Generator – Two (2) Detroit 60 Series 14L.
c. Electrical Specifications
i. Item 1 – Clarification
1. Prime mover specifications were not provided; IEC Systems assumes the engine
and generator sizes as listed in this proposal.
2. The generator house will be designed to accommodate the “Three Tank Drilling
Rig Standard” and thus be interchangeable with all rigs that meet the standard
3. IEC System proposal is based on performing the installation in Houston, Texas.
All components listed below will be installed and tested
4. Customer will furnish the voltage regulator and voltage rheostat
ii. Item 2 – Generator Houston Electrical System For a Mechanical Rig
1. Generator House 480 VAC Switchboard
a. 1 ea - A/C Generator Control Panel by IEC Systems for the control of two (2),
450 kW, 480 volt, 3 phase, 4-wire, 60 Hertz, A/C generators.
b. Switchgear to contain full instrumentation and will not be designed for full
parallel operation of generators.
c. Switchboard will be NEMA Type 1 enclosure with ASA #61 gray enamel finish,
designed to meet NEMA and OSHA specifications.
d. All nameplates will be constructed of plastic plates, black on white for names
and red on white for warnings.

Generator controls mounted in the switchgear will consist of:
2 - Generator Main Circuit Breakers (Gen PWR)
2 - Generator "Power Available" Indicating Lights
2 - Voltmeters
2 - Voltmeter Switches
2 - Ammeters
2 - Ammeter Switches
2 - Frequency Meters
2 - Reverse Power Relays
1 - Ground Detection System
2 - Governor Control Switches
2 - Wire to Customer Furnished Voltage Regulators
2 - Wire to Customer Furnished Voltage Rheostats
1 - Lot Current Transformers, Potential Transformers, Fuse Blocks, Fuses,
Buss Bar, Switchboard Wiring, and related equipment
Switchboard will be fully assembled, wired, and shop tested.
2. Generator House 480V Motor Control Center (MCC)
a. 1 ea - 480 Volt, 3-phase, 60 Hertz A/C Motor Control Center, equipped with braced horizontal
and vertical bus
b. Enclosure will be NEMA Type 1 with front only access
c. Motor starters will be combination, full voltage- non-reversing with 3-pole overload
blocks, heaters, control power transformer, operating handle, fuses and start/stop
controls in cover with red "RUN" indicating lights
d. 480V MCC Motor Starters
i. Five (5) Size 4 Starters for:
1 ea 60 HP Mud Mixer 1
1 ea 60 HP Mud Mixer 2
1 ea 60 HP Desander
1 ea 60 HP Desilter
1 ea Spare
ii. One (1) Size 3 Starter for:
1 ea 40 HP Trip Tank

iii.Five (5) Size 2 Starters for:
1 ea 20 HP Drill Water 1
1 ea 20 HP Drill Water 2
1 ea 25 HP Brake Cooling Pump 1
1 ea 25 HP Brake Cooling Pump 2
1 ea Spare
iv. 480 V MCC Motor Feeder Circuit Breaker
1. 1 ea - 150 AMP 3 Pole Circuit Breaker for Camp Feeder
3. Generator House 480V Distribution Panel Boards
a. 1 ea - 480V POWER DISTRIBUTION PANEL BOARD (P1)
i. 480V, 3-Phase, 3-Wire
ii. NEMA 1 Enclosure
iii. 600A MLO with Feed-Thru Lugs
iv. 36 CKT with branch Circuit Breakers for the following loads:
a. 1 ea - 100A/3-Phase CB for 75 KVA Lighting Transformer
b. 1 ea - 60A/3-Phase CB for BOP Accumulator (30 HP)
c. 1 ea - 60A/3-Phase CB for Spare
d. 1 ea - 30A/3-Phase CB for Agitators 1, 2 Feeder (10 HP each)
e. 1 ea - 30A/3-Phase CB for BOP House Heater (15 kW)
f. 1 ea - 30A/3-Phase CB for Change House Heater (15 kW)
g. 1 ea - 15A/3-Phase CB for Liner Washer 1 (3 HP)
h. 1 ea - 15A/3-Phase CB for Liner Washer 2 (3 HP)
i. 1 ea - 20A/3-Phase CB for Fuel Pumps 1 & 2 Feeder (3 HP each)
j. 1 ea - 20A/3-Phase CB for Shale Shaker 1 & 2 Feeder (5 HP each)
k. 1 ea - 30A/3-Phase CB for Spare
L. 1 ea - 30A/3-Phase CB for Wireline (15 HP)
b. 1 ea - 480V DISTRIBUTION PANEL BOARD (P2)
i. 480V, 3-Phase, 3-Wire
ii. NEMA 1 Enclosure
iii. 600A MLO with Feed-Thru Lugs
iv. 30 CKT with branch Circuit Breakers for the following loads:
1. 1 ea 100A/3-Phase CB for Hydraulic Power Unit (HPU), (50 HP)
2. 1 ea 100A/3-Phase CB for Air Compressors #1 & 2 (25 HP each)
3. 1 ea 20A/3-Phase CB for Vacuum Degasser (7.5 HP)
4. 1 ea 30A/3-Phase CB for Dog House Heater (15 kW)
5. 1 ea 60A/3-Phase CB for Agitators 3, 4, 5 Feeder (10 HP each)
6. 1 ea 30A/3-Phase CB for Hopper House Heater (15 kW)
7. 1 ea 40A/3-Phase CB for Spare
8. 1 ea 60A/3-Phase CB for Spare
9. 1 ea 30A/3-Phase CB for Spare
10. 1 ea 30A/3-Phase CB for Spare
4. Generator House 120/208 Distribution Panel Board
a. 1 ea - 120/208V DISTRIBUTION PANEL BOARD (P3)
i. 120/208V, 3-Phase, 4-Wire
ii. NEMA 1 Enclosure
iii. 225 MLO, Top Feed
iv. 42 CKT with branch (124/240V-10 KAIC) Circuit Breakers for the following loads:
1. 1 ea - 100A/3-Phase CB for Rig Floor Lighting Panel
2. 1 ea - 100A/3-Phase CB for Spare
3. 1 ea - 100A/3-Phase CB for Boiler House Feeder
4. 1 ea - 60A/3-Phase CB for Spare
5. 1 ea - 30A/3-Phase CB for Spare
6. 10 ea - 20A/1-Phase CBs for Lighting Circuits 1 thru 10
7. 1 ea - 20A/1-Phase CBs for Engine/Generator House Steam Heater Blowers
8. 1 ea - 20A/1-Phase CBs for Trip & Shaker Tank Steam Heater Blowers
9. 1 ea - 20A/1-Phase CBs for Mud Pump 1 & 2 Steam Heater Blowers
10. 1 ea - 20A/1-Phase CBs for Mixer Skid Steam Heater Blowers
11. 1 ea - 20A/1-Phase CBs for Engine/Generator House Lighting Circuit
12. 1 ea - 20A/1-Phase CBs for Generator 1 & 2 Block Heater Feeders
5. Generator House Plug Board
a. 1 ea Metal shroud protected weatherproof receptacle panel with matching plugs for all the
above starters and circuits having cables that exit the Generator House.
b. Receptacles to have protective vapor proof caps. Plugs and receptacles will be
permanently identified.
c. 480V Plug and Receptacle sets provided for the plug board include all loads listed above in
Section C and D (MCC and Panel Board Loads)
d. Additional Plug Board Spare Plugs and Receptacles
6 ea 30A, 3-Pole, 480V
5 ea 60A, 3-Pole, 480V
2 ea 100A, 3-Pole, 480V
6. Generator House 480/208-120V Rig Lighting Transformer
a. 1 ea 75 KVA Transformer with 480V Primary and 120/208V Secondary mounted in a
drip-proof enclosure.
Primary Power will be from the P1 Panel Board.
7. Generator House Power and Control Cabling
a. 1 lot A/C Power and Control Wiring by IEC Systems to connect two 450 KW, 480 volt,
60 Hertz A/C generators to 480V Switchboard
b. All A/C generator power cables with 90 0C rates insulation sized/de-rated for use in
45 0C ambient atmosphere.
c. 1 lot Glastic Plates to prevent excessive heat caused by electrical fields where power
cables enter generators.
d. 1 lot A/C Power and Control Wiring to connect A/C generator control panel to:
i. MCC
1. P1 Panel Board
2. P2 Panel Board
3. P3 Panel Board
4. 75 KVA Lighting Transformer
5. Generator House Plug Board (receptacles)
8. Generator House Lighting
a. Generator Sheds Lighting receptacle string complete with plugs and receptacles,
cable, cable clamps, and all necessary leads and fittings to accommodate the following:
i. 4 ea - C1D2 Hazardous Area fluorescent fixtures complete with lead
ii. 1 ea - C1D2 Hazardous Area Metal Halide floodlight fixture complete with lead
iii. 1 ea - Mounting Stanchions for Floodlights

Group IV - Rotating Equipment
B. “New” American Block Traveling Block and Hook
a. 250 Ton Traveling Block, API load rating: 250 Ton, sheave groove 1 1/8”.
C. “Rebuilt” National C275 Rotary Table and Accessories
a. 27 ½” rotary table with 27 ½” table opening, static load capacity: 650 ton, gear ratio
3.6:1, torque cap: 30,000 ft-lbs @ 60 rpm.
D. “Rebuilt’ Rotary Swivel
a. 250 Ton
Group V - Circulating Systems
A. Two “New” Mechanical Drive 1000HP Mud Pumps
a. Two (2) “New” Eweco - 1100HP Mud Pumps
b. Two (2) “New” Detroit D2000 Engines
c. Unitized on one common skid with:
i. Model C-300-100F(H) OWI Torque Converter
ii. Belt Drive
iii. Dual 24” Eaton Airflex
iv. Drum Hub for 24” Dual Clutch
v. Drum Flange, external 24”
vi. 5 x 6 Centrifugal pump
d. Control system including:
i. Air throttle
ii. Air valve to engage and disengage clutch
iii. Hoses and mounting hardware.
B. Two Tank 850 BBL Mud System- Material and labor to fabricate one (1) two
tank 850 bbl mud system as per our discussions. OEM to completely fabricate tanks
(40’ x 10’-6” x 7’-0”) on a three runner oil field type skid (50’ x 7’-10” x 8”) with loading
hitches on both ends for tail boarding. Tanks to have internal ladders to each compartment,
equipment supports, fold down type handrails and covered with galvanizes bar grating
Mud system to consists of the following:
i. Shaker Tank – Four equal compartments
-Shale Pit
• 10’-0’’ compartment
• One (1) cleanout
• One (1) overflow
- Desander Pit
• 10’-0 compartment
• One (1) cleanout
• One (1) overflow
• One (1) 6” suction line from 5 x 6 centrifugal pump.
• One (1) 8” equalizer. Bottom mounted with top mounted handle.
- Desilter Pit
• 10’-0’’ compartment
• One (1) cleanout
• One (1) overflow
• One (1) 6” suction line from 5 x 6 centrifugal pump.
• One (1) 18” equalizer. Bottom mounted with top mounted handle.
• Equipment supports for one (1) 10 HP agitator
- Degasser Pit
• 10’-0’’ compartment
• One (1) cleanout
• One (1) overflow
• One (1) 8” bottom equalizer and one (1) 8” top equalizer.
• Equipment supports for one (1) 10 HP agitator.
- 9’-0’’ Porch
• Able to accept two (2) 5 x 6 centrifugal pumps
• 10’’ equalizer line to Suction Tank.
• Covered with ¼’’ Chk’d floor plate.
• Overhead plated roof.
ii. Suction Tank – Two Compartments.
- Suction compartment
• 30’ – 0’’ compartment
• One (1) cleanout gate.
• Two (2) 6” suction lines going to main mud pumps.
• Equipment supports for two (2) 15 HP agitators.
- Pill Compartment
• 10’-0’’ compartment.
• One (1) cleanout gate.
• One (1) 8” equalizer. Bottom mounted with top mounted handle.
• One (1) overflow
• Equipment supports for one (1) 10 HP agitator
- Porch
• Able to accept two (2) 5x6 centrifugal pumps.
• 6’’ line to both pumps
• One (1) discharge dumping line
Pill Tank
Suction Tank.
iii. Accessories
1. Single slide for shaker. Slide to mount to the side of the tank and fold down
during transportation. Slide complete with 6” pipe end for hose hook up in the field.
2. Single slide for desander. Slide to mount to the side of the tank and fold down
during transportation. Slide complete with 6” pipe end for hose hook up in the field.
3. Single slide for desilter. Slide to mount to the side of the tank and fold down
during transportation. Slide complete with 6” pipe end for hose hook up in the field.
4. Fold down type walkways around shaker area complete with galvanized grating and
handrails. Walkways to fold down during transport.
iv. Solid Control Equipment
1. Four (4) Mission Magnum 6 x 5 x 11 magnum1 with a 10.5 inch impeller, mechanical
seal and hard iron material, all mounted on a mission fabricated steel base with woods
style coupling, OSHA type coupling guard and a 75 HP 1750 RPM, 3 PH, 230/460 Volt,
60 Hz explosion proof electric motor.
2. Three (3) Derrick DE-AG-10 Agitators complete with 10 HP, 1800 RPM explosion
proof C-face motor bolted to a gear box. Including shaft stabilizer, shaft and impeller.
3. Two (2) Derrick DE-AG-15 Agitators complete with 15 HP, 1800 RPM explosion
proof C-face motor bolted to a gear box. Including shaft stabilizer, shaft and impeller.
4. One (1) Derrick two cone desander.
5. One (1) Derrick sixteen cone desilter.
6. One (1) Hopper with venturi.
7. One (1) Derrick Vacuum degasser 1200 GPM. Skid mounted with heavy duty 3 HP
explosion proof 230/460 volt, 60 Hz, 3 Ph, 1800 RPM motor and manual starter with
heavy duty vacuum pump.
8. Two (2) Derrick Flo-Line Cleaner 503 Shale Shakers w/weir feed complete with
three panel screen frame, support structure, and explosion proof electrics with
the following options:
1. A.W.D. (+7 deg uphill to –1 deg downhill)
2 Standard Screen Underflow hopper
3. Weir feed
4. Super G Vibrations Motors
5. Single side tensioning system
9. 36” Poor Boy Degasser on a separate skid.
VI. BOP
A. Six (6) Station Accumilator
B. Choke & Kill Manifold
C. Note – BOP to be supplied by others (Not include in pricing.)
VII - Utilities
A. Air Compressor & Receiver
a. Two (2) Gardner Denver, ST-30, Electra-Saver II, rotary screw air compressor,
Model EBE99Q. 30 HP, 460 volts, 3 phase, 60 HZ, TEFC, with NEMA 4 Control Enclosure.
b. Two (2) Steel Fab, 400 gallon, vertical air receivers with full skirt, 200 psi working pressure.
Part # A12614. Unit is California Coded.
c. One (1) RNC250 air dryer for 250 CFM.

VIII. Instrumentation
A. Drift Indicator
Totco Double Recording Drift 0 to 8 and 0 to 14. Clock complete with following:
- 1 ea. Godevil Kit
- 1 ea. Chart tool & Chart Reader
- 1 ea. Tool Maintenance Box w/ Tool
- 100 ea. Chart 0 to 8
° and 0 to 14°
- 10 ea. Rubber Finger Stabilizer
- Fishing Tool 7 rope sockets
B. Indicator/Gauge & Counter
EMS-2 or Equivalent Rotary Torque indicator, Weight indicator, and Tong torque gauge,
Circulating pressure gauge, two (2) ea. Pump stroke counter.
C. Drilling Recorder
EMS-2 or Equivalent Drilling recorder, 9 pen (weight, torque, penetration rate, pump
pressure, rotary rpm). (Diameter 103 Dan Kurang 6 Buah Printed Circuit Board).
D. PVT
EMS-2 or Equivalent Pit volume totalizer, single channel with audio alarm and
warning lights, four pit transmitters totalizing relay, gain and loss gauge with gauge
zero devices. Full digital instrumentations.
E. Flow-Shoe-Device
EMS-2 or Equivalent Device complete with recorder and alarm system
Group IX - Fabrications
A. Accumulator/Junk Bend/Air Package Combo
a. Material and labor to fabricate one (1) accumulator/pipe bend skid as per our conversations.
OEM to fabricate a three runner oilfield type skid (40’ x 10’ x 12”)
covered with ¼” check plate. Piping to be done during rig up. Skids complete with:
i. One (1) arched type roof and enclosure.
v. Mounting supports for two (2) vertical air receivers.
vi. Mounting supports for one (1) accumulator.
vii. Mounting supports for:
1. Two (2) air compressors
viii. Access doors
1. One 36” swing type door way
2. Two (2) 48” double door way.
B. Parts/Mechanic Shop - “New”
Material and labor to fabricate one (1) parts/change house. House (38’x 10’x 9’) to be
constructed on an oilfield type skid (40’x 10’x 12”) with loading hitches on both ends for
tailboarding. Top of skid covered with ¼” checker plate. House to be complete with:
- One (1) work bench and One (1) Table
- Two sets of shelves on each wall.
- Four (4) storage benches.
C. 500 bbl Water Tank
Material and labor to fabricate one (1) 500 bbl water tank as per our conversation. Tanks
fabricated on oilfield type skids with loading hitches on both ends for tailboarding. Skid ends
to be covered with ¼” check plate.
Tanks complete with the following:
- Two (2) 3 x 2 x 11 Centrifugal pumps with 25 HP Motors
- Suction and Discharge Piping.
- Two (2) ladder rung to top of tank (In and Out)
- 4” Fill cap
- 2” Outlet
- 1” Drain
D. One (1) 12,000 Gallon Fuel Tank
Material and labor to fabricate one (1) 12,000 gallon fuel tank as per our conversation.
Tanks fabricated on oilfield type skids with loading hitches on both ends for tailboarding.
Skid ends to be covered with ¼” check plate. Tanks complete with the following:
- Two (2) fuel transfer pumps
- One (1) filter system.
- Suction and Discharge Piping.
- Two (2) ladder rung to top of tank (In and Out)
Top and Side man ways, 4” Fill cap, 2” Outlet, and 1 ½” Drain
E. Cable Trays- Material and labor to fabricate one (1) lot of cable trays as per the following.
Cable trays to be fabricated as follows:
- Two (1) 40’-0” sections from substructure to fuel tank.
- One (1) 35’-0” section from mud tanks to main trays.
- One (1) 20’-0” section from substructure to main stairs.
- Cable trays complete with the following:
• Hinged doors in 5’-0” sections with chain for each doorway.
• Flat expanded metal running the length of each tray.
• ½” round bar at each end of cable tray to provide protection when pulling wires.
F. Mud Gas Seperator and Transportation Skid - “New”
- Material and labor to fabricate one (1) 36” poor boy degasser and skid. Gas buster to me
mounted on a three-runner oilfield type skid with loading hitches on both ends for tailboarding.
Gas buster complete with:
• 36” Pipe with weld caps on both ends.
• Internal baffles.
• All piping and pipe brackets.
• Gas buster to elevate to working condition to allow operation under half full conditions.
• Gas buster to be mounted in lay down position for transport and to be raised by
truck for operation.
Group X - Rig Up Items
A. High Pressure Piping
a. Material and labor to fabrication one (1) lot of high-pressure piping. All piping to be 4”
schedule 160 and all unions to be weld type 1002. High pressure piping complete
as per the following:
i. Standpipe
1. Standpipe to be located on the Off-Driller’s Side.
2. Standpipe to have hammer union breaks at mast sections so it can me transported
without being taken off the mast.
ii. Standpipe Manifold
1. The standpipe manifold will be complete with manifold type tee with two 2” outlets.
Outlets to have hammer union connections only.
2. The 4” outlets to have a 4” gate valve on the top of the cross.
iii. High Pressure Line
1. The high-pressure line will run from the bottom of the standpipe manifold to the
side of the mud boat
2. The cellar line will be mounted to the mast support beam.
3. There will be hammer unions at break of the substructures for transportation.
B. Structural set and assemble:
a. Mast and Substructure
i. Mast accessories.
ii. Install flooring, handrails, v-door, stairs, etc.
C. Set and align
a. Rotary Table
b. Drawworks
c. Doghouse
d. Utility house control panel and foot drawworks console.
e. Mud Pumps
f. Mud system
g. Brake water/trip tank
h. Water Tank/Fuel Tank
i. Catwalks and pipe racks
j. Cable Trays
k. Koomey/Junk basket
D. Piping, Fittings, hoses, valves, etc.
a. Water Supply
i. To Mud system and mixing system
ii. Rig Floor
iii. Brake water system
iv. Feed and return lines from brake water tank to drawworks drum and brake.
v. Fuel System
1. To feed and return lines from duel tank to generator set.
vi. Air System
1. Air Supply for accumulator unit and rig floor
2. Hose connections from rig floor air manifold to drawworks control console, air
hoist and other floor tools
a. To generator set engine starters
vii. Miscellaneous
1. Vibrator hoses.
viii. Electrical Rig Up
ix. Testing
1. Fill mud tanks with water
2. Provide lube products to all machinery.
3. Provide Fuel for testing
4. Circulate water through mud system
5. Run air compressors.
6. Pressure test all high pressure lines and connections to working pressure
7. Run all solids control equipment.
8. Load test generators
9. Test all SCR assignments.
x. Rig Down
1. Rig down and assist in load out on customer furnished trucks.

Price & terms : Please enquire using the email form below.


If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Mechanical Trailer Mounted Rig for Sale
1000hp New Land Drilling Rig in USA
Trailer Mounted Rig for Sale
Mechanical Drilling Rig 1000 hp for Sale
Trailer Mounted Land Drilling Rig for Sale

-----------------------------------------------------------------------------------------------------------

     
Worldoils Oil, Gas and Offshore Marketplace
Worldoils Oil, Gas and Offshore Marketplace - Trailer Mounted New Drilling Rig 1000hp for Sale
Images
 
Trailer Mounted Drilling Rig for Sale
 
Mechanical Trailer Mounted Rig
 
New Trailer Mounted Rig
 
1000 hp Mechanical Trailer Mounted Rig
 
Trailer Mounted Drilling Rig 1000 hp for Sale
      
    
    
    
  
Drilling Rig 1000HP for Sale - New
Land Rig - 1000 HP for sale
Schramm T64HB Drilling Rig - For Sale
Versa Drill V2000 Drilling Rig - For Sale
Gefco / Speedstar 30K-DH Drill Rig for Sale
Reichdrill T650W Drilling Rig - For Sale
Ingersoll-Rand DM25 SP Crawler Drilling Rig - For Sale
Chicago Pneumatic 650 S/S Drilling Rig for Sale
Drilling Rig - ZJ40 Truck Mounted For Sale - 1000hp
National 370 - Mechanical Drilling Rig - for Sale
Workover Rig - 550 hp - 2008 built for Sale
Drilling Rig - Cabot 900 Series Self Propelled - For Sale
Ideco H44 Drilling Rig for Sale
Simco 2800 HS (HT) Drilling Rig - For Sale
Drilling Rig - Gardner Denver SCR - 1000hp - for sale
Drilling Rig - OIME SCR 3000 HP - For Sale
Wilson Mogul 42 Double Trailer Mounted Rig for Sale
Drilling Rig - EMSCO GB 500 - 1200hp for sale
Drilling Rig - National 1320 SCR - 2000 hp for sale
Drilling Rig - Ingersoll-Rand DM-M2 - 2001 Built for Sale
Speedstar 1500 Drilling Rig - For Sale
Mechanical Drilling Rig - 750 HP - for Sale
Diesel Electric Rig - U-36 AE for Sale
Schramm Rotadrill T64HB Drilling Rig - For Sale
Workover Rig - LCI 750 - For Sale
Ingersoll-Rand T4BH (Blast Hole) Drilling Rig - For Sale
Drilling Rig - Deep Rock CTM 10,000 - 1986 Built for Sale
Mechanical Drilling Rig - Ideco U15 - 800 HP - for sale
Land rig - National T45 for sale
Speedstar 275 Quickdrill Rig for Sale
Drilling Rigs for sale or lease
Chicago Pneumatic T650 WS Drilling Rig - For Sale
SK 775D Carrier Mounted Drilling Rig for Sale
Drawworks - Brewster N-45 For Sale
Speedstar 70K Drilling Rig - For Sale
Drilling Rig - Atlas Copco T4W - 2005 Built for Sale
Chicago Pneumatic T-700WH Deep Hole Drill Rig & Package - For Sale
Schramm T660-H Drilling Rig - For Sale
Schramm T130XD Drilling Rig - For Sale
Schramm T64HB Drilling Rig - For Sale
Diedrich D120 Drilling Rig - For Sale
Drilling Rig for sale
Driltech D40K Drilling Rig - For Sale
Ingersoll-Rand RD20 Range II Drill Rig for Sale
Failing CF-15 Drill Rig For Sale
Atlas Copco T4BH Drilling Rig - For Sale
Ingersoll-Rand T3W Drilling Rig - For Sale
Drilling Rig - Ballerini ST4 - for Sale
Atlas Copco RD20 Range III Drilling Rig - For Sale
Workover Rig BW ALCO Double - 4200 m - for sale
Workover Rig- Cooper LTO 250 Double (3000m) - For Sale
Workover Rig - Four Axle Carrier Mounted - 375 HP - for sale
Ideco H30 Double Rig - 3000 m For sale
Ingersoll Rand TH60 Drilling Rig - For Sale
Taylor RT 5000M Trailer Mounted Drilling Rig - For Sale
Reichdrill Legend 4 Drilling Rig for Sale
Drilling Rig T4W For Sale
Service Rig - 600hp - for Sale
Speedstar SS-15 II Drill Rig for Sale
Mobile B61 Drill Rig - for Sale
Brewster N10 - 1000hp - Land Drilling rig For Sale
OIME SL7 HELI-RIG - 1000hp Helicopter Land Rig For Sale
Cabot 750 Mobile Carrier Rig - for sale
Taylor C550 Workover Used Rig - for sale
Electric Drilling Rig - New built - 1500HP for sale
Electric VFD Drilling Rig - New built - 2700 hp for sale
American Augers VR-500 Drilling Rig for Sale
Ingersoll-Rand T3W Drill Rig - 1988 built - For Sale
Land Rig Builders - for sale
Failing 1000 Drilling Rig - For Sale
Reichdrill T-650-W Drilling Rig - 1986 Built - for Sale
Driltech D25KW Drilling Rig for Sale
Atlas Copco T4BH (Blast Hole) Drilling Rig - For Sale
Driltech D40K Crawler Drill Rig for Sale
Schramm T660W Drilling Rig - For Sale
Ingersoll-Rand T4W Used Drill Rig Built 1978 for Sale
Ingersoll-Rand TH60 Drilling Rig - For Sale
Hydraulic Land Drilling Rig - New 2000HP for Sale
Speedstar 30K Drilling Rig for Sale
CME 45 Auger Drilling Rig - For Sale
Walker Neer C33-A Triple Drum Service Rig for Sale
Challenger M320 Drill Rig & Pipe for Sale
Land Drilling Rig for Hire
UMD 90 New Land Drilling Rig - for Sale
UMD 110 New Land Drilling Rig - For Sale
UMD 125 New Land Drilling Rig - For Sale
UMD 135 New Land Drilling Rig - For Sale
UMD 160 New Land Drilling Rig - For Sale in Europe
UMD 180 New Land Drilling Rig - For Sale
UMD 200 New Land Drilling Rig - For Sale
Speedstar 30K Drill Rig -1989 Built - for Sale
Williams LLDH Used Drilling Rig for Sale
Texoma TJ 254 Used Drilling Rig - For Sale
Texoma 500 Used Drilling Rig - For Sale
VFD Land Drilling Rig (Chinese) - 2000hp - for sale
SCR Land Drilling Rig (Chinese) - 2000hp - for sale
VFD Land Drilling Rig Chinese - 1500hp - for sale
National 1320 Used Land Rig - 2000hp - for sale
BW Rig Alco Double Used Workover Rig - 4200m For Sale
Ideco H35 KD Double (4200) - Used Workover Rig for sale
Ideco H30 Double - 3000m - Used - Workover Rig - For Sale
Cooper ITO 250 Double - 3000m - Used - Workover Rig - For Sale
Kin Rig S 300 Double - 3000m - Used - Workover Rig - For Sale
Kremco K 600 Double - 4200m - Used - Workover Rig - For Sale
Skytop RR 400 Double - 4200m - Used - Workover Rig - For Sale
SRE 600 Double - 4200m - Used - Workover Rig - For Sale
Driltech D35K Drilling Rig - For Sale
Schramm T64HB Drill Rig for Sale
Five Axle Carrier Mounted - New Workover Rig 475 HP - For Sale
Four Axle Carrier Mounted Land Workover Rig - 375hp - for sale
Single Drum Drawworks six axle Carrier - Mounted Rig 750 HP - for sale
CME 550 Auger Drilling Rig For Sale
Ingersoll-Rand TH60 Drilling Rig - For Sale
Schramm T985HA Rotadrill Rig for Sale
Schramm T130 Drill Rig - Range III Telescoping Mast for Sale
Schramm T130 Drill Rig for Sale
VFD Land Rig - 3000hp - for Sale
LS National Oilwell New SCR Land Rig - 2000hp - for sale
Ingersoll-Rand T4BH (Blast Hole) Drill Rig for Sale
Bomco VFD AC New Rig - 2000HP
SCR Gardner Denver Drilling Rig - 1000HP - for Sale
National 80UE - 1000 HP SCR drilling rig for sale
LCI 750 Drilling Rig - 1000 HP - for Sale
Mechanical Trailer Package - 1000HP
Ingersoll-Rand RD20 Range III Drill Rig - 2002 built - for Sale
Ingersoll-Rand T3W Drilling Rig For Sale
Mechanical Used Land Rig - 1500HP - For Sale
RD20 Range III Land Rig For Sale
Continental Emsco GC 500 - 10,500feet - 1000hp Used Land Drilling Rig
Land Rig - Used - 2000hp - for sale
Schramm T450M Drilling Rig - For Sale
Ingersoll-Rand TH60 Drilling Rig - For Sale
Driltech D40K Drilling Rig - For Sale
Speedstar 30K Drilling Rig - 1985 Built - For Sale
Driltech D25 Drilling Rig 2001 Built for Sale
Ingersoll-Rand T4W Drilling Rig - For Sale
Speedstar SS210 Drill Rig for Sale
Schramm TXD Drilling Rig Package - For Sale
Ingersoll-Rand RD10 Rig Package for Sale
Driltech T25K3W Drilling Rig for Sale
Chicago-Pneumatic 650 Drill Rig for Sale
Midway 500 Drilling Rig - For Sale
Ingersoll-Rand T3W Drilling Rig - For Sale
Howard Turner 1500 Drill Rig for Sale
Ingersoll-Rand T3W Drill Rig for Sale
Nordic Drill DRC-10-A Crawler Drill Rig for Sale
Ingersoll-Rand CM-780D Blasthole Drilling Rig - For Sale
Schramm T64HB Drill Rig - For Sale
Ingersoll-Rand TH75W Drill Rig - For Sale
Speedstar Quickdrill Drilling Rig - For Sale
Atlas Copco Boomer L2C Drilling Rig - For Sale
Soilmec SR45 Drill Rig for Sale
Acker Soilmax Crawler Drill Rig for Sale
Schramm TXD Drilling Rig Package - For Sale
Failing 1250 Drill Rig & Water Truck for Sale
Gardner Denver 1500 Drilling Rig - For Sale
Versa Drill V - 1040 - DP Drilling Rig for Sale
Failing CF-15 Drilling Rig - For Sale
Generic Hydraulic Crawler Drill Rig and Air Compressor - For Sale
Generic Bucket Style Drilling Rig - For Sale
Atlas Copco T4W DH Drilling Rig - For Sale
Schramm T64HB Drilling Rig for sale
Kyle 12K - Drilling Rig for Sale 1996 Built
Simco 2800 Drilling Rig for Sale
Schramm T64HB Drilling Rig - For Sale
Ingersoll-Rand T4BH (Blast Hole) Drilling Rig - For Sale
Schramm T64HB Drilling Rig - For Sale
Schramm T64HB Drill Rig Drill Rig For Sale
Ingersoll-Rand T4W Drill Rig for Sale
Ingersoll-Rand T3W Drill Rig for Sale
Ingersoll-Rand RD20 Range II Rotary Drill Rig for Sale
Driltech T25K5W Drill Rig - 2007 Built - for Sale
Canterra CT 250 Drill Rig for Sale
Ingersoll-Rand TH75 Used drilling rig for sale 1991 Built
CME-92 Drill Rig - for Sale
Versa Drill V-1040DP Drill Rig - for Sale
Ingersoll Rand RD20 Range III Drill Rig for Sale
Soilmec R-620 Crawler Drilling Rig - For Sale
Driltech D40K Used Drill Rig for sale
Ingersoll-Rand T3W - Long Tower - Drilling Rig - 1990 Built
Schramm T500XD Drilling Rig - For Sale
Sanderson-Cyclone Drill Co. 36-R Drill Rig & Package for Sale
Speedstar 275 DSI Quik-Drill Rig 1989 Built for Sale
Ingersoll-Rand TH75W Drill Rig - For Sale
Ingersoll-Rand T4W DH used drill rig 1988 Built- For Sale
Schramm T130 Drilling Rig - For Sale
Foremost Barber DR12 PTO Drilling Rig - For Sale
Cyclone 35R Drilling Rig for Sale
Generic MC 900 P Drilling Rig - For Sale
Ingersoll-Rand DM25 Used Drilling Rig 1985 Built - For Sale
Reichdrill T690 Drilling Rig - For Sale
Failing Holemaster 3000-CF Drill Rig for Sale
Versa-Drill V2000 Drilling Rig - For Sale
Schramm T985 Drilling Rig for Sale
Watson 1500 Drill Rig for Sale
Failing CF-15 Drill Rig for sale
Cabot 900 Series - 900hp Drilling Rig for Sale
Self Elevating Drilling Rig - 1500HP for sale
Atlas Copco RD20 Range III Drilling Rig - For Sale
Schramm RC685 Exploration Drilling Rig - For Sale
Atlas Copco T4BH (Blasthole) Drilling Rig - For Sale
Reichdrill T650 BH Drilling Rig for Sale
CME 850 Drilling Rig - For Sale
Cardwell KB200C Workover Rig for Sale or Charter - 81 Ton
Failing 1250 Drilling Rig for Sale
Canterra CT250 Torquemaster Series Monitoring Drilling Rig - For Sale
Schramm T450BH Driling Rig - 2004 Built - For Sale
Chicago Pneumatic T650 Drilling Rig - For Sale
Ingersoll-Rand RD20 Range II Drill Rig for Sale
Ingersoll-Rand T3 (Truckn 3) Drill Rig - 1975 built - for Sale
Atlas Copco T30 Power ROC Crawler Drilling Rig - For Sale
Ingersoll-Rand T4W 1986 Built Drill Rig for Sale
Generic 913 Cubex Drilling Rig - For Sale
Chicago Pneumatic CP650W Drilling Rig - For Sale
Ingersoll-Rand TH60 Long Tower Drilling Rig - For Sale
Gardner Denver 2000 Drilling Rig for Sale
Ingersoll-Rand T3W Drilling Rig - 1987 built - for Sale
Schramm T64HB Drilling Rig - For Sale
Ingersoll-Rand T3W Drilling Rig - 2004 Built - For Sale
CME 55 Crawler Drilling Rig For Sale
Ingersoll-Rand DM45E Built 1994 Drilling Rig for Sale
Generic Larson Reverse Rotary Drilling Rig for Sale
Ingersoll-Rand T3W DH (Deep Hole) for Sale - 1998 Built
Portadrill TLS 471 Drill Rig for Sale
Schramm T450 Drilling Rig - For Sale
Speedstar DSI QuikDrill Drilling Rig - For Sale
Atlas Copco T4BH (Blasthole) Drilling Rig - For Sale
National 1320 UE Skid Mounted Electrical Rig for Lease - 2000hp
Electrical AC/SCR Drilling Rig for Charter - 1500hp
Sterling CH7 Caisson Drill Rig - 1984 Built - For Sale
Gus Pech Brat 22R Drill Rig For Sale
IDECO H 1000 Used Drill Rig with Oil & Gas Package for Sale
Cardwell 50MT R2 Workover Rig for Sale
2000hp National 1320-UE for Hire
Mechanical Skid Mounted Drilling Rig - 1000hp for Sale
2000 hp Gardner Denver 1500-E Drilling Rig for Hire
2000HP Oilwell 2000-E Drilling Rig for Rent
Schramm T64HB Drill Rig for sale
Simco 2400 SK-Drilling Rig - For Sale
Ingersoll-Rand T4W Drilling Rig for Sale
Schramm T64HB Drilling Rig - For Sale
Ideco H 44 Model - 750 HP 6 axle Trailer mounted Rig for Sale
Ingersoll Rand 6 axle Trailer Mounted Rig - 750hp
Electrical Drilling Rig Taylor 350 HP - Trailer mounted - For Sale
Ingersoll-Rand ECM 370 Crawler Drilling Rig - For Sale
Bauer BG11H Crawler Drilling Rig - 2015 Built - For Sale
Mechanical Drilling Rigs - 1500HP - for Sale
Gardner Denver 14W Drilling Rig - For Sale
Sandvik T1000 BH Drilling Rig - For Sale
Atlas Copco L830 Crawler Drilling Rig - For Sale
Driltech / Sandvik T25K5W Drill Rig for Sale
Ingersoll-Rand DM25SP, Rotary Blast hole Drill Rig - 1996 Built for Sale
Speedstar SS200 Drill Rig for Sale
Speedstar SS-210 Rotary Drilling Rig - For Sale
Hopper GXXTA D/D Back-In Well Service Rig for Sale
Schramm T450 Drill Rig - 1988 built - for Sale
Ingersoll-Rand TH60 Long Tower Drilling Rig - For Sale
2015 Rebuilt T4W DH Drill Rig for Sale
National 1320 UE Drilling Rig for Sale
Drilling Rig 13,000' Capacity - for Sale
National 1320 UE SCR Land Rig 2000 HP for sale
Carrier Mounted Rig - 650hp for Sale
Service King - SK 775 Series - 1000hp Drilling Rig for Sale
NOV-1500 UE Drilling Rig for Sale
National 110 UE 1500 HP SCR Drilling Rig for Sale
Gardner Denver 700 Mechanical Drilling Rig for Sale
National 1320 UE 2000hp Drilling Rig - Newbuild
Ideco Trailer Mounted Drilling Rig H 44 for Sale
Ingersoll Rand 750hp Trailer Mounted Drilling Rig
Skytop Trailer Mounted Rig - 650hp for Sale
Reedrill SKT Drilling Rig for Sale
Chicago Pneumatic 600 Drilling Rig - For Sale
Speedstar Mini-Star Drilling Rig For Sale
Franks 658 Drilling Rig for Sale
CME 55 Drill Rig for Sale
Acker Soil Scout Track Mounted Drill Rig - for Sale
Ingersoll-Rand TH60 Drilling Rig - For Sale
Ingersoll-Rand DM25SP Rotary Blast hole Drill Rig - 1994 Built for Sale
Chicago Pneumatic T670W Drilling Rig - For Sale
Ingersoll-Rand Range II RD20 Drilling Rig - For Sale
Ingersoll-Rand TH55 Drilling Rig - For Sale
Chicago-Pneumatic 650 Drill Rig for Sale
Schramm T64HB Drill Rig - for Sale
CME 75 Drill Rig for Sale
Schramm T64HB Drilling Rig - For Sale
Failing 1500 Holemaster Drilling Rig - For Sale
Failing Holemaster 1000 Drilling Rig - For Sale
CME 75 Drill Rig - 1987 Built - for Sale
Mobile B53 Auger Drilling Rig - For Sale
Chicago Pneumatic T650W Drill Rig for Sale
Mobile B-59 Drilling Rig for Sale
CME 55 Drilling Rig - For Sale
Chicago Pneumatic T650 Drill Rig for Sale
Mobile B61 HDX Drilling Rig for Sale
Chicago Pneumatic 670 Drilling Rig - For sale
CME 55 Drilling Rig for Sale
Reichdrill T625W Drilling Rig for Sale
Atlas Copco RD20 Range III Drilling Rig - For Sale
Atlas Copco T4W Drilling Rig - For Sale
Driltech T40KW Range II Drill Rig on 4-Axle Carrier - 2015 Built - for Sale
Spencer Harris 7000 Mechanical Drilling Rig for Sale
Skytop Brewster TR800 - 900hp Drilling Rig for Sale
Gardner Denver 500 - Mechanical Drilling Rig 700 hp - for Sale
Schramm TH130 Drilling Rig for Sale
Oilwell 76 Land Drilling Rig for Sale
Wilson Mogal 42 Workover Rig - 350 Hp - for sale
Trailer Mounted New Drilling Rig 1000hp for Sale
Schramm T685DHH Drill Rig for Sale
Skytop Brewster N75 - 1000 HP Mechanical Drilling Rig - for Sale
Driltech T25K2W Drilling Rig - For Sale
Driltech D40K Drilling Rig - For Sale
National 1320 - 2000 HP Drilling Rig for Sale
MAC 400 - Mechanical Drilling Rig 450 hp for Sale
National 55 800 hp Mechanical Drilling Rig for Sale
Continental Emsco A550 Used SCR Electric Drilling Rig for Sale
Mobile B-61 HDX Drilling Rig - For Sale
LCI 1000 Mechanical Carrier Mounted Drilling Rigs for Sale
Cooper LTO 150 Drill Rig for Sale
DeepRock DR-150 Drill Rig For Sale
Crown CE750 Trailer Mounted Drilling Rig for Sale
Ideco H44 Carrier Mounted Drilling Rig for Sale
F200-DEC - 1780 hp Mechanical Land Drilling Rig for Sale
Chinese RG 1300 Triple - Trailer Mounted Mechanical Drilling Rig - for Sale
SK Series 6- Axle Back in Carrier Mounted Drilling rig for sale - 750HP
Chinese RG 1300 Double - Mechanical Drilling Rig for Sale
Ideco H44 Carrier Mounted Drilling Rig for Sale
Gardner Denver 1100 - 1500 hp Mechanical Drilliing Rig for Sale
SEDLAR 160 - Self Elevating Drilling Land Rig - 1000 hp for Sale
Schramm T64HB Drilling Rig - For Sale
OIME 2000 Land Drilling Rig - 2000 hp for Sale
National 1625 - 3000 HP - Drilling Rig for Sale
Walker Neer 250-40 Truck Mounted 7,000 Drill Rig for Sale
Brewster N42 900 HP Mechanical Drill Rig for Sale
National 1320 - 2000 hp SCR with Top Drive - Drilling Rig for Sale
Ideco 725 - 750 HP SCR Drilling Rig for Sale
Atlas Copco T4BH (Blasthole) Drilling Rig - For Sale
Crown Duke CE 750 SD Drill Rig for Sale
OIME 2000 Drilling Rig for Sale
Superior 1000M Drilling Rig for Sale
Ideco 725 - 750 HP SCR Drilling Rig for Sale
Brewster N42 900 HP Mechanical Drill Rig for Sale
Walker Neer 250-40 Truck Mounted 7,000 Drill Rig for Sale
National 1320 - 2000 HP Drilling Rig for Sale
National 1320 - 2000 hp SCR with Top Drive - Drilling Rig for Sale
Gardner Denver GD500 Drilling Rig - 600 HP for Sale
Unit U40 - 1100 HP Mechanical Drilling Rig for Sale
IDECO H37 Trailer Mounted Drilling Rig for Sale
Superior 700 Mechanical Land Drilling Rig - 800 HP - for Sale
Ideco U-15 - 800 HP Used Drilling Rig
Gardner Denver S1000 Mechanical Drilling Rig for Sale
Gardner-Denver 1100 Land Drilling Rig
Gardner Denver 800 Land Drilling Rig for Sale
Gardner Denver 800 Mechanical Land Drilling Rig for Sale
Gardner-Denver 700 Land Drilling Rig for Sale
National 55 Land Drilling Rig for Sale
OIME HH500 Electric Land Drilling Rig for Sale
National 55 Double Drum 1000hp Rig for Sale
National T45 Electric Land Drilling Rig for Sale
Superior 700 UE 750hp Electric Land Drilling Rig for Sale
Gardner Denver 700 Mechanical Land Drilling Rig for Sale
Gardner Denver 800 Land Drilling Rig for Sale
Wilson 65 Mechanical Drilling Rig for Sale
RT - 400B 12,000 feet Drilling Rig for Sale
Spencer Harris 7000 Trailer Mounted Drilling Rig
Spencer Harris 7000 Drilling Rig for Sale
SK675 Carrier Mounted Drilling Rig for Sale
Gardner Denver DW 500 Drilling Rig for Sale
2005 Foremost CTR Single Coil Tubing Hybrid Drilling Rig
Gardner Denver 700 Drilling Rig for Sale
Drillmec HH 300 Drilling Rig for Sale
Crown 1000 Drilling Rig for Sale
Ideco H37 - 600hp - Drilling Rig for Sale
Ideco H35 - 600 hp - Drilling Rig for Sale
Ideco BIR 800 Drilling Rig for Sale
4 new Heli-transportable AC electric rig for sale
Cabot 1500Hp Rig for Sale
IDE AC 1500 Sparta Drilling Rig for Sale
Spencer Harris 7000 Drilling Rig for Sale
Drilling Structures 800hp Rig for Sale
ZJ-40 Drilling Rig for Sale
Refurbished Wilson Mogul 42B Mounted Truck Well Service Rig for Sale
Cabot 900 Drilling Rig for Sale
Crown CE900ESD Trailer Mounted Rig for Sale
JC40 DB Land Drilling Rig for Sale
Oilwell 760E 1000hp Drilling Rig for Sale
National 80B Land Drilling Rig for Sale
Lewco Cameron LDW 750K Drilling Rig for Sale
National 610-E 750 HP Drilling Rig for Sale
Oilwell E2000 Drilling Rig for sale
Drillmaster 1200 Drilling Rig for Sale
Brewster N4 on Spencer Harris Drilling Rig for Sale
MD Cowan (Rig Tech RT 400B) Drilling Rig for Sale
Cooper 750 Drilling Rig for Sale
Witchtex R-4 Trailer Mounted Drilling Rig for Sale
OIME TBA 2000 Heli Rig for Sale
National 110 Drilling Rig - 1500hp - for Sale
Ingersoll Rand T4W Drilling Rig for Sale
Top Oilfield Triple 1500hp SCR Rig for Sale
Schramm Rotadrill TDX 750hp for sale
MD Cowan Super Single 1000hp SCR Rig for Sale
MD Cowan Super Single Land Rig for Sale
Fast Desert Moving Rig for sale
Top Oilfield Triple 1500hp SCR Rig for Sale
2009 Built MD Cowan Super Single Rig for sale
OIME 3000 Drilling Rig for Sale
CABOT 1200 Trailer Mounted Drilling Rig for Sale
1976 Speedstar SS-22 - Cummins Powered Drilling Rig for Sale
Ingersoll-Rand T3W Drilling Rig - For Sale
IDECO H44 Truck Mounted Drilling and Work-Over Rig for Sale
Rig Master E90 DC Drilling Rig For Sale
Service King 775 Carrier Mounted Drilling Rig For Sale
Backyard Equipment Package - For Sale
Trailer Mounted Super Single Slant Rig for Sale
Trailer Mounted Telescopic Mast, Double Rig for Sale
Trailer Mounted Telescopic Mast Rig for Sale
Trailer Mounted Hydraulic Lift, Super Single Rig for Sale
Trailer Mounted Hydraulic Lift, Super Single Rig for Sale
Trailer Mounted Hydraulic Lift, Super Single Rig for Sale
550HP Trailer Mounted Hydraulic Lift Drilling Rig - For Sale
550HP Trailer Mounted Hydraulic Lift, Super Single Rig for Sale
National Drilling Rig for Sale
Trailer Mounted Rack & Pinion, Super Single Rig for Sale
Parallelogram Style Drilling Rig - For Sale
Parallelogram Style Drilling Rig - For Sale
850HP Trailer Mounted Rack & Pinion Rig for sale
850HP Trailer Mounted Rack & Pinion Rig for sale
10,000ft Drilling Depth Super Single Rig for Sale
700HP Trailer Mounted Rack & Pinion, Super Single Rig
Parallelogram Style Drilling Rig - For Sale
850HP Trailer Mounted Rack & Pinion Rig for sale
IDM 1500 HP Drilling Rig for Sale
Chicago Pneumatic T650 Drilling Rig - For Sale
Carrier Mounted 550HP Telescopic Mast Rig For Sale
Carrier Mounted 550HP Telescopic Mast Rig
2012 Built Platform Style Telescopic Mast, Double Drilling Rig
Used Carrier Mounted Telescopic Mast Drilling Rig
2012 Built Carrier Mounted 550HP Telescopic Mast Rig for Sale
1600HP Sling Shot, Skidding, Triple Drilling Rig for Sale
3000HP Swing Lift Triple Drilling Rig for sale
Sling Shot Bi-directional Skidding Triple Drilling Rig for Sale
Portadrill 10TG Drill Rig - For Sale
Gus Pech Drilling Rigs - For Sale
Nordic Drill DRC-10-A Crawler Drill Rig For Sale
Soilmec SR50 Drilli Rig For Sale
Soilmec SR30 Drilling Rig - For Sale
2000HP Swing Up Triple Drilling Rig for sale
2000HP Swing Up Triple Drilling Rig for sale
Sling Shot Hydraulic Lift Triple Drilling Rig for Sale
Cantilever Mast on Dolly Hydraulic Lift Triple Rig for Sale
2013 Built Swing Lift Triple Drilling Rig for Sale
Parallelogram Style Land Drilling Rig for Sale
2013 Built Carrier Mounted Telescopic Mast for Sale
1000Hp Parallelogram Style - Telescopic Mast Double Rig
1000Hp Parallelogram Style - Telescopic Mast, Double Rig
2013 Built Carrier Mounted Telescopic Mast for Sale
Reichdrill C-700 Crawler Drilling Rig - For Sale
Texoma 600-30 Foundation Drilling Rig for Sale
Mobile B61 HDX Drilling Rig - For Sale
Mobile Drill B-57 Auger / Coring Drilling Rig - For Sale
Mobile B53 Diamond Core Drilling Rig - For Sale
550HP Carrier Mounted Drilling Rig for Sale
650HP Carrier Mounted Drilling Rig for Sale
350HP Telescoping Style Rig For Sale
1997 Built Trailer Mounted Super Single Slant Rig for Sale
Cantilever Mast on Dolly Hydraulic Lift Triple Drilling Rig
OIME SL-7 Drilling Rig For Sale
Corsair 550Hp Drilling Rig For Sale
NOV 1500 HP SCR Drilling Rig for Sale
IRI 1100Hp Trailer Mounted Telescopic Drilling Rig for Sale
TT Sense Trailer Mounted Drilling Rig for Sale
TSM 850 Trailer Mounted Drilling Rig - For Sale
MD Cowan Trailer Mounted Drilling Rig for Sale
Cooper Drilling Rig for Sale
Chicago Pneumatic 650 S/S Drilling Rig - For Sale
Chicago Pneumatic 650 Drilling Rig - For Sale
Chicago Pneumatic 670 Drilling Rig - For Sale
LTI 1000KP Drilling Rig - 2000Hp - For Sale
Mobile B-53 Drilling Rig - For Sale
Reichdrill T-650-W Drilling Rig - For Sale
NOV Rapid Drilling Rig for Sale
Service King 1000 HP Drilling Rig - For Sale
Trailer Mounted Telescopic Mast, Double Rig - For Sale
2000HP VFD Land Drilling Rig for Sale
2000HP Electric SCR Rig for sale
Crown Duke CE 750 SD Trailer Mounted Drilling Rig For Sale
Davey M8 Table Drive Drilling Rig for Sale
Davey M8A Table Drive Drilling Rig for Sale
Gus Pech KH-48 Super George Drilling Rig - For Sale
Gus Pech 900XHR Drilling Rig - For Sale
Howard Turner HTB3KDD Drilling Rig For Sale
2007 Built VFD Land Drilling Rig for sale
Sonic SDC500-29P Drilling Rig for Sale
Diedrich D120 Drilling Rig - For Sale
Sonic SDC500-29P Drilling Rig - For Sale
Mayhew 1000 Drilling Rig - For Sale
Chicago Pneumatic T650WS Drilling Rig - For Sale
Jaswell J1200 Drilling Rig - For Sale
Drillmax 250 Well Drilling Rig - For Sale
Bucyrus Erie 60L Cable Tool Drilling Rig - For Sale
PortaDrill TLS Drilling Rig - For Sale
Schramm T450WS Drilling Rig - For Sale
Ingersoll-Rand CM-780D Blasthole Drilling Rig - For Sale
Gill-Beetle Track Drilling Rig - For Sale
Schramm T64HB Drilling Rig - For Sale
Simco 2800 HSHT Drilling Rig - For Sale
DW400C Hydraulic Drill Rig - For Sale
Midway 1500 Drilling Rig for Sale
Mayhew 500 Drilling Rig - For Sale
Gardner Denver 14W Drilling Rig - For Sale
Gardner Denver 2500 Drilling Rig - For Sale
Simco 2800HT Drilling Rig for Sale
Gardner Denver 1000 Drilling Rig - For Sale
Geoprobe 8150LS Crawler Drilling Rig -For Sale
Speedstar Drilling Rig - For Sale
Gefco Speedstar 185K Drilling Rig - For Sale
Generic LTD 360 Cable Drilling Rig - For Sale
Oilwell E2000 Drilling Rig - For Sale
NOV 1000 HP AC/VFD Drilling Rig - For Sale
Davey Rotary Table Drilling Rig - For Sale
Cooper 350 Drilling Rig for Sale
Victory Trailer Mounted Telescopic Mast, Double Rig - For Sale
Carrier Mounted Corsair 550HP Rig for Sale
National 650HP Drilling Rig for Sale
Alta 1500 HP AC/VFD Drilling Rig for sale
Foremost DR-24 Drilling Rig - For Sale
Ideco Rambler Workover Rig for sale
National Oilwell Model 5C Five Axle K100C Carrier Workover Rig - For Sale
500HP National 5C Workover Rig for Sale
Reconditioned Skytop Brewster Model TR-800 Drilling Rig
1500HP Lewco/Cameron LDW 750K Rig
National 610E Drilling Rig - For Sale
Ideco Backin Rambler Workover Rig for Sale
Precision 750 HP SCR Rig for sale
2002 Built Dreco Rig for Sale
National Oilwell 5C Workover Rig for Sale
IMT AF18 Crawler Drilling Rig - For Sale
JC 50D SCR Drilling Rig for Sale
Simco 2800 Drilling Rig - For Sale
National 1320 2000 HP Drilling Rig - For Sale
PortaDrill TLS Top Head Drilling Rig - For Sale
Wilson 42 - 110 Double Trailer Mounted Rig - For Sale
LTO 350 & 550 Cooper Copy Workover Rig - For Sale
Canterra CT-350 Drilling Rig - 1989 Built - For Sale
Gus Pech 1000R Drilling Rig - For Sale
Foremost CTR Single Coil Tubing Hybrid Drilling Rig for Sale
Portadrill 524-3A Drilling Rig - For Sale
UDR 1500 Range III Mobile Drilling Rig - For Sale
Davey Rouselle M8A Drilling Rig - For Sale
450 t Hydraulic Land Drilling Rig for Sale
PortaDrill 524 Drilling Rig for Sale
Gardner Denver 1500 Drilling Rig - For Sale
1500 HP Mechanical Land Rig for Sale
Deep Rock DR150 Drilling Rig - For Sale
Davey Rouselle M8A Drilling Rig for Sale
Tech RT 400 Hydraulic Drilling Rig - For Sale
3000HP Electric Deep Drilling Rig - For Sale
1500HP Electric Drilling Rig - For Sale
New Electric Land Drilling Rig for Sale
Bucyrus Erie 10R Table Drive Rotary Drilling Rig - For Sale
Joy MS-4E Top Hammer Air Driven Drilling Rig - For Sale
Ideco 2100E Rig - For Sale
Hydraulic Super Single TXD 200 Rig - For Sale
Schramm T64HB Drilling Rig for Sale
Schramm T500XD Trailer Mounted Drilling Rig for Sale
Taylor 500 Well Service Rigs - For Sale
Ingersoll Rand DM30 Drilling Rig - For Sale
National 1320 2000 HP Drilling Rig - For Sale
Schramm T450H Drilling Rig - For Sale
Gus Pech KH-48 Super George Drilling Rig - For Sale
Gus Pech G-48 Super George Drilling Rig - For Sale
New Derex 1340 DR Drilling Rig - For Sale
Schramm TXD 200 Trailer Mounted Drilling Rig - For Sale
Schramm TXD 200 Trailer Mounted Drilling Rig for Sale
Crown 750 Trailer Mounted Drilling Rig for Sale
Watson Hopper Corsair 400 Drilling Rig - For Sale
Pump Hoist Rig - For Sale
CME 850 Drilling Rig - For Sale
10T Pump Hoist Rig for Sale
Sandvik Titan 600 Rock Dilling Rig for Sale
Sullivan TCD918E Drilling Rig - For Sale
Derex 2630-22 MATH Drilling Rig - For Sale
Derex 2630-22 Arthur Drilling Rig - For Sale
Derex 1340-16 DR (Dual Rotary) Drilling Rig - For Sale
Ardco K10 4X4 Drilling Rig - For Sale
Derex 1340-14X DR (Dual Rotary) Drilling Rig - For Sale
Derex 1340-14 DR (Dual Rotary) Drilling Rig - For Sale
Brand New Massenza Hydraulic Drilling Rig Model Mi8 Mounted On Tracks (Crawler)
Brand New Massenza Hydraulic Drilling Rig Model Mi5 Mounted On Tracks (Crawler)
Derex 1340-12X DR (Dual Rotary) Drilling Rig - For Sale
Ideco E-1200 Drilling Rig - For Sale
Continental EMSCO Drilling Rig - For Sale
Continental EMSCO Drilling Rig - For Sale
IDM Drilling Rig - For Sale
IDM Drilling Rig - For Sale
1200T SWL Pedestal Crane - For Sale
Geoprobe 54DT Soil Sample Drilling Rig - For Sale