Worldrigs ID: WR674

LCI 750 Drilling Rig for Sale
Carrier Mounted Drilling Rig for Sale
1000 HP drilling rig for sale

Introduction :
The rig is a loadcraft industries 750 drilling rig with mast hook load capacity of 365.000 lbs
(160 metric ton), powered by two caterpillar C15 diesel engines, coupled two allison 6061 RB
transmissions with torque converter. The mast is 114ft (36m) rated at 365.000 lbs API capacity.
Drawworks have 1000hp capacity. All equipment is mounted on a 7 axle carrier. The rig is
equipped with a telescoping substructure at 17ft 6 inches (5.3m) height.
The mast is equipped with a torque arrest beam for the top drive and with piping and necessary
loops to operate the top drive. The total rig is built for extremely quick rig up/down time.
The TD is a northdrill API 250 ton rated with continuous torque rating of 40.500 ft-lbs.
All necessary equipment to operate the top drive in is included with the rig.

1. Carrier
Section 1.1 carrier
- Seven axle heavy-duty carrier for load of 140.000 lbs. Fully equipped with lights and brakes
etc for normal driving operation. All axles have spring brake chambers for safety.
- Tires and wheels are disc wheels, 14"20 all terrain tread. Tire rating of 52.000 psi total.
Two spares delivered.
- Two 100 gallon (2x420 L) fuel tanks side mounted on carrier frame, connected for equalization.
- One toolbox storage box of steel with reinforced lockable doors.
- Eight side platforms with handrails on both sides along the carrier body, four on each side.
Each platform is approx. 6ft x 2 ft (1,8x0,6m)
- One staircase section from side platforms to ground level.
- Hercules 129 HA deadline anchor to be used with compression type weight sensor. Drum type
mounted on carrier frame in front of drawworks frame, hydraulic sensor included.
- Four pedestals to go under front jacks for rig stability.
- Total of six jacks for leveling the rig.

Section 1.2 hydraulic system
- 50 GPM (190 LPM) hydraulic system, design to operate at minimum 2000 psi with rating of
50 gpm at 2100 psi.
- Hydraulic pump driven from PTO on transmission.
- Air activated clutch for pump engagement.
- 325 gallon (1230 L) hydraulic oil tank with filler cap, breather, oil level, oil temp.

Section 1.3 tong circuits
- Tong hydraulic circuit is designed to operate up to 50 gpm at 2000 psi.
- Includes connectors, pressure & return lines, pressure gauge, directional flow valve and pressure
regulating valve.

Section 1.4 handling winch
- Hydraulic powered planetary winch 8000 lb (3.6 t) line pull, rated at 100 ft (30m) per minute at
2000 psi hyd. pressure.
- 325 ft (99m) of 1/2" line on drum
- Fail safe brake (in/out hydraulic activated)
- Winch sheaves provided in crown
- Protection cage on winch
- Controls at operators console

2. Main power/engine
Section 2.1 engine/transmission
-Two caterpillar C-15 540 hp diesel engines
- Equipped with limiting speed governor, air throttle sctuator, lube and fuel filters, alternator and
flywheel housing.
- High ambient radiators and suction fan, permanent type anti-freeze, signel exhaust with spark
arrester diverted to off-operator side with mufflers.
- Engine kill valve located at operators console
- Electric start (remote from operators console)
- Both engines can run at the same time or only one if adequate.

Section 2.2 transmission
- Allison S 6061 RB model six-speed transmission (five fwd 1 rw)
- With converter and oil cooler
- Air over hydraulic controls, with air line indicator system
- Controls available at operators console and in drivers cabin

3. Drawworks
Section 3.1 drawworks
- Model 4212 drum winch assembly
- Full air, fawick "28VC-1000" clutch outside drawworks frame.
- Brakes are 42" (107 cm) diameter x 12" (30,5 cm) wide, lined with 1 inch (2,5 cm) x 12" (30,5 cm)
- API driled brake blocks, full wrap dead-end equalized
- Brake rims are removable with rings for splash water cooling
- Brake operatoin shafts are mounted on ball bearings; these are self engaging and release
by operator.
- Drum barrel is 18" (45,7 cm) in diameter, and 38" (96,5 cm) long, mounted on double row
self-aligning spherical roller bearings on a 6 1/2" (16,5 cm) drum shaft
- Clutch single line pull is 42.500 lb on bare drum and first gear.

Section 3.2 lubrication
- Centralized lubrication system to all bearings and brake linkage on drawworks, is located
outside frame.

Section 3.3 brake water cooling
- Closed loop brake cooling system, mounted on carrier
- Includes 425 gallon tank with covered top, with level indicator
- Removable cap with drain system, breather and fill cap.

Section 3.4 drawworks drive
- ASA-100-3 (1 1/4") pitch, triple stand, roller chain
- Chain drive from input sprocket to sprocket on jackshaft
- ASA-100-3 (1 1/4") pitch, triple stand, roller chain as final drive to main drum

Section 3.5 main drum - grooved jacket
- Lebus counter balanced sleeve is grooved for 1 1/8" wireline, to assist spooling, and reduced line wear.

Section 3.6 hydrotarder
- Parmac 202 hydrodynamic brake assembly with dual rotary
- Fawick 28 VC 1000 air clutch, gates, inlet air valve and piping
- 325 gallon (1230 L) water tank, lines, valves and plumbing installed on rig.
- Drive from the main drum thru triple stand 1 1/4" pitch drive chain.

Section 3.7 combined gearbox
- Cushman model 279 combined gearbox consisting of right angle gearbox and dropbox.
- Right angle gearbox ratio 1:1 to drive single drum drawworks. Dropbox to transfer torque to rotary.
- Pressurized lubrication system.

Section 3.8 sandline drum
- Sandline drum with 42x8 brake size, for handling 16,500 ft of 9/16" wireline on drum
- Brakes are removable for water splash cooling of the brake rims
- Single line pull is 26,000 lbs on the drum

Section 3.9 rotary drive
- Provided at the dropbox for power connection- Elevated chain drive is oil bath type consisting of drive
sprocket at bottom of case with ASA 140-2 (1 3/4") pitch double

4. Mast
Section 4.1 mast
- 114 ft (33,5m) clear working height with an API rated static hook load of 330.000 lb with 8 lines,
and 365.000 lb with 10 lines.
- Designed to withstand 69mph winds from any direction
- Telescoping twin box structure designed and built to API standards.
- Two section with upper section telescoping into lower section for rig move operation.
- Automatic mast latching in raised or lowered position
- Lock and operating control located at base of mast
- Ladder from base to crown with safety blocks for personnel
- All necessary chains, turnbuckles, pins etc included and certified
- 4 inch standpipe rated 5000 lb, welded with 1502 unions.

Section 4.2 crown assembly
- Bender crown arrangement for 8 or 10 lines string up with conventional block.
- One 36" fastline sheave, grooved for 1 1/8"
- One 36" deadline sheave, grooved for 1 1/8"
- Four 30" sheaves cross mounted, grooved for 1 1/8"
- Two catline sheaves
- Crown sheaves are steel with flame hardened grooves.
- Sheaves are mounted on timken tapered roller bearings and all carry certification.
- Crown platform with railing for personnel safety
- Attachment point for four wind guylines from crown to ground is provided.

Section 4.3 tubing board
- All welded construction
- Automatically raised or lowered at mast telescoping
- Mounted at 55 ft above setback
- Board fingers are for 17.000 ft of 2 7/8",  or 11.400 ft of 3 1/2" tubing
- 2 ft 6 inch wide tubing board walkway
- Handrails at board outside
- Attachment points for safety line (escape line) at each corner.

Section 4.4 weight indicator
- Weight indicator complete with sensor
- 12" dial indicator
- Box mount with 25ft of hose assembly
- Calibrated in NM and LBS
- Charts for 6, 8 and 10 lines on indicator

Section 4.5 crown saver
- Load and crown saver installed on drawworks
- Automatically disengages clutch and sets drawwork brakes if block comes too close to crown.

5. Substructure
Section 5.1 hydraulic telescoping substructure
- Working floor height of 17,5 ft (5,3m) with 14 ft in clear under rotary beams
- 4,5 ft is the maximum height when scoped down for transportation
- 10ft 6 in max width when scoped down
- Capacity of 365.000 lbs (160 mt) on rotary beams and 225.000 lbs (100mt) at setback
- Sub base is equipped with fold out wings, total floor area is 18ft wide x 18ft long
- Handrails with toeplate surrounding the entire floor
- One stairway from floor to carrier level
- Pipe ramp with steel plating
- Setback covered with 3" oak timbers
- Two tong backup poles in drilling configuration
- Rat and mousehole access
- BOP handling system with to rails integrated under the floor. Each rail rated at 5 ton.
- Carrier ramp is included with the sub, 10 ft wide to allow the rig to rest completely on the base of
the ramp. Comes in two sections.

Section 5.2 catwalk
- Catwalk assy of 4ft wide x 45 ft long x 3 ft high with built in stair , and bump post.

Section 5.3 hydraulic catworks - make & break-out
- Breakout cylinder has 6ft stroke with 20.000 lb maximum line pull
- Makeup cylinder has 6ft stroke with 20.000 lb maximum line pull
- Cylinder mounted in lower mast section, and includes wireline, turn back sheaves and plumbing
for hydraulics
- Both cylinders are controlled from operators console

6. Top drive
Section 6.1 TD power pack
- One 20ft oilfield skid power pack mounted in a weather and sound protective 30ft container.
- Main motor caterpillar C18 700 hp
- Main HPU at 550kW for TD main power, 2400 L reservoir, two main pumps
- Inline filters for all lines
- Engine driven and electric driven aux hpu for pipehandler functions
- Advanced PLC & HMI system to monitor and control TD system
- All controls integrated at operators console on rig floor
- Quick connectors for all cables and lines on TD system for quick rig up/down

Section 6.2 TD rig equipment
- Mast outfitted with piping for quicker rig up/down with the TD system
- Torque tube beam installed in the mast, and anchored to the mast lower section
- Turnbuckles, chain etc for the torque beam
- Loops from mast to TD (stays in the mast during rig move)

Section 6.3 TD hookup to rig
- The TD power pack connects to the rig by 4 hydraulic hoses that connect on ground level
at the base of the mast
- One 1/4" electrical cable is run up the mast and to the TD for control system
- Five 1/2" electrical cables is run to the operator console for TD operator control
- A power input of 440,160 or 480v to supply the system with electricity
- 1 kW is sufficient to run the system, 40 kW is needed to operate the electrical aux HPU

Section 6.4 TD main specifications
- Continuous torque rating of 40.500 ft-lbs
- Max rpm of 110 in first gear, and 180 in second gear
- Max breakout rating of 43.000 ft-lbs
- Pin connection 6 5/8 RH
- TD is equipped with onboard oil cooler
- Electric over hydraulic onboard valve section for all function control
- Onboard PLC and monitoring equipment

Section 6.5 TD pipehandler specifications
- 360 degrees free traveling orientation
- Backup tong capable of holding up to 80.000 Nm and range from 3 1/2" to 6 5/8" pipe
- Link tilt and retract function for drilling down to floor
- Integrated availability for remote operated elevator
- Upper remote operated IBOP and lower manually operated IBOP rated at 10.00 psi
- Telescopic leg for positioning of backup tong for make or break of saver sub
- Link arms 108 inch
- Manual elevator for 3 1/2" pipe
- Saver sub to 6 5/8 RH and to 5" RH

7. Additional equipment
Section 7.1 handling winch nr.2
- One additional winch equal to above listed handling winch specs

Section 7.2 V-door ramp and pipe racks
- One 48in x 3ft6in x 45ft catwalk from the rig floor level to the 42in high catwalks
- Four 42in x 28ft long pipe racks

Section 7.3 rotary table
- One 22" rotary table, 44" centers complete with split square solid steel master bushing,
spiral bevel gears, precision bearings throughout, removable box cover with lifting eyes,
positive pinion shaft lock and centralized lube system

Section 7.4 high pressure piping
- One 4" 5000 psi mud line and manifold for gauge and kill line, with 1502 union
- 4" 5000 psi standpipe on the lower mast section, with 1502 unions

Section 7.5 crown o'matic
- Combined crown and drawworks type crown-o-matic system for saving mast failures is
installed on the drawworks, and is set for locking the brakes down at activation

Section 7.6 safety chair (board escape)
- One T-bar type escape chair for tubingboard escape

Section 7.7 mast guylines
- Guylines are included, four of 5/8 lines from crown, two from board and two from the mast
mid section. All certified

Section 7.8 block hook
- One of ABCO 250 ton standard hook block
- Clevis kit for use with TD to shorten total assembly length included

Section 7.9 wire rope
- Drill line 1 1/8" wireline rope at 2500 ft, certificates provided
- Drill line spool is included at the front of the carrier by the cab
- 12.000 ft of sandline 9/16" included

Section 7.10 dead line anchor-indicator assy
- Anchor for 1,125" wirerope, for mast pull of 365.000 lbs for 10 lines string up on crown
- Anchor certified, and load cell included

ND 250 H2 (dual ratio)
- Continuous drill torque : 29.800 / 41.000 ft-lbs
- Max breakout torque : 43.000 ft-lbs
- Speed range : 0-200 rpm
- Dual ratio gearbox : Yes
- Gearbox ratio : 1:11.1 / 1:14.9
- Hydraulic motors : 2 x 320 kW max
- System total power rating : 700 hp
- Hydraulic system pressure : 6000 psi / 3000 psi
- Powering engine : C18

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.



----------------------------------------------------------------------------------------------------
Search words(for official use only) :
LCI 750 Drilling Rig for Sale
Used 1000hp Carrier Mounted Drilling rig
1000 HP Drilling Rig for Sale - LCI 750 
1000hp Land Rig Builders
1000hp Land Rig Dealers
Drilling Land Rig for Sale - LCI 750 - 1000 HP
1000HP land Rig For Sale
Carrier Mounted Drilling Rig for Sale
1000 HP Land Drilling Rig For Sale - LCI 750
----------------------------------------------------------------------------------------------------

Worldrigs ID: WR670

SCR drilling rig for sale
Used American 1000HP Land Rig
Gardner Denver 1000 HP SCR drilling rig for sale

Drawworks :
• Gardner Denver 1000 HP Drawworks with water brake.
• Powered by (1) 752 series type traction motors.

Mast :
• DSI
• 142’ x 25’ mast rated at 750,000 lb. static hookload, 500,000 lb. setback

Substructure :
• DSI
• 22’ substructure with rotary capacity at 750,000 lb. and a setback of 500,000 lb.
• Sub is a box-on-box type.

Pumps :
• Two (2) F1600 pumps
• Independently powered by two (2) 752 traction motors.
• Pumps complete with all plumbing, pulsation dampeners, and 5x6 charge pumps.

Rig Houses, tanks :
• Drillers top doghouse= 9’ H x 8’6” W x 35’L
• Mudhouse= 9’H x 10’ W x 35’ L
• Partshouse= 9’H x 10’ W x 45’ L
• Water Storage= 9’ H x 10’ W x 45’ L with two (2) 2” x 3” centrifugal pumps.
• Fueltank= 12,000 gallons

Mudsystem :
• Two 8’6” H x 10’ W x 47’ L mudtanks (1000 BBL)
• Tanks to have necessary piping, valves, dump gates, & compartments
• One 2-cone desander
• One 10-cone desilter
• Two derrick style linear shaker
• Four mud agitators with 10HP motors
• Four 5” x 6” centrifugal pumps with 75HP motors

Rotary Equipment :
• One 27-1/2” rotary table
• One 400 ton swivel
• One Varco model HD Kelly drive bushing

Traveling Equipment :
• One 400 ton block
• One set of 3 ½” x 108 elevator links

Well Control :
• One 11” x 5000 PSI annular
• One 11” double ram preventor
• One 180 Gallon Koomey type closing unit
• One Koomey type remote
• One 2” x 5000 choke manifold
• One B.O.P. lines suitcase

Instrumentation :
• One Totco type 50 weight indicator
• One Totco 100 rotary torque
• Two mudpump SPM
• One rotary RPM
• All above mounted in Totco drilling console
• Geolograph

SCR House :
• Ross Hill 3 generator x 4 SCR system
• 9’ W x 40’ L x 9’ H house

Power Equipment :
• (3) 3512 C Cats with 1050 KW generators
• Generators mounted on 10’ W x 35’ L x 9’ H skids
• (2) Gardner Denver 30 HP screw type compressors
• (1) Gardner Denver cold start compressor

Auxilliary Equipment :
• One Mathey wireline unit
• Two air winches
• Misc. set of handling tools
   (1) Spinnerhawk powertong
   (1) Kelly Spinner
   (3) 18” x 30’ pipe racks

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

----------------------------------------------------------------------------------------------------
Search Words(for official use only) :
SCR Drilling Rig for Sale
Drilling Rig for Sale - Gardner Denver 1000HP SCR
Used American Land Rigs
Used American 1000hp Drilling rig
1000HP Land Rig Builders
1000HP SCR Gardner Denver drilling rig for sale
Land Drilling Rig For Sale
Gardner Denver drilling rig for Sale
----------------------------------------------------------------------------------------------------

 

Worldrigs ID: WR569

Challenger M320 Drill Rig & Pipe for Sale
Challenger Drilling Rig package - for Sale

Model : M320 Drill Rig & Pipe
Manufacturer : Challenger
Year : N/A
Condition : Used

Description:

Challenger M320 Drill Rig & Package
Mounted on 3-axle trailer
Rig Substructure
Single piece Hydraulically raised mast 64’ x 150,000 lbs double drum
Allison transmission
18’’ rotary table (RT-18’’-2)
Kelly bar 4 ½’’ x 40’
GMC Detroit 8V92N Diesel Engine 360 HP 
 
Included as a package :
(2) Pipe Tubs with almost 5,000' ft of used drill pipe (30' x 4-1/2)
Dog house
Ideal (National supply Co)Type C-250 7-¼" x 15" Duplex Mud Pump, Skid Mounted,
Ratio : 5,64 & Rated output : 250, HP @ 60 RPM, Max 2500 lbs working pressure
Located : Europe

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.



--------------------------------------------------------------------------------------------------------
Search words(for official use only) -
Challenger M320 Drill Rig & Pipe for Sale
Challenger Drilling Rig package - for Sale
Land Drilling Rig for Sale
Drilling Rig & Pipe for Sale
Used Challenger M320 Drilling Rig for Sale
Challenger M320 Drill Rig & Pipe for Sale in Europe
--------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2227

Witchtex R-4 Trailer Mounted Drilling Rig for Sale
Trailer Mounted Land Drilling Rig for Sale

Description :

Trailer Mounted Rig:
3-Axle Back-In Trailer w/Rotary Beams
6) Hydraulic Leveling Jacks
1) Folding Walkways
1) Safety Rails and Stairways, 11R24.5 Tires, Steel Disc Wheels

Drawworks:
1) D/D Draw works, Groove F/1” Line
1) Makeup and Breakout Catheads
1) Driller’s Console w/Air Controls
1) SGL –Engine Compound P/B Detroit 8V-92 Diesel Engine
1) Allison Torque Converter 

Mast:
1) 65’H Hydraulic Raised Mast Reported 180,000 Hook Load
1) Crown Block Assembly
1) Mackissick Block/Hook Combo w/(3) Sheaves F/1” Line,
1) Baash-Ross Type DBM-330 100-Ton Block/Hook Combo w/(3) Sheaves
1) Oilwell 60-C Swivel
1) Gardner-Denver 17 ½” x 44” Rotary Table w/Split Master Bushing
1) Standpipe and Manifold
1) Rotary Hose
1) 4 ¼” Sq. Kelly
1) Baash-Ross 4 ¼” Sq. Kelly Drive Bushing

Mud Pumps:
1) Ameriam 550 6”X14” Duplex Mud Pump w/GH Mattco Fluid End,
Quick-Change Caps, Oteco 2” Shear Relief Valve Type D Pressure Guage,
Hydril K-20-5000 Pulsation Dampener, Rod Cooling Pump, Bull Wheel,
Belt U-12 Detroit Diesel Engine W/Electric Starter Radiator,
Gauges Pump Drive Assembly, Master Skidded

1) National C-250 6X15 with Mattco Fluid End, powered by a
CAT 3406 Diesel Eng W/Electric Starter Radiator, Gauges Pump
Drive Assembly, Master Skidded

Gen Set:
1) 250 KW Light Plant powered by a 3306 CAT Diesel Engine
1) Ingersoll Rand Stand-by Air Compressor
1) Quincy Air Compressor
Top Dog House:
1) 17’W x 16’L Driller’s House w/Round Top, Knowledge Box,
Bench Storage, Parts Bins, (3) Lockers, Heater, Fluorescent Lights,
Skidded
1) Drillograph Single Pen Recorder

Fuel and Water:
1) 18’Dia. x 16’L Approx. 5000 Gal. Fuel Tank, Skidded
1) 14’3”H x 7’6 ½”W x 38’L 220 BBL Crimped Steel Water Tank, Skidded

Miscellaneous:
1) Set of BJ Type C Tongs
1) Set of 2 1/8” x 96” L Elevator Links
1) Web Wilson 150 Ton 4 ½” BN CL Drill Pipe Elevator

1) Lot of (1) 72”H and (1) 62”H x 28’ L Triangular Pipe Racks w/Catwalk Tray
1) 36”H x 7’5”W x 36’L Pipe Tub
1) 7’5”W x 34’L Drill Collar Skid

1) Assorted Rig Hoses, Piping and Stairways
1) 10” 3000 PSI Regan Annular

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Witchtex R-4 Trailer Mounted Drilling Rig for Sale
Trailer Mounted Land Drilling Rig for Sale
Witchtex R-4 Trailer Mounted Used Drilling Rig for Sale
Witchtex R-4  Drilling Rig for Sale in USA
---------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1430

Schramm TH130 Drilling Rig for Sale
750 hp Schramm TH130 Drilling Rig for Sale

Description :

Schramm TH130 -,760 hp deck engine, 28 inch (711 mm) table opening ,
1350/350 – 1150/500 variable volume compressor (38 cu. m/min
@ 24.1 bar & 32.6 cu m/min @ 35.5 bar), 50 feet (15.25 m) of clear
head travel, Capable of handling Range III casing

Mast : telescoping, 130,000 lbs. (59,090 kg) actual pullup

Back on Ramp 

Mud System : 12 x 50 pit with shale shaker

Mud Pump : D500 Emsco Duplex Pump
(2) 1150 HD x 350 Sullair Comp Hurricane Booster Trailer-Mounted
(2) 1150 HD x 350 Comp Hurricane Booster Trailer Mounted

WB12 Joy Booster

Doghouse, fuel tank, light plant, trailer mounted

Drill Pipe : 3500’, 4 ½” Range 2

Pipe & Collar Trailer

Rig can be set up with mud or air

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) - 
Schramm TH130 Drilling Rig for Sale
750hp Schramm TH130 Drilling Rig for Sale
Schramm Drilling Rig for Sale
Schramm TH130 Drilling Rig in USA
2003 Built Schramm Water Well Drilling Rig 
Used Schramm Drilling Rig for Sale
---------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2225

MD Cowan (Rig Tech RT 400B) Drilling Rig for Sale
750 Hp 2008 Built Drilling Rig for Sale

Description:

Rated 12000’
Built in 2008

Drawworks :  Rig Tech RT 400B, 750 HP, 500,000 lbs (8 lines), powered 
by (1) Caterpillar C18 750 HP

Derrick :  72’ one piece, 500,000# gross capacity

Substructure :  12’ MD Cowan

Rotary Table :  n/a

Top Drive :  Venture Tech XK 250 hydraulic power, 250 Ton

Iron Roughneck :  Bloom & Voss Floor Hand

Traveling Block :  Venture Tech 250 Ton

Floor Winches :  (2) Ram Hydraulic 5,000lbs, 10,000 lbs

Rig Power Plants :  (2) Caterpillar SR4, 455 KW, 1800 rpm, (2) Caterpillar C15’s

BOP:  (1) Townsend 11” 3000psi bag type preventer, (1) Townsend 
Double 11” 3000psi ram type preventer. 

Mud Pumps :  (2) Weatherford MP 10 powered by Caterpillar 3508C’s 1000 HP

Mud Tanks :  (1) 300bbl

Shale Shaker :  n/a

Hydraulic Catwalk :  MD Cowan Hydraulic Arm

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) - 
MD Cowan (Rig Tech RT 400B) Drilling Rig for Sale
750 Hp 2008 Built Drilling Rig for Sale
2008 Built MD Cowan (Rig Tech RT 400B) Drilling Rig for Sale
MD Cowan Used Drilling Rig for Sale
MD Cowan (Rig Tech RT 400B) Drilling Rig in USA
---------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1918

Superior 1000 Mechanical Drilling Rig for Sale
2006 Built Superior Drilling Rig for Sale

Description :

Drawworks:
Superior 1000M New (2006) Single Drum Drawworks, 1,000 Hp
Lebus grooved for 1-1/4” Drilling Line, Air operated Makeup
& Breakout Catheads, Over-Running Clutch, Air
Driller’s Console, Crown-O-Matic, Right Angle drive for rotary table.

Compound:
2-Engine, In-Line Compound, w/ Right Angle Drive RT
Box For rotary & Draw works drive

Brake:
PARMAC Dual V-80 Hydromatic Brake coupled together

Drawwworks Power:
No. 1 – CATERPILLAR C-18 Diesel Engine S/N# WJH01728,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N3444
 Air clutch
Hours# 21,597
 No. 2 – CATERPILLAR C-18 Diesel Engine S/N# WJH01706,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N1616
 Air clutch
Hours# 21,664

Mast:
DRILLMASTER New 2008 SN#07632 20’1 1”W x 136’H Cantilever Mast,
With a Gross Nominal Capacity of 930,000 Lbs. and a
650,000 Lb. Static Hook Load, Max wind 91 Knots,
 with ten (10) lines. Crown Block w/ (5)42” Sheave Cluster &
1-56”Fast line Sheave grooved for 1-1/4” diameter drilling line.
Each Crown Sheave wire rope groove is flame hardened.
Each Crown Sheave is fitted with Timken roller bearings and grease seals.
Derrick complete with Crown Safety Platform, 20 finger Racking Board W/ electric mule,
Bridal Lines, Tong Counter Weights, Survey Line Sheaves,
Tugger Sheaves, Ladder, Derrick Climber, Geronimo line,
4” Standpipe & Manifold and
Derrick Stand.
Last Certification 8/23/2012

Substructure:
DRILLMASTER New (2009) 29’10”W x 20’H x 48’8”L
(4) Box-On-Box Substructure w/ Rotary Beams, V-Door Ramp,
Stairs, (2) Air Receiver Tanks, NATIONAL Deadline Anchor,
Safety Rails, inside Catwalk Trolley, 7’W x 14’L built in Tool
Room (ODS) (3) Stairs, Outside wall Winterized, Jacking door,
12’ X 12’ Setback spreader, internal stairway, Vapor proof lighting,
Skidded with oilfield tail rolls

Pump: (Primary)
HT F-1000 Triplex Mud Pump New 2006,
S/N HT 20060088, 1,000Hp.
w/ LANZOU Pulsation Dampener S/N HT20060070,
MF 5,000 Psi. Pressure Gauge 
FIVE STAR 6”x8”x14” Charging Pump S/N5268 p/b TECO 75 Hp. Electric Motor,
 Chinese 3”Shear Relief Value, Master Skidded w/ (2) Engines belt compound

Pump Power:
CATERPILLAR C-18 Diesel Engine S/N WJHO1283,
575 HP w/24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours # 17,376
CATERPILLAR C-18 Diesel Engine S/N WJH01322,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON18CB500 Air Flex Clutch,
 Mounted Pump Master Skid
Hours#16,277

Pump (Secondary)
HT F-1 000 Triplex Mud Pump New 2006,
S/N HT 20060070, 1,000 Hp.
w/ LANZHOU Pulsation Dampener S/N HT20060069,
MF 5,000 Psi. Pressure Gauge
Five Star 6” x 8” x14” Charging Pump S/N5268 p/b Worldwide 75 Hp.
Electric motor,
3” Shear Relief Valve, Master Skidded w/ (2) Engine belt compound

Pump Power
CATERPILLAR C-18 Diesel Engine S/N WJH-00457,
575 HP w/ 24 volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted pump Master Skid.
Hours#13,788
CATERPILLAR C1-8 Diesel Engine S/N WJH-00373,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours#16,643

Rotating Equipment:
Rotary Table
Chinese ZP 27-1/2”, New 2006, complies with API split master bushings,
W/ drive shaft coupling.

Swivel
Ideco 300

Kelly
5-1/4” x 42’ Hex Kelly W/ HDS Kelly Drive Bushing

Kelly Spinner
OWI 1500 Kelly Spinner S/N 00475B w/ (2) Air Motors, New

Kelly Valves
Upper Kelly Valve.
Lower Kelly Valve

Travelling Equipment
Sentry Rig Equipment Company
260 Ton Capacity New 2006
4G260 Traveling Block w/ (5) 36” Sheaves, 1-1/4” Line,
Unitized “Hydra-Hook” 260 Ton Capacity

Blowout Preventer and Valves
1 Each -13-5/8" X 5000# Jiangsu Xianz hong Petroleum 
Double Gate BOP, Top & Bottom Stud configuration
Including - 1set of 5" Pipe Rams Blocks & 1set of Blind Rams,
With 2 - 4" outlets on each side of Body of BOP

1 Each - 13-5/8" Jiangsu Xianz hong Petroleum  ANNULAR BOP
Includes rubber element

1 Each - 13 5/8" X 5000# Type D Drilling Spool W/ - 2" Side Outlet & 3" Side Outlet
[Matched To Choke Manifold

1 Each - Choke Manifold - 3" X 5000# Complete
 Inc - Steel Flex Line W/ Flanges To Connect
To BOPS or Drilling Spools

Closing Unit
2008 Jiangsu Xianz hong Petroleum Model FXQ640-6
Closing Unit Accumulator, 6 Station,
 Rig Floor Controls and monitor panel,
Complete W/ 15 Bottles, 30 HP Cat 3517 Charge Pump, 21 Air Pumps, & set up
for Nitrogen Bottle Backup
Suitcase Closing Unit Skid 7’-1 0” x 35’ with junk basket

Choke Manifold and Valves
Jiangsu Xianz hong Petroleum Choke Manifold w/ (1) 5-Way Cross,
(3) 4-1/16”x 5M
Gate Valves, (4) 2-9/16” x 5M Gate Valves, (1) Manual
Adjustable Chokes, Hydraulic Adjustable Chokes, Mounted Oil Field Skid.
W/ 2 Kill Valves- & 2-Choke Valves mounted at drilling spool

Rig Houses:
Dog House, DRILLMASTER 9’ 1 1”W x 39’ 1 1”L
Doghouse / Change house Combination w/ 17’5”L
Driller’s House w/ Knowledge Box (5) Lockers, Bench Storage, Heater, Lights.
 5’L Breezeway, 1 7’5”L Change House, w/Bench Storage, (16-Lockers,
Cabinets, Heater & Lights. Oil Field Skidded

Generator/Utility Houses
DRILLMASTER 1 1’10”W x 37’9”L x 11’ 6” T
Utility House w/Lights, Oil Field Skidded to include the following items.

No #1 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01986 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0506, complete with Oil Field skid.
Hours# 17,278

No #2 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01985 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0507, complete with Oil Field skid.
Hours# 16,933

NO. 1 GARDNER-DENVER EBE99N New 2006
Electro Saver II Rotary Screw Air Compressor S/N# S237421,
P/b TOSHIBA 30 Hp. Electric Motor, Mounted 240 Gallon Horizontal Tank.
Hours# 15,128

SIEMENS Interlock Panel, 600 Amp 480 Volt Main Lockout Disconnects breakers.

ALLEN BRADLEY Electrical Load center with magnetic starter & breakers,

SQUARE D 225 amp 240 volt panel with breakers

SQUARE D 75KVA Transformer 480 volt to 240 volt

DRILLMASTER 7’9”W x 13”H x 43’1”L Electrical
Suitcase.

DRILLMASTER 2’5”W x 1 3”H x 36’3”L Electrical Suitcases.

Mud System:
DRILLMASTER 9’6”W x 7’H x 34’5”L, 394 Bbl. Suction Tank
10’L Covered Porch, (3) Compartments,
(3) MAX 2000 Mud Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Oil Field Skidded.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
With internal jetting system, 3 dump gates,

DRILLMASTER 9’6”W x 7’H x 34’7”L, 394 Bbl. Shaker Tank
10’L Covered Porch, (3) Compartments
MAX 2000 Mud Agitator Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Skidded.
With internal jetting system, 3 dump gates,

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5269,
p/b BALDOR 75 Hp. Electric Motor.

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5283,
p/b BALDOR 75 Hp. Electric Motor.

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N2450,

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N3089,

NOI DSN-ZH-10CTX Desander S/N 8714-5732,w/ (2) 10” Cones.

NOI DSL-10GG-4CTX Desilter S/N 8714-5731,w/ (10)4” Cones.

DRILCO “Deep Pit” Degasser p/b TECO 10 Hp. Electric Motor

Bubble Buster: Geothermal Type Bubble Buster

Mud House
DRILLMASTER 9’ 1 1”W x 26’L Mud House w/Mud Hopper, Test Sink,
Ventilation Fan, Electric Heater, Lights, Double Side Door, (2) End Doors, Skidded. 
Includes 7’H Tri-Stand on one end the other end sets on suction tank.

Fuel Tank
DRILLMASTER 7’1 1”Wx8’Hx30’L, 13,860 Gallon Fuel Tank
w/ (2) AMT 1/2 Hp. Fuel Transfer Pumps p/b BALDOR 1/2 Hp. Electric Motors,
with Three (3)Compartment, Combo Lubester Oilfield Skidded.

Water Tank
DRILLMASTER 10’10”W x 8’1”H x 35’L, 529 Bbl. Water Tank
w/ 10’L Covered Extension, Pump Room, OilField Skidded
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N 5420, p/b TECO 20 Hp. Electric Motor.
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N5267, p/b TECO 20 Hp. Electric Motor.

Instrumentation
Weight Indicator
Mud Gauges.

Ancillary Equipment
DRILLMASTER 5’W x 2’4”H x 60’L, 2-Section Catwalk w/ Steel Deck and stands for string blocks.
Pipe Racks 5 Sets 29” x 30’ 1 set 29” x 12’ 1 set 41” x 30’
FIVE STAR “Retriever” Electric Measuring Device S/N 862, w/ 15,000 Ft. of. 092 Wire line
2 sets drill pipe elevators 5”
2 sets of drill pipe slips 5”
2 sets of drill collar slips 7” & 9”
2 sets tongs with all head for pipe & casing
2 sets of safety clamps
Mud box  with 5” rubbers
108” X 4” elevator bails
Crossover, bottom hole, lifting Subs
Air Hoist Air Wrench, Model HUL40, S/N-REM10370, 9000 lb. Pull Rating
Air Hoist Air Wrench, Model KSUL, S/N-REM13962, 10,500 lb. Pull Rating
4,000 Ft. of 1-1/4” Drill Line, Mounted Spooler Stand
3-1/2” X 5,000 Psi. Rotary Hose
Vibrator Hose 2 Each 3 ½” x 18’
Rat hole
Mouse hole
8 rig matting boards
Small hand tools & wrenches
Fluorescent & Mercury-Vapor Rig Lights & Wiring Explosion proof
Atco Office/ living shack all electric w/ oil field skid

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) - 
Superior 1000 Mechanical Drilling Rig for Sale
2006 Built Superior Drilling Rig for Sale
1000hp Superior Drilling Rig for Sale
Superior 1000 M Drilling Rig for Sale in USA
Mechanical Drilling Rig for Sale in USA
---------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1012

Ingersoll-Rand RD20 Range II Drilling Rig For Sale
Used Drilling Rig 1996 Built

Model : RD20 II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1996
Condition : Used

Description
1996 Ingersoll-Rand RD20 Range II Drill Rig
CAT 3406 Diesel Deck Engine
Bean Water Injection Pump
7 Rod Carousel
3 Hydraulic Leveling Jacks
110,000 lbs of Pullback
Mounted on a Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
Note: Bill of Sale only, no title
Note: No Air Compressor on board

Location : USA

Price & terms : Please enquire using the email form below. 

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search Words(for official use only) :
Ingersoll-Rand RD20 Range II Drilling Rig for Sale in USA
Used Drilling Rig For Sale
Drilling Rig Ingersoll-Rand RD20 Range II - 1996 Built For Sale
Ingersoll-Rand RD20 Range II Drilling Rig for Sale in USA
1996 Ingersoll-Rand RD20 Range II Drilling Rig
Land Drilling Rig Ingersoll-Rand for Sale
-----------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1446

MAC Mechanical Drilling Rig for Sale
450 hp Drilling Rig for Sale in USA

Description

Drawworks : 
Mac 400 with hydromatic (water) brake, catheads, powered by a Caterpillar 3408 rated
at 450 HP with air clutch and torque converter

Mast : 
P-J Services, 98’ free standing derrick, 280,000#, angle iron steel beams, scopes
with king pin and two axle dolly. Racking capacity of 8500’ of 4 ½” drill pipe

Substructure : 
One piece, I beam box type. 8’H x 15’W x 34’L with 4’ fold down wings, enclosed parts house
and large volume tank with Quincy 350 air compressor driven by electric motor in substructure.

Rotary Table : 
Brewster 17 ½”, rotary bushing-square, 4 ½” square Kelly

Block/Hook : 
Three sheaves (6 lines) grooved for 1 1/8” line

Swivel : 
TSM 150 ton with new wash pipe and packing

Generator : 
125 KW powered by Detroit 6-71 in steel house with all switchgear and transformer. 
Steel house includes parts cabinets, work area, and storage

Mud Pump :
Gardner Denver FXN 7 ½” x 14’ duplex powered by a Cat 3408 (450 HP) with air clutch

Mud System : 
Single cone desander, Mission Magnum mud mixing pump, mud stirring guns 
(rig uses earthen pits)

BOP : 
Regan 10” annular (new annular rubber)

Top Dog House : 
Scopes down into 400 barrel water tank, heater lockers, knowledge box

Drill String : 
200 joints 4 ½” x-hole, 16.60 ppf drill pipe, yellow band, 12 assorted subs,
lower Kelly valve, inside BOP

Ancillary Equipment : 
Kelly hose (new), vibrator hoses (3), 2500’ of 1 1/8” drill line (new), mouse hole, mouse
hole driller, weight indicator, tong torque gage, bear automatic driller, one pen drill recorder,
Sure Shot deviation instrument, mud gages, (3) sets pipe racks, Type C rotary tongs, rig lights
(derrick, sub, mud pump, gen house), drill collar slips, (2) sets drill pipe slips, Quincy 325
air compressor with electric motor, slick line wire line unit mounted on single axle trailer.  

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only)
Mechanical Drilling Rig for Sale in USA
MAC 400 Drilling Rig for Sale in USA
8500 Drilling Capacity Land Rig in USA
Mechanical Drill Rig 400hp for Sale
MAC - 8500 Drilling Capacity Oil Rig for Sale
450hp Land Drilling Rig for Sale
----------------------------------------------------------------------------------------------

Worldrigs ID: WR191

U-36 AE Diesel Electric Rig for Sale
700hp Diesel Electric Rig for Sale
U-36 AE Diesel Electric Rig - 700hp

Specifications
Drawworks :
Mid-Continent U-36 AE Diesel Electric 700hp, S/D drawworks, Lebus
grooved F/1-1/8” line, air drillers console, 22” hydromatic brake, hyd.
Tank with hyd. pump P/B 2hp electric motor, P/B GE 752 traction
motor, with blower, 1000hp, all mounted covered skid with fluorescent
lights, ruffneck heater, master skidded.

Mast :
Parco 131’H x 178’8” W Cantilever mast, 360,000# SHL, pin-type,
crown block, with (5) 36” sheaves, 46” fastline sheave, 1-1/8” line,
4” standpipe, crown safety platform, racking board, tong counter
weights, ladder derrick climber, mast stand, fluorescent lights.

Sub:
Parco 22’H x 25’W x 35’L self-elevating substructure, self-skidded,
rotary beams, stairs, safety rails, deadline anchor, skidded with
V-door, 42”H x 5’W x 32’L, 2-section catwalk with steel deck.

Top Drillers House :
10' H X 8' W X 20' L RD top doghouse with 3’L porch, knowledge box,
lockers, lights, bench and cabinet storage, remote closing unit, skidded.

SCR House :
Baylor model SE-33-BA-301, 3-Bay SCR drive system, S/N 1001-61054,
600 VAC, 60HZ input, multiple controlled DC outputs AT0-750 VDC, Allen
Bradley switch gear & Baylor instrumentation, (2) Marcus transformers,
(1) 600-400 volts, (1) 460-208 volts, MTD IN 10’H x 10’6”W x 20’L house,
Lennox T-Class heat/air unit, emergency lights, skidded.

Generator :
Caterpillar 600KW generator P/B CAT 3412 diesel engine, S/N 81Z0127,
electric start, radiator, gauges, skidded BBC 715 700KW generator set,
P/B CAT 3412 880hp diesel engine S/N S/N 38S2V356, air start, radiator,
gauges, skidded. All above MTD IN 10’W x 36’L generator house,
fluorescent lights, day tank, skidded.

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.



-----------------------------------------------------------------------------------
Search words(for official use only) :
U-36 AE Diesel Electric Rig - 700hp for Sale
700hp Diesel Electric Rig - U-36 AE for Sale
U-36 AE Diesel Electric Rig
Land Rig for Sale
Diesel Electric Rig - 700hp - for Sale
-------------------------------------------------------------------------------------

Worldrigs ID: WR214

Worldrigs ID: WR268

Speedstar 275 Quickdrill Drilling Rig For Sale
Used Drilling Rig 1986 Built for Sale

Model : 275 Quickdrill Rig
Manufacturer : Speedstar
Year : 1986
Condition : Used

Description :

1986 Speedstar 275 Quickdrill Rig
4X3X13 Centrifugal Mud Pump
Leroi compressor 50SDS (rebuilt in 2000)
Main Winch & Sandline
Single Rod Loader
Rod Rack
(16) 2-3/8" IF x 15' ft drill pipe and 6" inch stabilizer
Mud pan and suction line
4 hydraulic leveling jacks
Mounted on a newer 1992 GMC Topkick Truck
CAT Diesel Engine
10 Speed Transmission
4 newer rear tires
203000 miles

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
 
--------------------------------------------------------------------------------------
Search words(for official use only) -
Speedstar 275 Quickdrill Rig for sale
Drilling Rig - Speedstar 275 Quickdrill
Used Drilling Rig for sale
Speedstar 275 Quickdrill Drilling Rig for Sale in USA
1986 Built Speedstar 275 Quickdrill
------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR488

Drilling Rig - Speedstar SS-15 II For Sale
Speedstar SS-15 II Drilling Rig 1977 Built for sale

Model : SS-15 Drill Rig
Manufacturer : Speedstar
Year : 1977
Condition : Used

Description :
1977 Speedstar SS-15 II Drill Rig
Mounted on a 1977 GMC Truck
13 Speed transmission
Rig Serial #: 7154
4 1/4" Kelly
18 GPM John Bean water injection system
Double Drum Drawworks with air clutches
Sandreel
Table Drive
750 cfm / 300 psi Sullair air compressor/low hours installed prior to purchase in 2002
C60 Engine, Easy start, runs great, burns no oil
Table Drive, 8 1/2" opening, hydrostatically driven
Air Controls
Easy load, Rod tray with 17 pieces of 3-1/2" API x 4-1/2" OD x 20' Rods (340') 
in rack + 25 foot Kelly Bar/365' ft total

Line oiler, electric/air
4 hydraulic leveling Jacks
35' mast height above table
Safety Shut Down
Machine runs exceptionally well
6" Bit basket
10" Bit basket
Pipe rollers
Drill Rod Clamps
Chain Wrench
260' ft of additional drill rod available at an extra cost 

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.



---------------------------------------------------------------------------------------------------------------------------------
Search words(for official use only) -
Speedstar SS-15 II Drilling Rig For Sale
Drilling Rig Speedstar SS-15 II 1977 Built for sale
Used Drilling Rig Speedstar SS-15 II for sale
Used Speedstar SS-15 II Drilling Rig for sale in USA
Land Drilling Rig For Sale
1977 Built Speedstar SS-15 II Drilling Rig for sale
-----------------------------------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1910

Crown Duke CE 750 SD Drill Rig for Sale
2008 Built Crown Duke Drill Rig for Sale

Model No : CE 750 SD Drill Rig
Manufacturer : Crown Duke
Model Year : 2008
Condition : Used

Description

2008 Crown Duke CE 750 SD Drill Rig
powered by a Detroit Series 60 14 Liter Diesel Engines
Allison 6610 Automatic Transmission.
118′ x 350,000 Lb Capacity Double Telescoping Mast
630 BBL Twin Tank Mud System
27 1/2″ Salem & FDS Rotary Table
(2) 1000 HP Triplex Mud Pumps

450 kW Generator House
Skidded Drive-On Platform
Keep reading for more detailed information.
Draw Works: Single Drum
Engine Specs: Detroit Series 60 14 Liter Diesel
Est. Max Depth: 10,000 ft
Fuel Type: Diesel
Horsepower: 665
Mast or Derrick: 118 ft x 350,000 Lb Capacity, Double Telescoping
Mounted On: Carrier
LISTED SEPARATELY: Mud Pumps (2) 1000 HP Triplex Pumps,
P/B CAT 3508 1000 HP
Rotary Table: 27 1/2" Salem & FDS

Title: Yes
Transmission: Allison 6610 Automatic Transmission
VIN: 1C9ST184982978004
630 BBL Twin Tank Mud System
(1) Generator House; 450 KW Generator, P/b Detroit Series 60 14 Liter Diesel Engine
(1) Hydraulic Raised Substructure; 14 " High x 10' Wide x 18' Long
(1) Top Doghouse with Storage and Hand Tools
(1) Bottom House with Lockers, Lubester, and Circulating Pumps
(1) Fuel Tank - 8,000 Gallon Capacity with Pump, Double-walled
(1) Water Tank - 300 BBL Capacity with Wash Pump, Mud Line, Valves and Manifold
(1) Center Wall - 54′ Long
(1) Skid with Suitcase and Ladders
(1) Skid with Junk Box, Rotary Tongs, and Rathole Diggers
(1) Pipe Tub with Blow Line and Pipe Racks
(1) National 175 Ton Block Hook
Various Matting Boards for Rig Support
Rotary Hose and Drill Line
Mounted on 6 Axle Carrier
v-Door and Cat Walk
8,000 Gallon Fuel Tank

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------
Search words (for official use only) -
Crown Duke CE 750 SD Drill Rig for Sale
2008 Built Crown Duke Drill Rig for Sale
Used Drilling Rig for Sale in USA
Crown Duke CE 750 SD Used Drill Rig for Sale
Used Drill Rig - 2008 Built - for Sale
Crown Duke CE 750 SD Drill Rig for Sale in USA
--------------------------------------------------------------------------------------------

Worldrigs ID: WR1449

Mobile B80 Drill Rig for Sale
1991 built Used Mobile B80 Drill Rig for Sale

Model : B80 Drill Rig
Manufacturer : Mobile
Year : 1991
Condition : Used

Description :

1991 Mobile B80 Drill Rig
Mounted on 1992 Ford LT-9000 Truck 6x4
Rebuilt CAT 3406B Diesel Engine
23,000 Miles
SAFE-T-DRIVER
Main & Auxiliary hoist
Sullair 750 cfm / 150 psi Screw Air Compressor
PTO with 3 stage hydraulic pump
breakout wrench
2” NPT air/water swivel
front & rear stabilizer jacks
Moyno 3L4 water pump 225 psi/17 gpm Tarby water pump (Both pumps need work)
Tooling also included:                               
105’' of (4-1/2 x 15')’ Reg pin x box drill rods with flats
6"”, 8"” and 10"” bits
Hammer
140 lb slide hammer
70’ 1-¾”" AWJ rod
(2) AWJ 2” x 24” split spoon samplers

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

----------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Mobile B80 Drill Rig for Sale
1991 built Used Mobile B80 Drill Rig for Sale
Used Drilling Rig for sale
Mobile B80 Drill Rig 1991 Built for sale
Mobile Drilling Rig for sale
----------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2456

Speedstar SS-22 - Cummins Powered Drill Rig for Sale
1976 Built Speedstar SS-22 Drill Rig for Sale

Description :

1976 Speedstar SS-22 - Cummins Powered
Double Drum Drawworks 100,000 Hook load USA

1976 Speedstar SS-22-SN: 30268 is a three-axel carrier mounted drill rig
having a side-by-side double drum draw works. Each drum is rated at
18,000# SLP. Owner reports the mast is appox. 50' tall with a 100,000# hook load.

Rig mounted on a crane carrier chassis with Cummins motor

2" Speedstar swivel

8.5" Speedstar rotary table

256 Leroi air compressor

Driller's platform, and derrick board.

Gardner Denver 5-1/2 x 8 mud pump, 3" water course

Shop built 20' gooseneck pipe trailer with pipe slide.

Shop built 20' gooseneck tool house trailer with insulted dry van box

Drill pipe:- 800 ft. of used drill pipe, consisting of:
1.) 500 ft. of used drill pipe (2-3/8" tool joints);
2.) 300 ft. of 2-7/8" bottleneck drill pipe (2 3/8" tool joints).

Tooling : drill pipe slip; drill pipe hoist plug and sling;

8-5/8" casing swedge; 4-1/2" casing swedge;

(2) 4-1/2" elevators; bit subs;

11.0" PDC bit.

6.75" PDC bit

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us anemail to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------
Search Words (for official use only) :
Speedstar SS-22 - Cummins Powered Drill Rig for Sale
1976 Built Speedstar SS-22 Drill Rig for Sale
Speedstar Land Drilling Rig in USA
Used Speedstar SS-22 Drill rig
Speedstar Cummins Powered Used Drill Rig in USA
---------------------------------------------------------------------------------------------------

 

Worldrigs ID: WR1389

Schramm T64HB Drill Rig For Sale
Schramm Used Land Drilling Rig For Sale in USA

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig - Serial Number: T64HB-1313
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on a GMC truck - VIN TJV738V578079
diesel engine

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Schramm T64HB Drill Rig for Sale in USA
Schramm Land Drilling Rig
Used Schramm T64HB Drill Rig
Schramm T64HB Used Drill Rig for Sale
Schramm T64HB Drill Rig For Sale
---------------------------------------------------------------------------------------------------------

 

Worldrigs ID: WR1390

Used Drilling Rig for Sale
CME 75 Drill Rig for Sale in USA

Model : 75 Drill Rig
Manufacturer : CME Drill
Condition : Used

Description :

CME 75 Drill Rig
Diesel Deck Engine
Hydraulic Leveling Jacks
Mounted on a Ford Truck
Diesel Engine

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

------------------------------------------------------------------------------------------------
Search words(for official use only)
CME 75 Drill Rig for sale
Used Drilling Rig for Sale
CME 75 Used Drill Rig
Land Drill Rig - CME 75
Used Drilling Rig for Sale in USA
--------------------------------------------------------------------------------------------

Worldrigs ID: WR154

Wilson Mogul 42 Double Trailer Mounted Rig for Sale
550 HP Mechanical Drilling Rig Trailer Mounted

Description :

Wilson Mogul 42 Double Trailer Mounted Rig
550 HP, Mechanical, +/- 6,000' Trailer Mounted Drilling Rig
Country: USA

Draw Works:
- Single Drum Draw Works
- Foster Model 27 AH break out Cat heads (serial # 1404)
- Manual Braking System
- 1,500’ 1” drilling line, spooled, never used, still in protective coating
- Driller’s console, with controls

Power:
- Detroit Model 12V71 diesel engine
- Engine rated for 550 peak Horse Power
- Radiator and Electric starter
- Allison Model TC955 torque converter

Substructure:
- 10’ Height
- 16’ Width (with walkways extended)
- 12’ Length
- 2 piece substructure
- Box type structure, with rotary table beams
- 10’ W x 40’L back on ramp
- Removable Stairways
- Folding walkways
- Safety railings
- Lighting
- Includes rat hole / mouse hole digger

Mast:
- Wilson 102’ Height hydraulic derrick (serial #991-102-300)
- Hydraulically raised with multiple scooping raising arm
- Crown Block and Safety Platform
- Pipe racking board
- Standpipe
- 3” (ID) x 50’ long Kelly hose
- Tong counterweights
- Vapor proof lighting
- Martin – Decker weight indicator

Rig Mounted Equipment:
- Hydraulic Break Out Cylinder
- Winch
- Hydraulic Storage Tanks
- Fuel tanks
- Air compressor – Bendix Westinghouse Model TUFLO 1000
- Deadline anchor
- Hydraulic leveling jacks
- Folding walkways, with stairs and safety railings
- Rig Mounted on Tri Axle Trailer

Travelling and Rotating Equipment:
- Chain Driven Rotary Table - Gardner Denver Model 175
- Split Master Bushing
- Swivel - Gardner Denver Model SW 125
- Kelly - Brand New 40’Length x 4 1/4” Square Kelly
- Drive Bushing
- Travelling Blocks - 3 sheave blocks, grooved for 1” line
- WEBB-WILSON Hydra Hook Elevator Bales
- Rig set up to add an extra travelling block to increase all capacities
- Air Head Oiler

Casing, Pipe and Equipment:
- 7,000’ +/- 3 ½ OD drill pipe
- 3 ½ ” IF connection
- 4 ¾ ” OD flush drill collars, 3 ½” IF connections, slip recessed
- 6 ¼ ” OD with 4 ½ “ X-hole connection drill collars
- 2 Standard 32’ pipe trailers
- 1 Extended 35’ center trailer

Well Control Equipment:
- Williams 11” annular BOP
- Washington Rotating head assembly, complete with 16 ¾” air bowl
- Assortment of Flanges including
- Companion flange 13 5/8 x 13 3/8
- Companion flange 13 5/8 x 9 5/8
- Companion flange 13 5/8 x 7 inch

Custom Rig Doghouse:
- 8’W x 24’L trailer mounted dog house
- Easy Access Front Porch
- Rear porch where generator is mounted
- Custom Built House for all tools
- Storage areas
- Breezeway
- 3000 gal fuel cell
- Geolograph
- Work Bench
- Drilling Supplies
- Night work lights
- All mounted on 40’ trailer

Generator:
- Stateline 10 KV generator with all necessary Switching gear, gauges and controls, mounted on Rig Doghouse Porch
Miscellaneous Equipment and Parts:
- Tool Trailer
- Soap tank with MYERS Model C20-8CR injection pump and 1 ¼ “ lubricator
- Soap pump powered by Waukesha Engine
- Assortment of casing elevators and single side door elevators
- 2” air pump
- Assortment of change over subs
- Dead man stakes and cable for rig tie down and secure lines
- Webb Wilson Type B tongs with assortment of tong jaws
- 4 ½ “ bottleneck drill pipe elevators
- Drill collar slips

Air System (available at additional cost):
2001 Ingersoll Rand Airpac:
- Model number XHP1170
- Twin air compressors included
- Trailer Mounted
- Cat powered C15 engines capable of 525 HP
- Twin air units rated for 350 PSI and 1170 Cubic Feet each
- Both air unit have approx 7,600 hrs
- All units plumbed together
- compressor, complete with all necessary collers, gauges, valving and controls

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

-------------------------------------------------------------------------------------------
Search words (for official use only) :
Wilson Mogul 42 Mechanical Drilling Rig for Sale
Mechanical Drilling Rig for Sale
550 HP Wilson Mogul 42 Double Trailer Mounted Rig 
Wilson Mogul 42 Drilling Rig for Sale in USA
Trailer Mounted Mechanical Drilling Rig for Sale
-------------------------------------------------------------------------------------------

Worldrigs ID: WR1422

Reichdrill 650 Drill Rig For Sale
Drilling Rig Reichdrill 650 for Sale

Model : 650 Drill Rig
Manufacturer : Reichdrill
Year : 1989
Condition : Used

Description : 

1989 Reichdrill 650 Drill Rig
CAT 3406B Diesel Deck Engine (10,500 hours)
Air Compressor
Mounted on an International truck
Cummins 350 Diesel Engine
18 speed transmission
103,788 miles on it
20,000 lb front end and the rear end is 46,000 lb
two piston Bean water injection pump
hammer oil lubricator
500' ft of 4.5'' rods with 3.5'' API threads (in good shape)
rotary head can accommodate two motors

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Reichdrill 650 Drill Rig For Sale
Drilling Rig Reichdrill 650 for sale
Land Drilling Rig For Sale in USA
Reichdrill 650 Used Drill Rig For Sale
1989 Built Reichdrill 650 Drilling Rig for sale
----------------------------------------------------------------------------------------------------------

Worldrigs ID: WR601

Williams LLDH Used Drilling Rig for Sale
Foundation / Caisson Drilling Rigs

Model : LLDH
Manufacturer : Williams
Year : N/A
Condition : Used

Description
Capable of drilling 80' ft deep and 60-72" inches in diameter
It has been reconditioned in 2002
Very good working condition
Located in Europe

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

------------------------------------------------------------------------------------
Search words (for official use only) -
Williams LLDH Drilling Rig for Sale
Used Drilling Rig Williams LLDH  for Sale
Oilfield Drilling Rig for Sale in Europe
Foundation Drilling Rig - Williams LLDH
Williams Drilling Rig for Sale in Europe
Foundation / Caisson Drilling Rigs for Sale
Williams Used Oilfield Drilling Rig for Sale
----------------------------------------------------------------------------------

Worldrigs ID: WR2205

1985 Built Wilson Mogul - Refurbished in 2006 - For Sale
Used Workover Rig for Sale

General
Built : 1985
Full refurbished : 2006

Specifications
Engine: P/B Detroit Series 60 Diesel Engine
Transmission: Allison 5861
Brake: PARMAC 122 Hydraulic Brake C/W Water Tank 300 Gallon

Mast Specifications
Wilson Telescoping Equipped with Rod & Tubing  Boards, Hydraulic Leveling
Jack, Utility Winch, Mounted on Truck 5 Axles Carrier  And Work Platform.
Heights : 96’Capacity: 251,000 LBS
Raveling Block : MCKISSICK83A 100 Ton , c/w (3) 24” Shaves  f/1” Line
1” Tubing Line
Duplex Hook
Tire is new

Condition is very good

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
----------------------------------------------------------------------------------------------------------------------------------------
Search words(for official use only) -
Wilson Mogul 42B Mounted Truck Well Service Rig
1985 Built Wilson Mogul - Refurbished in 2006 - For Sale
Land Drilling Rig for Sale
Refurbished Wilson Mogul 42B Mounted Truck Well Service Rig for sale
Wilson Mogul Workover Rig for Sale
Used Workover Rig for Sale
-----------------------------------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1452

DeepRock DR-150 Drill Rig for Sale
Used 2003 Built DeepRock DR-150 Drill Rig

Model : DR-150 Drill Rig
Manufacturer : DeepRock
Model Year : 2003
Condition : Used

Description :

2003 DeepRock DR-150 Drill Rig
American Manufacture 5x6 Duplex Mud Pump
Winch
Bean 10 GPM Water injection
Hammer lubricator
Sliding head
Power Head (0 hours since rebuilt)
4 hydraulic leveling Jacks
No pipe
Mounted on a 2003 Ford F750 4X4
Cummins 5.9 engine
VIN# 3FDXF75X03MB03833

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

------------------------------------------------------------------------------------------------------------
Search words(for official use only) :
DeepRock DR-150 Drill Rig for Sale
Used DeepRock DR-150 Drilling Rigs for Sale
DeepRock Drill Rig Land Drill Rig for Sale
DeepRock DR-150 Used Drill Rig for Sale
2003 Built Used Drilling Rig
--------------------------------------------------------------------------------------------------------------

 

 

Worldrigs ID: WR826

Canterra CT 250 Drill Rig for Sale
Drilling Rig Canterra CT 250 for Sale

Model : CT 250 Drill Rig
Manufacturer : Canterra
Condition : Used
Year : 1991

Description :

1991 Canterra CT 250 Drill Rig
4x5 Mud Pump
160' ft. of 2-3/8” Mayhew Jr. included
Auger Bit
Mounted on 1991 International 4700 truck
Diesel Engine
 
Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Canterra CT 250 Drill Rig for Sale
1991 Built Drilling Rig for sale
Canterra CT 250 Used Drilling Rig
Canterra CT 250 Drill Rig for Sale in USA
Canterra Land Drilling Rig For Sale
-------------------------------------------------------------------------------------

Worldrigs ID: WR790

Acker Soilmax Crawler Drill Rig for sale
Used Drilling Rig for sale

Model : Soilmax Crawler Drill Rig
Manufacturer : Acker
Condition : Used

Description :

Acker Soilmax Drill Rig
Mounted on a Marooka MST 1500 Crawler Carrier
Hours on Marooka 5,895
Hours on Soilmax approx 500
Also has a removable Hydraulic Chuck, Breakout Wrench, and Table
Table needs to be hooked up to hydraulics
Location : USA

Price & terms : Please enquire using the email form below.   

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

-------------------------------------------------------------------------------------------------
Search words (for official use only) :
Acker Soilmax Crawler Drill Rig for Sale
Used Acker Soilmax Drill Rig
Land Drilling Rig For Sale
Used Acker Soilmax Drill Rig for Sale
Soilmax Crawler Drilling Rig for sale  in USA
------------------------------------------------------------------------------------------------

Worldrigs ID: WR567

Walker Neer C33-A Triple Drum Service Rig for Sale
1978 Built Triple Drum Service Rig for Sale in USA

Model : C33-A Triple Drum Service Rig
Manufacturer : Walker Neer
Year : 1978
Condition : Used

Description :

1978 Walker Neer C33-A Triple Drum Service Rig
Right angle drive
cable raise and telescope 65' double pole mast
spud beam
auxiliary 8000 lb hydraulic winch
air clutch
cat head
spooling device and sheave
cab protector
auxiliary hydraulic tong circuit
2 hydraulic outriggers
2 sheave traveling block
weight indicator
Mounted on a 1978 International F-2574
Tandem axle truck chassis VIN #CF257HHA20526
With Cummins 300 Diesel
Fuller 6 speed transmission
Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------
Search words(for official use only) -
Walker Neer C33-A Triple Drum Service Rig for Sale
Triple Drum Service Rig for Sale in USA
Walker Neer Drilling Rig for sale in USA
Used Walker Neer C33-A Triple Drum Service Rig
Walker Neer Used Drilling Rig for sale in USA
------------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1413

CME 75 Drill Rig for Sale
CME 75 Used Drill Rig - 1987 Built

Model : CME 75 Drill Rig
Manufacturer : CME Drill
Year : 1987
Condition : Used

Description :

1987 CME 75 Drill Rig
Has 3L6 Moyno Pump
Cat Head
2 Winches
4 Cylinder Gas Engine
The Rig Runs Good
Mounted on a 1988 Ford 750 Tandem Axle (Note: truck is in poor condition).
Also a brand new Auto Hammer in box that can be fitted on the drill

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words (for official use only) :
CME 75 Drill Rig For Sale
Used Drilling Rig CME 75 for sale
Drilling Rig CME 75 For Sale in USA
CME 75 Drilling Rig 1987 Built for sale
Land Drilling Rig For Sale 1987 Built in USA
----------------------------------------------------------------------------------------------------------

 

Worldrigs ID: WR1127

Schramm T64HB Drill Rig For Sale
Used Drilling Rig  for Sale

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on Ford Truck

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

 ---------------------------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Schramm T64HB Drill Rig For Sale
Used Drilling Rig  for Sale
Schramm Used Drilling Rig 
Land Drilling Rig For Sale in USA
Schramm Drilling Rig for Sale
Schramm T64HB Drill Rig For Sale in USA
-----------------------------------------------------------------------------------------------------

Worldrigs ID: WR2091

Gardner Denver 700 Drilling Rig 
800 hp Mechanical Drilling Rig for Sale

Description :

Gardner Denver 700 Drilling Rig
800 HP, Mechanical, Box on Box 
14,000’ Capacity with 4 ½” Drill Pipe

Drawworks:
Gardner Denver 700 with 342 Parmac Hydromatic Brake powered by (2) Cat C-15
engines with (2) National 195-80 torque converters – 800 HP

Substructure & Mast:
Pyramid 131’ mast, 550,000 GNC, 1 ¼” line
Pyramid 20’H substructure

Generators:
(2) 320 KW AC Generators powered by (2) Cat C-15 diesel engines

Mud Pumps:
(2) Gardner Denver PZ-9, driven by (2) 3508 Cat Diesel motors

Rotating & Traveling Equipment:
Chinese Rotary Table – 27 ½”
Emsco Block and BJ Hook – 250 Ton
Ideco Swivel – 300 Ton
5 ¼” x 42’ Kelly Varco HD Pin Drive Bushings

Blowout Prevention:
13 5/8” annular BOP – 10000 psi
13 5/8” double gate ram BOP – 10000 psi
13 5/8” single
4” x 3” – 10000 psi complete manifold with gauges and chokes

Doghouse, Water, Fuel & Mud Tanks:
Heated Doghouse
(1) Fuel tank – 12,000 Gal
(1) Water Tank – 500 Bbl
(2) 10’ x 5’ x 40’ mud tanks complete with (4) 5” x 6” electrical driven centrifugal
pumps manifold to low pressure mud system with electrically driven mud
agitators, mud guns – 650 Bbl capacity
(2)Fluid System linear shale shakers, (1) Fluid System desander 10” cones, (1) Fluid
System Desander 2 cones, (1) Fluid System desilter 10 – 4” cones

Handling Tools/Auxiliary Equipment:
BJ 48” Type B tongs
Pilot II Automatic Driller
Sure Shot 14” A-1 Survey Instrument
MD Totco Type D Weight Indicator

Drill Pipe & Collars:
300+ Jts. 4 ½”, 16.6# drill pipe
(3) 8” x 30’ drill collars
(22) 6 ¼” x 30’ drill collars

Rig Manager’s Camp

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Gardner Denver 700 Land Drilling Rig for Sale
800hp Mechanical Drilling Rig in USA
Mechanical Drilling Rig for Sale
Land Drilling Rig - Gardner Denver 700 - for Sale
Gardner Denver 700 Mechanical Drilling Rig 
---------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR392

Drilling Rig - Ballerini ST4 - for Sale
Ballerini ST4 Drilling Rig for Sale
Used Drilling Rig for Sale in Europe

Model : ST4
Manufacturer : Ballerini
Year : N/A
Condition : Used

Description :

Ballerini ST4 drill rig (similar to the Failing 2500 drill rig)
Rated for 3,600’ ft (1,100m) depth, casing loads to 66000 lbs. (30,000 kg)
Telescopic type mast with 58’ ft working space
Drilling Line Spooling Capacity 1400’ ft
Sand Line Spooling Capacity 3600;
2 Catheads mounted on sand line drum shaft, 8-5/8”
18” Rotary Table
Engine power on board model VM 80HP
Mud Pump Model Ballerini 5-1/2 x 8
Winches max shooting 20Ton.
Ballerini 5"x 6" Mud Pump
180 HP Deck Engine
1 Kelly 7,50 mt
Trailer Mounted
Hours of work : 23.000 H
Location : Europe

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.



---------------------------------------------------------------------------------------------------
Search words(for official use only) :
Used Ballerini ST4 Drilling rig for Sale
Ballerini ST4 Drilling Rig for Sale
Used Drilling Rig - Ballerini ST4
Drilling Rig for Sale 
Land Drilling Rig for Sale
Used Drill Rig for Sale
---------------------------------------------------------------------------------------------------

 

Worldrigs ID: WR822

Ingersoll-Rand T4W Drill Rig for Sale
1994 Built  Ingersoll-Rand T4W Drill Rig

Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used

Description

1994 Ingersoll-Rand T4W Drill Rig
Cummins KTA19C Diesel Deck Engine
IR 1050 cfm / 350 psi Air Compressor
Worm Gear Power Head
4 & 7 Rod Carousels
14,570 hours
Water Injection Pump
Hammer Lubricator
50,000 lbs of Pullback

Included as a package:
2000' ft of (4.5" x 25') drill pipe, 6" & 8" & 10" drill collars,
used 6" & 8" Hammers & Bits, Handling Plates,
Breakout Wrenches, Petal Tongs

Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
21,830 Miles

Location : USA

Price & terms : Please enquire using the email form below.   

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Ingersoll-Rand Drilling Rig for Sale
Used Ingersoll-Rand T4W Drilling Rig for Sale
Drilling Rig for Sale in USA
1994 Built Ingersoll-Rand T4W Drilling Rig
Used Drilling Rig - Ingersoll-Rand - in USA
---------------------------------------------------------------------------------------------------------

Worldrigs ID: WR1962

Wilson 65 Mechanical Drilling Rig for Sale
Mechanical Drilling Rig for Sale

Drawworks:
Refurbished Wilson 65 drawworks with a refurbished twin engine compound 
powered by two (2) 3406 CAT engines, re-built 500 hours, totaling 870 hp. 
Allison torque converters with air clutches (new).

Derrick:
105’ Lee C. Moore derrick with stand. nominal shl rating 345k.

Substructure:
8.5’x 8.5’x 20’x 40’ Substructure, 6.5’x 5.5’x 20’x 40’ pony subs

Traveling Equipment:
160 ton Emsco shorty traveling block & hook (8 lines), 150 ton Rashsi 
swivel (new), 4 ¼” x 38’ hex kelly with drive bushings, rat hole, and mouse 
hole, set of two (2) Wooley tongs c-model with assorted tong heads.

Rotary Table:
17 ½” x 44” Salem rotary table with split bushings

Mud Pumps:
EMSCO-800 Tri-Plex Mud Pump Powered By 398 Cat (New), 
Gardner Denver Pz-7 Tri-Plex Mud Pumppowered by 379 CAT (refurb)

Mud System:
300 BBL mud pit, with de-gasser, de-sander, de-silter with one 
(1) electric centrifuge. 250 bbl mud pit with hopper and two (2) electrical 
centrifuges with plumbing. Brandt shale shaker. 100 BBL pre-mix / kill 
mud tank (two 50 bbl tanks).

Houses / Buildings:
Generator house with two (2) 3406 cat’s, two (2) 320 kw generators Gardner Denver 
air compressor. Top doghouse 8’x 20’. bottom doghouse 8’x 20’ with stand. Tool pusher trailer.

Auxilary Equipment:
one (1) set 5” drill pipe slips, one (1) set 6 ½” drill collar slips, new spool drill 
line 1” x 5,000’ with spool stand, three station oil lubricator, 5 station closing unit 
with lines (new), 5000 psi choke manifold, martin decker weight indicator with diaphragm 
(refurb), 57’ kelly hose (new), 50 bbl trip tank, 5’ x 5’ x 4’ junk box, 6’ x 6’ x 4’ junk box, 
5’ x 4’ x 55’ cat walk, three (3) sets of pipe racks 30’ x 4’ x 4’, 10’ x 20’ parts / work dog 
house, AOI rotary torque wheel and guage (new), oil works inc. / pip spinners (new), 
assorted hand tools, pipe wrinches, hammers, etc.

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------
Search Words(for official use only) :
Wilson 65 Mechanical Drilling Rig for Sale
870 HP Mechanical Drilling Rig for Sale
Mechanical Drilling Rig for Sale in USA
Wilson 65 Land Drilling Rig for Sale
Mechanical Drilling Rig - 870 HP
---------------------------------------------------------------------------------------------------

Worldrigs ID: WR2100

Ideco H35 Drilling Rig for Sale
600hp Refurbished Ideco H35 Drilling Rig for Sale 

Description :

Drawworks:  Ideco H35, powered by a Detroit 12.6L 600 HP engine, hydraulic make 
up and break out cathead, Pason Systems automatic driller, Pason Systems recorder, 
Allison 5860 transmission, hydromatic double brake

Mast:  Ideco 105’, 250,000#

Substructure:  200 Ton, 11’3” under rotary beams

Rotary Table:  Ideco SR-20.5

Block & Swivel: Ideco UTB 160 block, Ideco TL 200 with Foster spinner swivel

Mud Pumps:  (2) F-800 triplex pumps

Mud Pits:  dual vortex linear shaker, 3 cone desander, 12 cone desilter, 
600 bbl capacity, 50 BB slug tank, (1) Demco 5x6 mud mixing pump

BOP:  11” Hydril annular, 11” doule ram 3000#

Accumulator:  4 valve 80 gallon koomey with remote control on side of dog house

Light Plant:  (2) 60 series Detroit engines, 14L, 400KW Gen light plants

Kelly & Kelly Spinner:  5.25” Hex Kelly, Foster Kelly Spinner

Water Tank:  260 bbl with heated room for water pumps, hydraulic cylinder 
to raise D.H. to floor level

Elevators & Slips:  4.5” BJ MGG, drill pipe 100 ton, 5.5” BJ side door, 7” 50 Ton safty 
latch side door elevators, 4.5” Wooley D.P. slips, 5.5x7” Bash Ross D.C. slips

Drill Pipe:  6,500 ft. of 4 ½” G-105

Communications:  Cell phones and Pason satellite

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------
Search words (for official use only) :
Ideco H35 Drilling Rig for Sale in USA
Refurbished Ideco H35 Drilling Rig for Sale 
Refurbished Drilling Rig for Sale
600hp Ideco H35 Drilling Rig for Sale
1984 Built - 2000 Refurbished Drilling Rig for Sale
--------------------------------------------------------------------------------------------

Worldrigs ID: WR1220

Schramm T450 Drilling Rig for Sale
Used Schramm Drilling Rig for Sale

Model : T450 Drill Rig
Manufacturer : Schramm
Year : 1988
Condition : Used

Description : 

1988 Schramm T450 Drill Rig
Diesel Deck Engine
Air Compressor
Carousel
Centrifugal Pump
Pipe Rack
3 hydraulic leveling jacks
Mounted on a Truck
Diesel Engine

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

         

---------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Schramm T450 Used Drilling Rig for Sale
1988 Built Rig Schramm T450 for Sale
Schramm T450 Drilling Rig for Sale in USA
Schramm T450 Drilling Rig 1988 Built for Sale
Schramm Land Drilling Rig for Sale
Drilling Rig - Schramm T450 for Sale
-----------------------------------------------------------------------------

Worldrigs ID: WR2213

Lewco Cameron LDW 750K Drilling Rig for Sale
Used 1500hp Box on Box Drill Rig for sale

Drawworks
Lewco/Cameron LDW 750K 1500 HP , Low low rated
648,000#, single line pull, w/10 lines, w/2 AC 1150 input,
gear drive. Hydraulic Actuated, Parking disc brake,
1 3/8” wirerope 6x19 IWRC.

Prime Power
Omron/IDE 4 VFD System, (3) Cat 3512’s with Kato
1365KW AC Generators.

Auxillary
Cold start air system, primary rig air supply, floor hoisting
systems.

Mast/Substructure
DSI 152’, 750,000# hook load, with 12 lines strung, Singshot
design, 500,000# setback, Crown block (6) 50” sheaves 1 3/8”
groove,  Fastline (1) 60” 1 3/8” grooved.

Top Drive/Traveling Block/Pipe Handling
CanRig 1250 500Ton AC Top Drive, American Block B60F500
Block, RT 275, 27 ½” Rotary w/400HP AC input.

Mud Pumps
(2) Lewco WH-1612 1600HP, 5,000psi, each driven by (2)
1150HP AC input motors.

Mud System
(2) tank system, 1200 bbl capacity, (2) Swaco Mongoose shale
shakers, 6-Oil Works 15HP agitators, Derrick desander 2 12” cones
with 5x6 centrifugal driven by 100 HP electric motor, NOV Derrick
desilter 12 4” cones with 6x8 centrifugal driven by 100 HP electric
motor, NOV Derrick Vaccu Flow 1200 Degasser, 48 x 20 gas buster.

BOP Equipment
13 5/8” 5000# annular, 13 5/8” 5000# double ram, 3000 PSI accumulator,
120 gal, 5 station with remote, 4 1/16” 5000# x 2 1/16” 5000# choke
manifold.

Fuel Tank : 18,000 gal
Water Tank : 500 bbl

Auxiliary
Deadline Anchor, Weight indicator, Pump SPM and PSI,
manual Tongs, elevators, slips and clamps

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

------------------------------------------------------------------------------------
Search words (for official use only) :
Lewco Cameron LDW 750K Drilling Rig for Sale
Used Lewco Cameron LDW 750K Drilling Rig
1500 HP AC/VFD Land Rig for Sale
Used 1500hp Box on Box Drill Rig for sale
1500HP Lewco Cameron LDW 750K Drilling Rig for sale
------------------------------------------------------------------------------------

Worldrigs ID: WR2198

ZJ-40 Drilling Rig for Sale
1260hp ZJ-40 Drilling Rig for Sale
 
Derrick
JJ22538 mast with guylines, hydraulic raising and telescoping, max. capacity 2250kN,
windproof capacity with full setback, without hook load 110km/h, mast height 38m
14 X 8E Carrier Vehicle,drive type 14X8, max. speed(limited) 45km/h, climbing gradient
26%, min. Ground clearance 311mm, steering radius 19,5m 

Hydraulic cathead cylinder
Hidraulic outrigger
Mast Raising and telescoping cylinders
Drill pipe Set Back Area (Racking platform capacity: 10 setbacks 7”DC,
4000m 4 ½”DP or 3200m 5” DP

Drillfloor in derrick area 7,4m X 7,4m
Monkey Board
Derrick lighting system
Hydraulic cathead cylinder
Stairways to rigfloor
Hand railings
 
Substructure
Substructure  model ZZT 225D, max. load 2250kN, working height 6m, structure
Parallelogram, working space below rotary beam 4,9m

Catwalk
Pipe Racks
Crown block  model TC225, max. load 2250kN
Hook Block  model YG225, max. load 2250kN
Swivel SL 225, working load 0f main bearing 1500KN(100r/min),  max. work pressure 35MPa
Main oil pump, discharge capacity 208L/min, system pressure 21MPa/14MPa
TQ340-35 Casing Power Tong , Capacity 4 ½” – 13 3/8”
ZQ203-100 Drill Pipe Power Tong, 3 ½” – 5”
YZB-120 Hydraulic Power Station, Rated working pressure 16MPa
Pneumatic system, rated pressure 0,85MPa
 
Standpipe Manifold
Mud Valve Z23Y-35, 100mm - 5000psi
Standpipe 4 ½”
Rotary jumper hose (bottom standpipe)
Rotary Hose
Upper Kelly Valve
Kelly 5 1/4" Hexagonal
Kelly drive bushing - 5 1/4"
Lower Kelly Valve
Transmission box model Allison S6610HR, max. net input power 850HP, max.
input rotary speed 2500r/min, max. net input torque 3118N.m

Compounding box model BJX260B, max. input rotary speed 2500r/min, max. 
output torque 26000N.m
Drawworks model JC28/11D, Main drum fast line pull 280KN
CAT C18 Diesel Engine, Power 630HP/2100r/min
Auxiliary Brake model WCB236, brake power 970HP, brake torque 66611Nm,  
circulating water pressure 40 psi

Drill Line – 1 1/4" diameter
Drill Line Spool
Drillers Console
Rotary Table - 27 1/2", model ZP275, max. Rotary speed 250rpm, max. 
Net load 4500KN, max. Torque 27kN.m

Rotary drive box, model ZX140B, max input rotary speed 2100r/min, max. input
torque 14000N.m, Clutch model Axial thrust disk ATD318H

Masterbushing
Hydraulic winch model YJ3C, max. hoisting capacity 30KN
Hydraulic winch model YJ5B, max. hoisting capacity 50KN
 
BOP Control
B.O.P. Closing  Unit
Remote Control Panel
13 5/8" 5000 PSI Annular BOP  
B.O.P. 13 5/8", double studded  complete with 2" side outlets (double ram - blind/pipe rams)
associated spools  and DSA for BOP and Wellhead connections
Mud-Gas Separator
Choke Manifold 5000psi
BOP control hoses
 
Mud Treatment Package
ZG-58,4 Sand Control Tank (Shaker tank) with staircase
Shale Shaker  Model QZS 703 El. motor 1.72KW 1400RPM x 2
Vacuum Degasser Model ZCQ 300, El. motor 3KW 1470 r/min, El. motor 4KW 1435 r/min
FG-49,4 Cycle Tank
Model 200SB 240-40 Sentrifugal Sand Pump, Rate 240m3/h, Inlet Diameter-200mm,
Outlet Diameter-150mm, El. motor 55KW, 1480 r/min (For solids control system)

Desander Model LCS 250 x 2 with shale shaker, vibration el. motor 0.8KW 1410 r/min
Desilter Model CNQ 100 x 10, with shale shaker, vibration el. motor 0.75KW 1400 r/min
Centrifuge Model LW 450x842-N, El. motor 5.5KW 1440 r/min, El. motor  22KW 1470 r/min
FG-54,6 Cycle Tank (suction tank) with staircase
Agitator Model WNJ 11, El. motor 11KW 1460 r/min
Model 200SB 240-40 Sentrifugal Sand Pump, Rate 240m3/h, Inlet Diameter-200mm,
Outlet Diameter-150mm, El. motor 55KW, 1480 r/min (For mud hoppers)

Mud Hopper
Mudgun
Water tank - 500bbl Capacity,  with water pump
 
Mud Pumps
Mud Pump  F-1000, triplex,  rated stroke length 10”, Maximum WP 5000 psi
Suction  manifold – 12”
Charging pump, centrifugal, model SB200x150-310, lift 25m, flow 180m3/h, el. 
Motor 37KW, 1490r/min
Pump engine, model G12V190PZL-3

Generator Package
MSS System, model WB ZJ40-3
Power supply system FKS-V400
Diesel-Generator Set, model FKS-V400, Diesel engine TAD 1345GE, 
power 400KW, 400V, 1500rpm, 50Hz

Air supply system
Electric Control Panel
SULLAIR 3000 Compressors, max. W.P 210psi, max. temp. 2350F  with JYL 50F
Refrigerated Compressed Air Dryers

Air Receiver 3m3
FUEL SYSTEM
Fuel Supply  System
Fuel Tank – 50 m3  with fuel pump

Rigsite Accommodation
Container 20ft – Rig manager
5 Man bunkhouse units - container type caravan.
2 Man bunkhouse units – container type caravan with communal shower and toilet facilities.
8 man bunkhouse units – container type caravan with communal shower and toilet facilities.
Container 20ft for kitchen personal.
Container 20ft for Doctor.
Kitchen Galley -fully equipped kitchen and communal eating facilities
Storage container 20ft
Container mud lab. 

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
 please send us an email to mail@worldoils.com stating your
 requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
 ------------------------------------------------------------------------------------------
 Search words (for official use only) - 
ZJ-40 Land Drilling Rig For Sale
1260hp ZJ-40 Drilling Rig for Sale
ZJ-40 Drilling Rig for Sale
---------------------------------------------------------------------------------------------

Worldrigs ID: WR2209

JC40 DB Land Drilling Rig for Sale
Land Drilling Rig for Sale in USA

Description :

Drawworks: 
RG JC40DB  1000 HP, Low low rated 600,000#, single line pull, w/10 lines,
and one Hitachi 1240HP input, AC motor. Parking disc brake,
1 ¼” wirerope 6x19 IWRC.

Prime Power: 
Omron/IDE 4 VFD System, (3) Cat 3508’s with Avk 1256KW AC Generators.

Auxillary: 
cold start air system, primary rig air supply, floor hoisting systems.

Mast/Substructure: 
DSI 142’, 650,000# hook load, with 12 lines strung, Singshot design,
400,000# setback, Crown block (6) 50” sheaves 1 ¼” groove, 
Fastline (1) 60” 1 ¼” grooved.

Top Drive/Traveling Block/Pipe Handling: 
Varco TDS10SA VF AC 250Ton Top Drive,
YC225 250 Ton Block, Jpetro 27 ½” Rotary.

Mud Pumps: 
(2) RSF-1300HP, 5,000psi, each driven by (1) 1000HP AC input motor.

Mud System: 
(2) tank system, 1000 bbl capacity, (2) Swaco Mongoose shale shakers,
5-Oil Works 15HP agitators, Derrick desander 2 12” cones with 5x6 centrifugal driven
by 100 HP electric motor, NOV Derrick desilter 12 4” cones with 6x8 centrifugal
driven by 100 HP electric motor, NOV Derrick Vaccu Flow 1200 Degasser, 48 x 20 gas buster.

BOP Equipment: 
13 5/8” 5000# annular, 13 5/8” 5000# double ram, 3000 PSI accumulator,
120 gal, 5 station with remote, 4 1/16” 5000# x 3 1/8” 5000# choke manifold.

Fuel Tank:  16,500 gal

Water Tank:  500 bbl

Auxiliary:  
Deadline Anchor, Weight indicator,
Pump SPM and PSI, manual Tongs, elevators, slips and clamps

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
JC40 DB Land Drilling Rig for Sale
Land Drilling Rig for Sale in USA
Used 1000 Hp JC40 DB Land Drilling Rig for Sale
JC40 DB Used Land Drilling Rig for Sale
1000 HP JC40 DB Land Drilling Rig for Sale
---------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2194

Cabot 1500Hp Rig for Sale
1981 Built Cabot 1500Hp Land Drilling Rig for Sale

Specifications
Drawworks : Cabot 2550, 1500 HP, 715,000 lbs max line pull (10) lines, powered by
(2) EDM Electric, 800 HP each

Derrick :  127’ free standing, 735,000# gross capacity

Substructure :  22’ Cabot/Cross Type, 735,000 lbs capacity

Rotary Table :  27 ½” 400 Ton

Top Drive :  CanRig 602 AC, 275 Ton, 205 rpm, 30,000 ft/lbs max torque

Iron Roughneck :  Bloom & Voss Floor Hand

Traveling Block :  CanRig, 350 Ton

Floor Winches :  (2) Braden PD12C, 10000 lbs

Rig Power Plants :  (3) Kato AC 1050 KW, 1200 rpm, 600V, (3) Cat 3512

BOP :  (1) Shaffer 13 5/8” 5000 psi bag type preventer, (1) Hydrill Double
13 5/8” 5000 psi ram type preventer

Mud Pumps :  (2) Continental Emsco FB 1300, GE 752 DC Traction
motors, 800 HP each

Mud Tanks :  (2) 800bbl

Shale Shaker : (2) Swaco Venniem

Hydraulic Catwalk :  Pipe Wrangler

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------
Search words (for official use only) :
Cabot 1500Hp Rig for Sale
1981 Built Cabot 1500Hp Land Drilling Rig for Sale
Cabot 1500Hp Rig - 1981 Built - For Sale
Land Drilling Rig - Cabot 1500hp - For Sale
Used Land Rig for Sale
----------------------------------------------------------------------------------------------------

Worldrigs ID: WR1039

Portadrill TLS 471 Drill Rig for Sale
1980 Built Used Drilling Rig

Model : TLS 471 Drill Rig
Manufacturer : PortaDrill
Year : 1980
Condition : Used

Description :

Drilling Package
1980 Portadrill TLS 471 Drill Rig
Mounted on a 1979 Ford Truck
6V92 Trubo Diesel Engine
8V92 Turbo 475HP Diesel Deck Engine
671 Noster Tophead DH
Sulliar 950 cfm / 350 psi Air Compressor
1988 Western Star Water / Fuel Truck with 444 Cummins
250 Gallon Fuel Tank
1500 Gallon Water Tank
2005 Ford F350 4X4 1 Ton Flat Bed Truck
Smeal 5T Pump Hoist Service Rig, mounted on a 1990 Ford Truck
Calwel Drill Bucket Rig
50' Kelly Bar
Mounted on a 1975 Chevy Truck

Tooling Included in the Package:
Trailers, Drill Pipe, Mud Pump, Trash Pump, Hammer Bits, Hammers,
Tricones, Sub-Adapters, Casing Clamps

Location : USA

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------------------
Search words(for official use only) :
Portadrill TLS 471 Drill Rig for Sale
1980 Built Used Drilling Rig
Portadrill Drilling Rig For Sale
Portadrill TLS 471 Drill Rig in USA
1980 Built Used Drilling Rig Portadrill for Sale
Used Drilling Rig for Sale in USA
--------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2195

IDE AC 1500 Sparta Drilling Rig for Sale
2011 Built IDE AC 1500 Sparta Drilling Rig

Specifications

Drawworks :  IDE 1500 AC Sparta, 1500 HP, 757,000 lbs max
line pull (10) lines, powered by (1) General Electric 1500 HP motor

Derrick :  142’ telescoping, 750,000# gross capacity 

Substructure :  25’ IDE/Slingshot Style, 750,000 lbs capacity 

Rotary Table :  37 ½” 650 Ton 

Top Drive :  CanRig 1035 SC – 500, 350 Ton, 265 max rpm,
30,000ft/lbs max torque
 
Iron Roughneck :  Bloom & Voss Floor Hand 

Traveling Block :  American Block, 400 Ton 

Floor Winches :  (2) Braden PD12C Hydraulic, 12000 lbs 

Rig Power Plants :  (3) Kato AC, 1375 KW, 1200 rpm,
600V, (3) Caterpillar 3512 

BOP :  (1) Church Energy 13 5/8”, 5000psi bag type preventer,
(1) Townsen double 13 5/8”, 5000psiHydrill, 11” 5000psi 

Mud Pumps :  (2) Gardner Denver PZ11, powered by GE AC
1600 HP traction motor, 1600 power rating
 
Mud Tanks :  (2) 970bbl
 
Shale Shaker : (2) Brandt King Cobra
 
Hydraulic Catwalk :  Pipe Wrangler

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
 please send us an email to mail@worldoils.com stating your
 requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.
 ------------------------------------------------------------------------------------------
 Search words (for official use only) - 
IDE AC 1500 Sparta Drilling Rig for Sale
Used Land Drilling Rig for Sale
IDE AC 1500 Sparta Drilling Rig
2011 Built IDE AC 1500 Sparta Drilling Rig
Used IDE AC 1500 Sparta Drilling Rig - For Sale
---------------------------------------------------------------------------------------------

Worldrigs ID: WR2226

Cooper 750 Drilling Rig 750 hp For Sale
750 hp Drilling Rig 750 hp For Sale in USA

Desciption

Drawworks :
Cooper 750 DD Drawworks, 750hp, Grooved for 1 1/8" Drill Line,
Powered by (2) 425hp Detroit Diesel Series 60 Engines,
W/Allison CLT-5860 Trasmissions, Caliper Disc Brake,
Cooper (2) Engine In-Line Compound, Cooper Right Angle Gearbox,
Cooper Deadline Anchor, All Mounted On a Four Axle

Auxiliary Brake:
Kobelt Pneumatic 48"

Mast :
DSI 117' H Double Soping Mast, 410,000# Static Hook Load,
(5) Sheave Crown Cluster, Crown Safety  Platform, Racking Board,
Tong Counter Weights, Ladder, Derrick Climber, Geronimo,
4" Standpipe and Manifold

Substructure :
DSI 17'8"H, Scoping T-Style Substructure, 300,000# Set Back Capacity,
Rotary Beams, Stairs, Safety Railing, Elevated Roatry Drive

Top Drive :
TESCO 250 HMIS 475 Top Drive and Power Unit, Rated 475hp, 250 ton,
(2) Speed/Torque Ranges, 21,000# Max Continous Torque
W/Max 85 RPM and 10,000# Max Continous Torque W/Max 170 RPM

Mud Pumps :
Two (2) Gardner Denver PZ-9 Triplex Pumps, 1000hp, Each
Powered by 1100hp Caterpillar D399 Diesel Engines, Forged Steel Fluid
end Modules, Quick Change Caps, K-20-5000 Pulsation Damper,
OTECO 3" Shear Relief Valve, 1 1/2" x 2" Centrifugal  Rod Cooling Pump,
5" x 6" Charge Pump, 6,000 PSI Pressure Gauge, Chain Drive Assembly

Well Control :
Shaffer LWS 11" 5M Double RAM, Hydril GK 11" 5M Annular,
Choke Line (1) 4-1/16" Hose, Kill Line (1) 2 1/16" Hose,
(1) 2 1/16" GATE Valves, (2) 2 1/16" Hose,
(1) 2 1/16" Gate valve, (1) Check Valve

Choke Manifold :
Cameron Type 5M, W/5-Way Cross, (2) 4 1/16" X 5M Gate Valves,
(8) 2 1/16" X 5M Gate Valves, (8) 2 1/16" X 5M Gate Valves,
(2) 2 1/16" 5,000 PSI Pressure Guage, DSI 3' X 10' Degasser,
Mounted on 8'W x 16'L Skid

Accumulator :
Koomey Type 80 (5) Five-Sation Closing Unit, With (16) 11 Gallon Accumulator Bottles,
(1) Triplex Pump, (2) Air Pumps With 120:1 Ratio

Mud System :
Two (2) Tank Mud System of Approximately 800 BBL Total Capacity

Shaker Tank of Approximately 400 BBLS, (2) Vortex Fluid Systems
Orbital Shale Shakers, Odrill Desender W/(2) 10" Cones,
Odrill Desilter W/(12) 4" Cones, (2) 6' x 5" Series 250 Centrifugal
Pumps Powered By A 60 hp AC Electric Motor

Suction Tank of Approximately 400 BBls W/(2) 6" x 8" Series 250
Centrifugal Pumps Powered By A 60 hp AC Electric Motor, (4) 15hp
Mud Agitators, Vortex Ventures Shearing Hopper, Vortes Radial Eductors
in Mud Tanks

Trip Tank : 
28 BBLS W/2" x 3" Centrifugal Pump

Power Catwalk : Rahco Hydraulic, Handles Double Joints of
Drill Pipe and Range 3 Casing

Generation/Utility House :
Two (2) Caterpillar 350 KW AC Generators, Powered By 475HP
CAT C-15 Diesel Engines W/Electric Start, Air Compressors and MCC Panel

Block/Hook :
American Block, 250 Ton Block/Hook Combination, With (5) 36" Sheaves for 1 1/8" line

Rotary Table :
IDECO 17-1/2"

Water Tank :
400 BBL. Complete W/(2) MCM 2" x 3" Centrifugal Pump Driven BY 20hp AC Electric Motors

Fuel Tank :
10,000 Gallon W/(2) Roper 3 HP Fuel Tranfer Pumps

Drillers Doghouse :
Drillers Doghouse 25' x 8'2" x 9'3"

Auxilliary Equipment :
Two (2) PC12 Hydraulic Winches, (1) IR FA2.5 Man Rider Air Hoist,
Spinnmaster 950 Hydraulic Drill Pipe

Instrumentation :
Weight Indicator, W/Tong Line Pull, Pump Pressure & Rotary Torque Gauges,
Type "D" 5,000 PSI Mud Pressure Gauge

Wireline Machine :
Five Star Retriever W/15,000' OF .092 Wireline

Well Site Trailers :
TA Structures Rig Manager Trailer 54' x 12'6" x 11'8", Crew Bunk/Change House

Tubulars :
Drill Pipe and Collars Per Contract Requirements

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------------------
Search words (for official use only) :
Cooper 750 Drilling Rig for Sale
Cooper 750 Land Drilling Rig for Sale
750 hp Drilling Rig 750 hp For Sale in USA
Cooper 750 Drilling Rig 750 hp For Sale
---------------------------------------------------------------------------------------------------------------

Worldrigs ID: WR2224

Brewster N4 Drilling Rig for Sale
650 HP Trailer Mounted Rig For Sale

Description
 
Drawworks :
Brewster, Model N-4, Single Drum Drawworks, 650Hp, Lebus Grooved 
for 1-1/8" Line, Hydraulic Makeup & Breakout Catheads, Air Driller's Console, 
Crown-O-Matic, 8” water cooled brakes,

Compound :
Brewster 2-Engine, In-Line Compound

Brake :
D & H 15" Double Hydromatic Brake With jaw clutch

Drawwworks Power:
No. 1 - CATERPILLAR 3306 Diesel Engine 361HP, S/N 64Z33301
 w/ 24 Volt Electric Start, Radiator,Gauges,
ALLISON 955 Torque Converter.

No. 2 - CATERPILLAR 3306 Diesel Engine 361HP, S/N 64Z33298 w/ 
24 Volt Electric Start, Radiator,Gauges,
ALLISON 955 Torque Converter

Mast:
SPENCER HARRIS 97'H Cantilever Mast, 285,000 Lb. Static Hook Load, 
Crown Block w/ (4) 30" Sheave Cluster & (1) 30" Fastline Sheave, 1-1/8" Line, 
Racking Board, Tong Counter Weights, Ladder, DerrickClimber, Geronimo, 
4" Standpipe & Manifold

Carrier:
SPENCER HARRIS 40'L, Tri-Axle, Dual Wheel Trailer w/ Leveling 
Jacks, 57'8"L Back-On-Ramp, Fold Out Walkways, Deadline Anchor, 
Safety Rails.

Substructure:
SHOPBUILT 11'6"W x 16'H x 23'6"L Swing Up Substructure w/ 
Rotary Beams, (Refurbished in 2009)With Certifications, V Door Ramp, 
Stairs Safety Rails, Skidded.

Pump: (Primary)
GARDNER DENVER PZ9 Triplex Mud Pump, 1000 Hp. W / Forged 
Steel Fluid End, Quick Change Valve & Cylinder Head Caps, HYDRIL 
Pulsation Dampener, OTECO 3" Shear Relief Valve, Pressure Gauge,
Charging Pump, V-Belt Drive Assembly, Master Skidded w/ Engine

Pump Power:
CATERPILLAR D-398 Diesel Engine S/N 6685860 w/ Air Start, 
Radiator, Gauges, Mounted Pump Master Skid.

Pump: (Standby)
NATIONAL N1100 Duplex Mud Pump, 500 Hp. w/ Forged Steel 
Fluid End, Quick Change Valve & Cylinder Head Caps, 
HYDRIL Pulsation Dampener, OTECO 3" Shear Relief Valve, Pressure Gauge,
Charging Pump, V-Belt Drive Assembly, Master Skidded w/ Engine

Pump Power:
CATERPILLAR D-398 Diesel Engine S/N 66B5860 w/ Air Start, 
Radiator, Gauges, Mounted Pump Master Skid.

Rotary Table
Gardner Denver 27 -1/2" Rotary Table w/ Split Master Bushings, 
with raised floor

Swivel
BREWSTER 6S 220 Ton Swivel

Kelly
Kelly, Square drive , 5-1/4" x 37', with Kelly bushing

Kelly Valves
Upper Kelly Valve.
Lower Kelly Valve

Traveling Block / Hook
BREWSTER 175 Ton Block/Hook Combination, with elevator links

Blowout Preventer and Valves
SHAFFER LWS Double gate, Blowout Preventer 13 5/8" X 3,000 psi
13 5/8"Dia. x 30"H x 3 M Drilling Spools. 3,000 Psi. Choke Manifold. 
Choke Valves- Kill Valves-

Closing Unit
Closing Unit., 6 station, with drillers control panel
120 Gal 5 station accumulator w/remote

Rig Houses:
Dog House, 10'W x 50'L Doghouse w/ (4) Lockers, Knowledge Box, 
Parts Room, Bench Storage, (1) Heater, Air Conditioner, Lights, 
Skidded

Shopbuilt 8'W x 25'L Mud House w/ Pump parts Room, Mud Hopper, 
Heater, Lights, Skidded.

Utility Houses/Generators:
Utility House, 10'W x 50'L, Electrical Panel, Air Compressor, Transformer

No. 1 - DETROIT 350 Kw. AC Generator
Powered By DETROIT Series 60 Diesel Engine w/ Electric Start, Radiator, Gauges.

No. 2 - CATERPILLAR 234 Kw. AC Generator
Powered By Caterpillar, 3306, Diesel Engine w/ Electric Start, Radiator, Gauges
All above Mounted 12'W x 50'L Utility House w/ Parts Room, Lights, Skidded

Mud System:
Shopbuilt, 10'W x 6'H x 42'L, 432 Bbl. Suction Tank w19' Porch, 
(3) Compartment, (3) OILWORKS Pit boss 10 Hp. 
Mud Agitators p/b BALDOR 10 Hp. Electric Motors, 
Slant Bottom, Internal Plumbing,
Top Mounted Walkways, Safety Rails, Lights, Skidded. 
MISSION 5" x 6" Centrifugal Pump p/b TECO 50 Hp. Electric Motor

Shopbuilt 10'W x 6'H x 42'L, 432 Bbl. Shaker Tank w/ 9' 
Covered Porch, (4) Compartment,
(1) OILWORKS Pitboss 10 Hp. Mud Agitator S/N 2143 p/b BALDOR 10 Hp. 
Electric Motor, Slant Bottom,
Internal Plumbing, Top Mounted Walkways, Safety Rails, Lights, Skidded.
FIVE STAR 5" x 6" Centrifugal Pump p/b TECO 50 Hp. Electric Motor
FIVE STAR 5" x 6" Centrifugal Pump p/b TECO 50 Hp. Electric Motor
FLUID SYSTEMS, Single Screen, Linear Motion Shale Shaker S/N 2314
O'DRILL / MCM, Desilter w/ (8) 4" Cones
O'DRILL / MCM, Desander w/ 2 10" Cones

Water Tank
Shopbuilt 10'W x 8'H x 40'L, 549 Bbl. Water Tank w/Parts Room, Parts 
Bins, Lubester, Lights, Centrifugal Water Pump, with Dog house stand 
inside, Oilfield Skidded

Fuel Tank
Shopbuilt 8'W x 8'H x 30'L, 13,837 Gallon Fuel Tank w/ (2) Fuel Transfer 
Pumps, Oilfield Skidded

Trailers
20' Office trailer w/furniture

Miscellaneous Equipment Including

Approx. 6' X 20' Bubble buster flash tank
1 set type C tongs w/heads
12" x 400 x 10" crossover spool
41 Misc. handling and crossover subs
Wire line unit XCE serial # 01 006N4
2 pin ROP and weight indicator
2 sets slips
400K weight indicator
2 sets elevators
3" Marlow trash pump

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

--------------------------------------------------------------------------------------------
Search words (for official use only) -
Brewster 650 hp Trailer Mounted Rig for Sale
Brewster N4 Drilling Rig for Sale in USA
Brewster 650 hp Mechanical Drilling Rig
Brewster N4 Spencer Harris Trailer Mounted Rig
Brewster Land Rig in USA
--------------------------------------------------------------------------------------------

Worldrigs ID: WR262

National T45 Land Rig For Sale in Indonesia

We have for sale a complete mechanical rig in good working condition will current Silo certification. 
Located in Indonesia. 

The rig has all tools tubulars and camp and related plant and has just finished work in last few weeks and is presently stacked.
Please ask for full intentory.
More pictures on request. 

Price & terms : Please enquire using the email form below.

If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.

We can arrange delivery of equipment and towage of rigs and vessels where needed.

The details mentioned above are believed to be accurate but are not guaranteed.

---------------------------------------------------------------------------------------------------
Search Words(for official use only) :
National T45 Land Rig For Sale
Drilling Rig For Sale in Indonesia
Used Drilling Rig for Sale
Used land rig in Indonesia
Land Rigs for sale in Indonesia
---------------------------------------------------------------------------------------------------