Complete Jackup Drilling Package For Sale
Jackup Drilling Package For Sale
Rig Drilling Package
Used Drilling Package from a Rig For Sale
Offshore Drilling Package
This is a offshore driling package.
Offshore Drilling Package
Used Drilling Package from a Rig For Sale
Used Drilling Package for Sale
Rig Drilling Package
This is a drilling package including derrick, cantilever, texas deck etc,
which is coming available to the market because the drilling rig is
going to be converted into an accommodation rig.
Used Rig Drilling Package for Sale
A.1.1.1 Rig Floor Winches (Non Man-riding)
Quantity no. : 2
Make : Ingersol Rand
Type : K5UL
Rated capacity lbs : 5,000
Wire diameter inch : 1/2
A.1.1.2 Monkey Board Work Winch
Quantity no. : 1
Make : Ingersol Rand
Type : Airdyne
Rated capacity lbs : 1 ton
Wire diameter inch : 3/8
Automatic brakes yes/no : Yes
Overload protection yes/no : No
Quantity no. : 1
Make : Ingersol Rand
Type : Pullstar PS 1000R
Rated capacity lbs : 1 ton
Wire diameter inch : 3/8
Automatic brakes yes/no : Yes
Overload protection yes/no : No
A.1.1.3 Rig Floor "Man-Riding" Winch (Utility)
Quantity no. : 2
Make : RAM
Type : ML336 Catalina
Rated capacity lbs : 330
Wire diameter inch : 3/8”
Non-twisted wire yes/no : Yes
Automatic brakes yes/no : Yes
Overload protection yes/no : Yes
Automatic spooling yes/no : Yes
Certified for man-riding yes/no : Yes
A.1.1.3.1 BOP Service Area “Man-Riding” Winch(Utility)
Quantity no. : 2
Make : Ingersol Rand
Type : FA 150K Gi
Rated capacity lbs : 330
Wire diameter inch : 3/8”
Non-twisted wire yes/no : Yes
Automatic brakes yes/no : Yes
Overload protection yes/no : Yes
Automatic spooling yes/no : Yes
Certified for man-riding yes/no : Yes
A.1.1.4 Utility Winch (ie Deck Winch)
Quantity no. : 6
Make : Ingersol Rand
Type : K5UL
Rated capacity lbs : 10,000
Wire diameter inch : 3/4
Automatic brakes yes/no : No
Overload protection yes/no : No
Automatic spooling yes/no : No
Certified for man-riding yes/no : No Locations :
A.1.1.5 BOP Hoists (see E.10.1)
Quantity no. : 2
Make : BEEBE
Type : Overhead Bridge Crane
Rated capacity st : 37.5 tons / Crane
Location : Underside of drill package
B
General Rig Specifications
B.1 Derrick and Substructure
B.1.1 Derrick/Mast
Make/type : Joseph Paris
Rated for windspeed
- With full set back knots : 100
- With no set back knots : 100
Height ft : 162
Dimensions of base ft x ft : 36 x 36
Dimension of crown ft x ft : 18 x 18
Gross nominal capacity lbs : 1,485,714
Static hook load lbs : 1,300,000
Maximum number of lines no. : 14 (12 in use)
Ladders with safety cages and rests yes/no : Yes
Platform for crown sheaves access yes/no : Yes
Counter balance, system for rig tongs
pipe spinning tong yes/no : Yes
Lighting system explosion proof yes/no : Yes
B.1.2 Racking Platform
Make/type : Total capacity-drill pipe :
- 5" DP ft : 20,000
- 6-5/8" DP ft : 9,000
- 3-1/2" DP ft : 20,000
Total capacity-drill collars :
- 8" DC ft : 7 stands
- 9" DC ft : 3 stands
Tubing Bellyboard yes/no : No
B.1.3 Substructure
Make/type : CFEM
Drill floor height (above main deck) ft : 37.35
Width ft : 77.34
Length ft : 44.57
Setback capacity kips : 606
Simultaneous setback-hookload capacitykips : 1,200
Rotary beam capacity (total) kips : 903
Clear height below R/table beams (to main deck) ft :
B.1.4 Weather Proofing
Rig floor windbreaks yes/no : Yes
- Height ft :
Derrickman windbreaks yes/no : Yes
- Height ft :
Around process pits yes/no : Yes
- Height ft :
B.1.5 Derrick TV Camera System
Camera located at : Monkey board level in derrick
Make/type : Ocular 12EX PTZ EExd Camera
Zoom/pan/tilt-function yes/no : Yes
Monitor located at : Drillers house (Ocular 4M EEx de 11G T6 Monitor)
Camera located at : Stabbing board level
Make/type : Ocular 12EX PTZ EExd Camera
Zoom/pan/tilt-function yes/no : Yes
Monitor located at : Drillers house (Ocular 4M EEx de 11G T6 Monitor)
B.2 Drawworks and Associated Equipment
B.2.1 Drawworks
Make/type : National 1625 DE
Motors make/type : Jeumont Schneider DC 752
- Quantity no. : 2
- Rated input power hp : 1,000
Motors make/type : GE DC 752
- Quantity no. : 1
- Rated input power hp : 1,000
Drum size (dia & length) in x in : 36 x 61-1/2
Drum type (grooved/smooth) : Grooved
- For drill line size in : 1-1/2
Brake type (disc/drum) : Drum
Max line pull (12 lines) lbs : 1,250
Max line pull (10 lines) lbs : 1,075
Max line pull (8 lines) lbs : 880
Makeup cathead type : Foster
Breakout cathead type : Foster
Crown block safety device :
- Make/type : National Crown-o-Matic
Independent fresh water cooling system
for drawworks and electric brake yes/no : Yes
Automatic driller yes/no : No :
B.2.2 Auxiliary Brake
Make : Elmagco
Model : 7838
Independent back-up system type : KEMS
B.3 Derrick Hoisting Equipment
B.3.1 Crown Block
Make/type : Joseph Paris (overhauled)
Rated capacity st : 715
No. of sheaves no. : 8
Sheave diameter inch : 60
Sheave grooved for line size inch : 1.5
B.3.2 Travelling Block
Make/type : National / Type H, 760H650
Rated capacity st : 650
No. of sheaves no. : 7
Sheave diameter inch : 60
Sheave grooved for line size inch : 1.5
B.3.3 Hook
Make/type : National / Type H-650
Rated capacity st : 650
Complete with spring assbly/hook yes/no : Yes
locking device
B.3.4 Swivel
Make/type : National / P-650 (Integrated with TDS-4S)
Rated capacity st : 650
Test/working pressure psi : 5,000
Gooseneck and washpipe min id in : 3
Left hand pin connection type : 7-5/8 Reg
Access fitting for wireline entry yes/no : Yes on top of gooseneck
B.3.5 Drilling Line
Diameter inch : 1-1/2
Construction : 6 x 19 IPS IWRC
Length (original) ft : 7,500
Drilling line reel :
- Drum cover yes/no : Yes
- Drilling line drum power drive yes/no : No
Spare drilling line yes/no : No
Location (rig, shore, etc) : Rig
Roller guides yes/no : Yes
B.3.6 Dead Line Anchor
Make/type : National / Type EB
Weight sensor yes/no : Yes
Dead line dampener yes/no : Yes
B.3.7 Block Guidance System
Make/type : BSI Track & Dolly/ non-retractable
B.4 Rotating System
B.4.1 Rotating Table
Make / type : National C-495
Maximum opening inch : 49-1/2
Rated capacity st : 800
Two speed gearbox yes/no : Yes
Emergency chain drive yes/no : No
Driven by an independent electric motor yes/no : Yes
- Electric motor type/make : Jeumont Schneider
- Maximum continuous torque ft/lbs :
- Output power hp : 1,000
Drip pan/mud collection system yes/no : Yes
B.4.2 Master Bushings
Make/type : Varco
Inserts bowls (see G.1.8) : No. 1, 2, 3, DP/DC
B.4.3 Top Drive
Make : Varco TDS-4S
Type (electric/hydraulic) : Electric
Rated capacity st : 650
Test/working pressure psi : 5,000
Output power hp : 1,100
Maximum continuous torque ft/lbs : 45,500 Low Gear / 29,500 High Gear
Two speed gear box yes/no : Yes
Maximum rotary speed rpm : 125 Low Gear / 205 High Gear
Remote operated kelly cock yes/no : Yes
Cooling system type : Close Loop System (remote blower)
B.4.3.1 Top Drive Makeup/Breakout System
Make/Type : Varco/Torque Wrench/Pipe Handler
Model : PH-85
Max makeup torque ft/lbs : 85,000
Max. breakup torque : ft/lbs : ,000
Raised backup system : yes/no : No
- Make/type :
C Power Supply Systems
C.1.1 Compressed Air Systems
Air compressors - low pressure (bulk air) :
- Quantity no. : 1
- Make : Ingersol-Rand
- Model : 650L
- Rated capacity ft3/min : 750 cfm
- Working pressure psi : 40
- Prime mover (electric/diesel) : Electric
- Continuous power hp : 154.5
Air dryers:
- Quantity no. : 1
- Make/type : R800A Pioneer Refrigerated Air Dryer
- Rated capacity ft3/min : 100 btu/min 100 SCFM to ambient
C.1.2 Air Receivers
Quantity no. : 1
Volume (total) ft3 : 2.25 m3
Pressure psi : 125
Location : Drill Floor
D Drillstring Equipment
D.1.1 Drill Pipe
Drill pipe OD inch : 5
Grade : S-135
Total jnts : 137
Range : Weight lbs/ft : 19.5
Internally plastic coated yes/no :
Tool joint OD/ID in/in : 6-5/8 - 3-1/4
Tool joint pin length (original) inch : 6-3/4
Tapered shoulder tool joints (box/pins)degree : 18
Connection type : 4-1/2 IF Bevel : 5-59/64 in
Type of hardfacing : Arnco 200XT (6000 ft)
API classification : Premium
Thread protectors yes/no : Yes
Installation tools (manual, hydraulic, none) :
Drill pipe OD inch : 5-1/2”
Grade : EU-S
Total jnts : 310
Range :
Weight lbs/ft :
Internally plastic coated yes/no :
Tool joint OD/ID in/in :
Tool joint pin length (original) nch :
Tapered shoulder tool joints (box/pins)degree :
Connection type :
Bevel :
Type of hardfacing :
API classification :
Thread protectors yes/no : Yes
Installation tools (manual, hydraulic, none) :
D.1.2 Hevi-Weight Drill Pipe
Quantity no. : 1
Nominal size OD inch : 5
Weight lbs/ft : 49.5
Range : 2
Tool joint OD / ID inch : 6-1/2 / 3
Type of hardfacing : Hughes Smooth AX@
Internally plastic coated yes/no : Yes
Connection type : 4-1/2 IF
Thread protectors yes/no : Yes
Quantity no. : 45
Nominal size OD inch : 5-1/2” Spiral
Weight lbs/ft :
Range :
Tool joint OD / ID inch :
Type of hardfacing : Hughes Smooth AX@
Internally plastic coated yes/no : Yes
Connection type :
Thread protectors yes/no : Yes
D.1.3 Drill Collars
Quantity no. : 6
OD body inch : 8-1/4
ID body inch :
Nominal length of each joint ft : 31
Drill collar body (slick/spiral) :
Spiral Recess for "zip" elevator yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no :
Boreback on box yes/no :
Connection type : 6-5/8
REG Quantity no. : 8
OD body inch : 8
ID body inch : 2.813
Nominal length of each joint ft : 31
Drill collar body (slick/spiral) :
Spiral Recess for "zip" elevator yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no : Yes
Boreback on box yes/no : Yes
Connection type : 6-5/8
REG Quantity no. : 8
OD body inch : 6.5
ID body inch : 2.813
Nominal length of each joint ft : 30
Drill collar body (slick/spiral) :
Spiral Recess for "zip" elevator yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no : Yes
Boreback on box yes/no : Yes
Connection type : 4 IF
Quantity no. : 12
OD body inch : 6-1/2”
ID body inch :
Nominal length of each joint ft : 31
Drill collar body (slick/spiral) :
Spiral Recess for "zip" elevator yes/no : Yes
Recess for slips yes/no : Yes
Stress relief pin groove yes/no :
Boreback on box yes/no :
Connection type :
Quantity no. :
OD body inch :
ID body inch :
Nominal length of each joint ft :
Drill collar body (slick/spiral) :
Recess for "zip" elevator yes/no :
Recess for slips yes/no :
Stress relief pin groove yes/no :
Boreback on box yes/no :
Connection type : 6-5/8
REG Quantity no. : 8
OD body inch :
ID body inch :
Nominal length of each joint ft :
Drill collar body (slick/spiral) : Spiral
Recess for "zip" elevator yes/no :
Stress relief pin groove yes/no :
Boreback on box yes/no :
Connection type :
D.1.4 Inside BOP Valve
Quantity no. : 1
Make : TIW
OD inch : 5
Min. drill pipe ID required inch : 3-1/4
Connection type : 4-1/2 IF
Working pressure rating psi : 10,000
D.1.5 Kelly Cocks
Upper inside BOP (see also D.1.15)
- Quantity no. : 1 upper
- Make/type : Varco
Working pressure psi : 15,000
Max OD body in : 7-3/4
Max ID body in : 3
Connection type (box) : 7-5/8 Reg
Connection type (box) : 7-5/8 Reg
Lower inside BOP Manual
- Quantity no. : 1 lower
- Make/type :
Working pressure psi : 15,000
Max OD body in : 7-3/8
Max ID body in : 3
Connection type (box) : 7-5/8
Connection type (pin) : 7-5/8
D.2 Handling Tools
D.2.1 Hydraulic Makeup/Breakout Machine (e.g. EZ Torque)
Make/Type : Ezy Torque
Maximum linepull : 35,000 lb
D.2.2 Iron Roughneck
Make/type : Varco AR 3200
Size range (max OD/min OD) in/in : 3-1/2 / 9-1/2
Max makeup torque ft/lbs : 90,000
Max breakout torque ft/lbs : 100,000
E Well Control
E.1 Diverter
Fixed yes/no : No
- Make/type :
- Maximum bore in :
- ID of insert packer in :
- Working pressure psi : Annular yes/no : Yes
- Make/type : Hydril MSP
- Maximum bore in : 29-1/2
- Working pressure psi : 500
Bottom connection : Flanged
- Size in : 30
- System pressure psi : 1,500 working
- Gasket type : R-95
Number of diverter outlets no. : 2
Outlet OD (nominal) in : 12
E.1.1 Diverter Flowlines
Quantity no. : 1
Nominal size of flowlines
Running from diverter to : Overboard (aft)
Valve make/type : Ball
- Quantity no : 2
- Size in : 12
- Working pressure : 500
- Valve operator (air/hydraulic) : Hydraulic
System pressure rating psi : 500
Flex hose in flowline Yes/no : No
E.1.2 Diverter Control Panel
Primary make/type : Koomey
- Location : Under Cantilever
Remote make/type : Koomey / Type 80
- Location : Driller’s house and Toolpusher office
E.2 High Pressure Blowout Preventers
All appropriate components H2S rated yes/no : Yes
E.2.1 Kill Line Valves
Quantity no. : 2
Make/type : Cameron
Size : 3-1/16
Working pressure psi : 15,000
Gasket type : BX-154
Hydraulic/manual/non-return : 1manual & 1 hydraulic
E.2.2 Choke Line Valves
Quantity no. : 2
Make/type : Cameron
Size in : 3-1/16
Working pressure psi : 15,000
Gasket type : BX-154
Hydraulic/manual no. : 1 manual & 1 hydraulic
E.3 BOP Control System
E.3.1 Accumulator Unit
Make/model : Koomey Type 80
Location Inside hull
Fluid reservoir capacity US gal : 502
Oil/water mix rate US gpm : Hydraulic oil (Oceanic HW-540)
Glycol reservoir capacity US gal : None
Total accumulator capacity (w/o precharge) USGal : 210
System working pressure psi : 3,000
Control manifold model : Koomey
Regulator type : KR
Total useful accumulator volume equals all
preventer opening and closing volumes yes/no : Yes
- Plus percent additional volume % : 50%
E.3.2 Accumulator Hydraulic Pumps
Electric driven :
- Quantity no. : 2
- Make/model : Koomey
- Each driven by motor of power hp : 30
- Flow rate of each pump US gpm : 142
- At operating pressure psi : 3,000
- Operable off emergency generator yes/no : 1 - normal power, 1 - emergency generator
Air driven yes/no : Yes
- Quantity no. : 2
- Make/model : Koomey / U9A26
- Flow rate of each pump US gpm : 6.4
- AT operating pressure psi : 3,000
E.3.3 Primary Control Panel
Control panel make/model : Koomey
Location : Under cantilever
Panel controls for the following functions :
- All annular BOPs yes/no : Yes
- All ram BOPs yes/no : Yes
- Lock for ram BOPs yes/no : No
- Diverter System yes/no : Yes
- Kill and choke line valves yes/no : Yes
- Low accumulator pressure warning yes/no : Yes
- Low reservoir level warning yes/no : Yes
- Low rig air pressure warning yes/no : Yes
- System pressure regulator yes/no : Yes
- Pressure regulator for annular yes/no : Yes
- Flowmeter yes/no : Yes
- Quantity of pressure gauges no. : 5
- Other control functions yes/no : No
E.3.4 Remote Control Panels
Make/model : Koomey Zone I
Location : Rig floor
Location : TP office
Ability to operate main closing unit valves
directly yes/no : Yes
System routing (direct/thru panel) : Direct
Remote control of system pressure
regulator yes/no : Yes (from the Drill Floor)
Remote control of annular pressure
Regulator yes/no : Yes (from the Drill Floor)
E.4 Choke Manifold
All appropriate components H2S rated yes/no : Yes
E.4.1 Choke Manifold (For instrumentation, see H.3)
Nominal size in : 3-1/16
Minimum ID in : 3.063
Maximum working pressure psi : 15,000
Quantity of fixed chokes no. : 1
- Make/model : Demco
- Size (ID) in : 3
Quantity of adjustable chokes no. : None
- Make/model :
- Size (ID) in :
Quantity of power chokes no. : 2
- Make/model : Demco
- Size (ID) in : 2 in max
Power choke remote control panel yes/no : Yes
- Make/model : Demco
- Location : Driller’s house
- Glycol injection yes/no : No
E.5 Flexible Choke &Kill Lines
(BOP to Manifold)
Quantity no. : 2
Make/type : Hose
ID in : 3
Working pressure psi : 15,000
H2S service yes/no : Yes
E.6 Flexible BOP Control Hoses
Quantity no. : 16
Make/model : Hydrasun
Size (ID) in : 1
Working pressure psi : 3,000
Fire resistant yes/no : Yes
E.7 BOP Testing Equipment
E.7.1 Hydraulic BOP Test Pump
Make/model : Koomey
Type : Air
Pressure rating psi : 30,000
Chart recorder yes/no : Yes
E.7.2 BOP Test Stump
Size in : 13-5/8, 15,000psi
E.8 BOP Handling
E.8.1 BOP Hoist System
Make/type : BEEBE Quantity of hoists no. : 2
Number of lift points on BOP no. : 2
System safe working load (max BOP wt) st : 2 x 37.5 tonnes
E.8.2 Work Platforms
BOP work platform (adjustable/fixed/none) : Fixed
Conductor pipe platform yes/no : Yes
E.8.3 Conductor Pipe Tensioning System
Make/type : Hydril
Tension capacity st : 300 kips
Number of lift points no : 4
Stroke in : 16
F Mud System / Bulk System
F.1 High Pressure Mud System
System working pressure psi : 5,000
System test pressure psi : 5,000
F.2 Mud Pumps
Quantity no. : 3
Make : National-Oilwell
Model : 12-P-160
Type (triplex/duplex) : triplex
Mud pump drive motors no. : 2
- Motor type : Jeumont Schneider DC 752
- Continuous power rating per motor : 1,600 hp
Mud pump drive motors no. : 1
- Motor type : GE DC 752
- Continuous power rating per motor : 1,600 hp
Fluid end type : Southwest
- Maximum working pressure psi : 5,000
- Test pressure psi : 5,000
Pump stroke counter type : Martin Decker
Supercharging pump type : Mission
- Driven by motor of power hp : 75
Discharge suction line ID inch : 12
M.P Pulsation dampener type : Hydril
Reset relief valve : Retsco Type B Working flowrate per pump at
90% of max gpm : 600 gpm
- Liner size inch : 6-1/2
- Pump speed (90% of max) spm : 120
- Pump pressure psi : 3,900
- Working flowrate US gpm : 514
F.2.1 Transfer Pumps / Mixing Pumps
Mixing Pumps :
- Quantity no. : 2
- Make/model : Mission Magnum 1
- Type/size : Centrifugal / 8x6R
- Output capacity US gpm : 1,200
- Drive motor type : Electric
- Power output hp : 75
Transfer Pumps :
- Quantity no. : 2
- Make/model : Mission Magnum 1
- Type/Size : Centrifugal/8 x 6R
- Output capacity US gpm : 1,200
- Drive motor type : Electric
- Power output hp : 75
F.2.2 Standpipe Manifold
Quantity of standpipes no. : 2
Standpipes ID inch : 4 (5-9/16” OD)
H-Type standpipe manifold yes/no : Yes
Kill line outlet yes/no : Yes
Fill-up line outlet yes/no : Yes
Bleed-off line outlet yes/no : Yes
F.2.3 Rotary Hoses
Quantity no. : 1
Make/type :
ID x Length inch x ft : 3-1/2 x 80
Working pressure psi : 5,000
Snubbing lines yes/no : Yes
F.2.4 Cementing Hoses
Quantity no. : 1
Type (armor sheath/flexible steel pipe) : Steel internal wound Rubber
Length ft : 80
ID Inch : 2
Working pressure psi : 10,000
F.3 Low Pressure Mud System
F.3.1 Shale Shakers
Primary :
- Quantity no. : 3 (brand NEW not commissioned even)
- Make/model : Axiom AX1
- Type :
- Nominal flow rate (total) bbl/min : Variable up to 1000gpm per shaker
dependent on screen size and fluid properties
F.3.2 Mud/Gas Separator (Poor Boy)
Make/type : Swaco
Dimensions (height x OD) ft x in : 10 ft x 4 ft
Gas discharge line ID in : 8 in
Gas discharge location, primary : Crown A-frame
Can discharge be tied into burner system : No
Vacuum break yes/no : Yes
Mud seal height ft : 24
Pressure gauge yes/no : Yes
Calculated gas throughput mmscf : 17.83
F.3.3 Degasser
Make/type : Wellco 5200
Nominal flow rate bbl/min : 600
Feed pump make/model : Mission 6 x 8
- Type/size :
- Capacity gpm : 1,200
- Drive motor hp hp : 75
Is pump dedicated to degasser yes/no : Yes
Vacuum pump make type : Wellco
F.3.4 Mud Agitators
Quantity no. : 1
Make/model : Swaco SWM-5
Driven by motor of power hp : 5
Located in tanks : Slug pit
(see F.2.1 & F.2.2 for tank designations)
Quantity no. : 4
Make/model : Swaco SWM-25
Driven by motor of power hp : 25
Located in tanks : Tanks 1, 2, 3, 4
(see F.2.1 & F.2.2 for tank designations)
F.4 Bulk System
F.5 Barite/Bentonite Silos
Quantity no. : 4
Capacity of each silo ft3 : 1307
Locations : P/tank room
Type weight loadcell : Martin Decker
Manufacturer : Totco
Pressure rating psi : 40
Relief valve(s) installed yes/no : Yes
F.5.1 Cement Silos
Quantity no. : 4
Capacity of each silo ft3 : 1307
Locations : P/tank room
Type weight loadcell : Martin Decker
Manufacturer : Totco
Pressure rating psi : 40
Relief valve(s) installed yes/no : Yes
Separate mud/cmt loading facilities yes/no : Yes
Cement discharge independent from
barite/bentonite yes/no : Yes
F.5.2 Surge Tank for Barite/Bentonite
Quantity no. : 2
Capacity of each tank ft3 : 70 ft3
Type weight loadcell : Totco
- Manufacturer : Totco
Pressure rating psi : 20
Relief valve(s) installed yes/no : Yes
F.5.3 Mud Hopper
Quantity no. : 2
Make/model : Double Life Jetting
Feed pump make/model : ASF.12
Type/size : Capacity bbl/min : 1,200
Drive motor hp hp :
Is feed pump dedicated to mud hopper(s) yes/no : No
G Casing / Cement Equipment
G.1 Cementing Equipment
G.1.1 Cementing Manifold
Discharge manifold working pressure : 15,000 psi
Cement pump discharge lines min ID : 2 in
Cement pump discharge lines
working pressure psi : 15,000
Manifold safety pressure relief valve yes/no : Yes
G.1.2 Cementing Standpipe
Quantity no. : 1
Working Pressure psi : 15,000
ID inch : 3
Connection to choke manifold yes/no : Yes
Connection to standpipe manifold yes/no : Yes
H Instrumentation/Communication
H.1 Drilling Instrumentation at Driller's Position
H.1.1 Weight Indicator
Make/type : Martin Decker / Type E-80
Sensor type : AWE 9-1
H.1.2 Standpipe Pressure Gauges
Quantity no. : 1
Make/type : Martin Decker
Max. pressure reading psi : 5,000
Quantity no. : 1
Make/type : Martin Decker
Max. pressure reading psi : 5,000
H.1.3 Choke Manifold Pressure Gauge
Quantity no. : 1
Make/type : Stewart & Stevenson
Max. pressure reading psi : 15,000
Quantity no. : 1
Make/type : Martin Decker
Max. pressure reading psi : 15,000
H.1.4 Rotary Instrumentation
H.1.4.1 Tachometer
Make/type : Martin Decker
Maximum RPM rpm : 250
H.1.4.2 Torque Indicator
Make/type : Martin Decker
Maximum torque ft/lbs : 50,000
H.1.5 Top Drive Instrumentation
H.1.5.1 Tachometer
Make/type : Martin Decker
Maximum RPM rpm : 250
H.1.5.2 Torque Indicator
Make/type : Martin Decker
Maximum torque ft/lbs : 50,000
H.1.6 Pump Stoke Counters
Quantity no. : 2
Make/type : Totco
Stoke indicator and cumulative
Stroke counter for each pump : Yes
H.1.7 Tong Torque Indicator
Make/type : Martin Decker
Maximum torque ft/lbs : 25K x tong length
H.1.8 Pit Volume Totalizer
Make/model: Electro Flow
Floats in active mud tanks : Yes
- Quantity per tank : no. : 1
Floats in reserve mud tanks : Yes
- Quantity per tank no. : 1
Floats in mud processing tank : Yes
- Quantity per tank : no. : 1
Loss/gain indicator yes/no : Yes
Audio Alarm yes/no : Yes
Visual Alarm yes/no : Yes
H.1.9 Mud Flow Indicator
Make/model : Electro Flow
High/low Alarm : Yes
- Audio Alarm yes/no : Yes
- Visual Alarm yes/no : Yes
Sensor location : Flow line
H.1.10 Trip Tank Indicator
Make/model : Electro Flow
Chart recorder yes/no : Yes
Alarm yes/no : Yes
H.2 Drilling Parameter Recorder
Quantity no. : 1
Make/type : Petron Drill Graf
Location - 1 : Driller’s house
- Type (display/recorder/both) : Display
Number of parameters recorded no. : 6
Parameter recorded : Weight
Parameter recorded : Pump pressure
Parameter recorded : Rotary torque
Parameter recorded : Rotary RPM
Parameter recorded : Pump SPM
Parameter recorded : Penetration rate
Brand new Electro wave Transocean Driller’s display system,
not commissioned yet.
H.3 Instrumentation at Choke Manifold
H.3.1 Standpipe Pressure Gauge (Drillpipe Pressure Gauge)
Quantity no. : 1
Make/type : Houston Digital Display
Pressure range (max.) psi : 6000
Visible from choke operation position : Yes
H.3.2 Choke Manifold Pressure Gauge (Casing Pressure Gauge)
Quantity no. : 1
Make/type : Houston Digital Display
Pressure range psi : 6000
Visible from choke operating position : Yes
H.4 Instrumentation at Standpipe
H.4.1 Standpipe Pressure Gauge
Quantity no. : 2
Make/type : MD Totco
Pressure range psi : 8000
Visible from drillers position : Yes
Visible from choke operation position : Yes
H.5 Rig Communication Systems
H.5.1 Rig Telephone System
No. of stations no. : 67 extensions
Make/type : Panasonic KXDT 1232
Explosion proof yes/no : Yes
H.5.2 Public Address System
Can be combined with H.6.1 above: yes/no : Yes
No. of stations no. : 67 (access from all telephones)
Make/type : Federal Signal Dual Redundant
Explosion proof yes/no : Yes - where applicable
H.5.3 Drill Floor Talkback System
No. of stations no. : 2
Location : Drill floor
Location : Monkey board
Make/type : Gaitronics
Explosion proof yes/no : Yes
H.6 External Communications Equipment
I Workover Tools
J Accommodation
J.1 Living Quarters
J.1.1 Accommodation Block
Total beds: no. : 43
- No. of beds per room type (1, 2, 3, etc.) no. : 2 (1 ea. 1 man)
- Number of rooms no. : 22
- Toilets (shared) no. : 0
- Showers (shared) no. : 0
Total beds: no. : 43
K Safety Equipment
K.1 General Safety Equipment
K.2 Rvival Equipment
K.2.1 Lifeboats
Make/type : Survival craft 75 C
Quantity no. : 4
Capacity (person/craft) : 60
Locations (port, stbd) : Port and stbd
Fire protection yes/no : Yes
Radio/EPIRB (see Section H.9) : NO
K.2.2 Davits
Davits : 4 ea.
Make : Survival craft inspectorate
Type : Rig Master SWL : 8.5 T
Class : DNV
Year : 2008
Price & terms : Please enquire using the email form below.
If you cannot find the vessel, crane, rig or equipment that you need,
please send us an email to mail@worldoils.com stating your
requirements and we shall find it for you.
We can arrange delivery of equipment and towage of rigs and vessels where needed.
The details mentioned above are believed to be accurate but are not guaranteed.
--------------------------------------------------------------------------------------------------------
Search words (for official use only) -
Jackup Drilling Package For Sale
Offshore Drilling Package
Drilling Package For Offshore for sale
Complete Drilling Package For Sale
Complete Jackup Drilling Package For Sale
Jackup Used Drilling Units for Sale
Rig Drilling Package
Used Drilling Unit Form a Jackup Rig
-------------------------------------------------------------------------------------------------------
.png)
.png)
.png)
.png)
.jpg)
.png)
.png)
.png)
.png)
.png)
.png)
.png)
Search Here
