Max Payload (for offshore) : 32,910 lbs, 14,930 kgs Refrigeration : Daikin, Carrier Transicold or Thermo King Set temperature range : -35ºc to +30ºc in ambient up to +50º Control : Integrated Microprocessor control unit. Slings : Units supplied with DNV certified slings Designed, Built and Certified - BS EN 12079:2006, DNV2.7-1, ISO/CSC
Double Drum Wireline Unit Truck Mounted With Mast Country of origin USA - Drum assembly is of all steel, non-cast construction with a capacity of 25,000 feet. 108 in wireline. A large diameter drum shaft with pillow block design bearings is incorporated. - Drum assembly is on raised supports for operator convenience. - Drum assembly is of all steel, non-cast construction with a capacity of 25,000 feet . 125 inch Wireline. A large diameter drum shaft with pillow block design bearings is incorporated. - Drum assembly is on raised supports for operator convenience. - Brake assembly is of dual wide brake bands offering good stopping, holding, and heat dissipation characteristics. - Dual mechanical brake levers, operator adjustable, is installed at the operator’s console. - Drive assembly is a double chain and sprocket drive with tensioning system. - A four speed transmission for even more pulling power is installed offering a wide array of drum speeds and line pulls. Hydraulic motor will drive the transmission. - The drum and hydraulic system is capable of fast acceleration and fast deceleration. - Dog clutch assembly is used for shifting between the drums. - Power drive assembly is by a split shaft power take off installed at the truck transmission. - Shifting lever is at the driver’s cab. The power take off will drive the hydraulic pump. - Hydraulic assembly is of open loop design, 2,000 psi working pressure and 3,000 psi available for intermittent duty. - A rugged duty pump and motor is installed and controls is by a directional control valve with variable drum speed control. - A main relief valve, remote control relief valve and cross port relief valve is installed. - The cross port relief valve will used to control pressure spikes and give added protection for the hydraulic motor which occurs when hard duty jarring and other activities are occurring. A safety type pressure gauge, dual scale, is installed to monitor system working pressure. - Hydraulic fluid is supplied from a large capacity reservoir with breather/strainer filler cap and sight level/ temperature gauge. Filtration is by a suction strainer and a return filter with bypass feature which can allow a wireline job is finished when filter becomes clogged before a filter change needs is made. - A filter condition monitoring gauge is installed. All hoses and fittings is sized for maximum flow. - Operator’s cabin is of all steel construction and is approximately 6 foot front to back by 8 foot wide x 6 foot high, interior dimensions. - The walls, floor, and ceiling is well insulated and a FRP paneling material is installed at walls and ceiling. - A large viewing window is installed behind the drum assemblies with opening windows at entry door. - Heavy duty hinges and refrigerator type latch is installed at entry door. - Entry access door is installed driver’s side of body unless otherwise requested. - A fold down step is incorporated for ease of access to the operator’s compartment. - A well-padded observer’s bench is installed across rear of the cabin and will have storage area under. - A well-padded operator’s seat, with back rest, is installed at the operator’s console area. - Operator’s console is installed inside of the cabin assembly and behind the drum assembly. - All controls is installed with operator safety, comfort, and efficiency in mind. - Truck body is of flatbed design and will have a diamond pattern tread plate flooring installed. - US Dot lighting is installed as well as mud flaps. - Underbody tool boxes is installed’ quantity of four. Step rear bumper is installed. - Truck body is of flat bed design and all steel construction with a step rear bumper and diamond pattern flooring and rear skirting. A fabricated head ache rack is installed behind the driver’s cab. - The body is installed onto the truck chassis. - Mast is installed at the rear of the body. The mast is of hydraulic operation. - The mast will reach to 55 feet above the ground.` - A lubricator storage rack will lie down on the top side of the mast and is set up to allow the lubricator to stay clamped in position. - Outriggers is installed at rear of the truck body, one each side, and is used to level the truck before mast operations begin. The outriggers is independent of one another and is hydraulically operated with controls at rear tailboard of the body. - Performance is approximately 1400 feet per minute drum speed and 1400 pounds pull at mid drum and in 3rd gear on the transmission unless otherwise requested by the customer. - Performance testing is to MW strictest standards. - Routine maintenance is made easy - Two sets operation, parts, maintenance manuals on the wireline unit is supplied with the equipment. - Lighting 12 volt DC, both sides of the drum assemblies and interior of the cabin. - Climate control roof mount air conditioner 120 volt AC and hot water heater 12 volt DC - 2007 4400 HD International Truck 33,000 GVW
-------------------------------------------------------------------------------------------------------- Search words (for official use only) -
Multicat Vessel For Sale 2008 built - Used Multicat For Sale 1440bhp Multicat Vessel For Sale
General data : Built : 2008 GRT / NRT : 231 / 70 tons Specifications Length : 26.00 m Breadth : 11.00 m Depth / draft : 3.25 m / 2.50 m
Main engine / generator : Main engine : 2 x caterpillar 3412C DITA 720 bhp @ 1800 rpm Gear box : ratio = 4.5 : 1 Generator : 2 x cummins 6BT5.9 - G3 staford @ 85 kW 50 hz Propeller / kort nozzle : 2 x 4 blades manganese bronze propeller c/w mild steel kort nozzle
Tank capacity : Fuel oil tank : 90 cub.mt Fresh water : 45 cub.mt
Deck machinery : Anchor windlass : 2 x electrical hydraulic anchor windlass having capacity 2.0 tons @ 10 m / min single gypsy suitable for 19 mm dia. Stud link chain Anchor : 2 x 380 kg stockless bower anchor Chain cable : 10 shackles of dia. 19 mm x 27.5 m. Stud link cable Towing winch : 1 x single drum winch with 100 tons brake holding with winding load 40 tons Crane : Sormec knuckle boom swl 9.5 ton @ 6.5 m
Navigation / communication equipment : Radar : JRC JMA 1800 SSB radio : JRC JSB 196 GPS : JRC NWZ 4570 Compass : daiko magnetic compass VHF : JRC VHP 200 Epirb : mcmurdo E3 Echo sounder : JRC PLOT - 500 Navtex receiver : JRC NCR 330A PA system : 1 x horn speaker
Engine room : Oily water seperator : China type 0.25 / cu.m / hy Fuel filter : main engine only twin racor type Blower fan : 2 x 19" for engine room
Shafting / stern tube : Water lubrication stern tubes with cutlass bearing & bronze stuffing box 2 lengths stainless steel (AISI 316) shaft
Price & terms : Please enquire using the email form below.
If you cannot find the vessel, crane, rig or equipment that you need, please send us an email to mail@worldoils.com stating your requirements and we shall find it for you.
We can arrange delivery of equipment and towage of rigs and vessels where needed.
The details mentioned above are believed to be accurate but are not guaranteed. ---------------------------------------------------------------------------------------------------------------- Search words (for official use only) : Multicat Vessel for Sale Used multicat vessel for sale - 1440bhp Multicat for sale in Singapore Multicat boat for sale in Asia 1440bhp Multicat Vessel for sale Multicat vessel - 2008 built Used 2008 built Multicat Vessel Multicat boat for sale in Singapore ----------------------------------------------------------------------------------------------------------------
Single Drum Winch for Lease - Markey Model DES 26 Markey Model DES 26 Single Drum Winch Deep Water Winches for Hire Offshore Winch for Charter Offshore Winch for Hire - 140,000 lbs. at Bare Drum Specifications Line Pull : 140,000 lbs. At Bare Drum Cable Capacity : 1½” cable 4,500' Single Drum Winch : 23,000 lbs Hydraulic Power Unit (HPU) : 8,500 lbs Approx. Air Required : 100psi ; 375 cfm Water : 80 GPM for heat exchanger Male Cam Lock : 2 in Female Cam Lock : 2 in Input and Discharge Hose : 50 ft Cable Diameter : 2 in Price & terms : Please enquire using the email form below. If you cannot find the vessel, crane, rig or equipment that you need, please send us an email to mail@worldoils.com stating your requirements and we shall find it for you. We can arrange delivery of equipment and towage of rigs and vessels where needed. The details mentioned above are believed to be accurate but are not guaranteed. ------------------------------------------------------------------------------------------------------------------ Search words (for official use only) - Single Drum Winch for Lease Markey Model DES 26 Single Drum Winch for Lease Deep Water Winches for Hire Marine Deck Winch For Charter Marine Winch for Rent - - 140,000 lbs. at Bare Drum Rig Winch for Lease Markey Model DES 26 - Single Drum Winch for Charter -------------------------------------------------------------------------------------------------------------------------
Jackup Rig For Sale MLT-84S Jackup Rig For Sale Used Jack Up Rig For Sale Please note : Only very basic data is displayed here. If you wish to know more, please send us an email to mail@worldoils.com or used the email form at the bottom of this page.
Type of Rig : Offshore Drilling Unit Self Elevating MODU - MLT 84S Year Built : 1976 Class : ABS
Overall Length : 247' 7" Overall Width : 239' 5 1/2 " (including heliport) Main deck to rig floor height : 26'
Max variable deck load - operations : 7136 kips Max variable deck load - transit : 4368 kips
Lightship Displacement : 10,004 Tons Displacement at loadline draft : 12,166 Draft at loadline : 15' 6" Draft at lightship : 7'
Deck crane : 3 nos.
Total leg length : 421' Usable leg length : 416' Spud can diameter : 46'
Subject to prior sale
The details mentioned above are believed to be accurate but are not guaranteed. -------------------------------------------------------------------------------------------------------------------- Search words(for officia use only) - Jackup Rig for Sale MLT-84S Jackup Rig For Sale Jackup Rig Dealers Jackup Rig Builders Jackup Rig For Sale - Le Tourneau Jack up Rig Sellers Used Jackup for sale -----------------------------------------------------------------------------------------------------------------------
SCR Land Drilling Rig for Sale Refurbished 1500 HPSCR Land rig for sale National 110 UE Refurbished 1500HP SCR Rig
Specifications : National 110 UE 1500HP Single Drum Drawworks p/b (2) 1000 HP Apollo 752 DC Traction
Swivel : Mud King 450â€Ton Block/Hook : Ideco 525â€Ton Block/Hook Combination.
The details mentioned above are believed to be accurate but are not guaranteed. --------------------------------------------------------------------------------------------------------------------- Search words (for official use only) : SCR Land Drilling Rig For Sale Land Drilling Rig For Sale - 1500hp Used 1500 HP SCR Drilling Rig 1500HP Electric Drilling Rig For Sale ----------------------------------------------------------------------------------------------------------------------------
Specifications
Immediate delivery
Ideco H 44 Model 750 HP 6 axle Trailer mounted Rig for sale Used Trailer Mounted Rig for Sale 750hp Ideco Trailer Mounted Rig
Saturation Dive Winches for sale Winches for Sale Description The winch system consists of 3 winches: Bell winch, Clump-weight winch and Umbilical winch. Both the Bell and Clump-weight winches are man-riding. All 3 winches come completewith auto-spooling and local control. Bell Winch x 1 Max ratedpull : 12mT at top layer Max ratedspeed : 20m/min at top layer Drumcapacity : 250m x Æ34mm SWR StaticBrake-holding : 18mT at top layer Controls : 2 x PVG32 proportional valves Clump-weight Winch x 1 Max ratedpull : 8mT at top layer Max ratedspeed : 20m/min at top layer Drumcapacity : 500m x Æ26mm SWR StaticBrake-holding : 12mT at top layer Controls : 2 x PVG32 proportional valves Umbilical Winch x 1 Max ratedpull : 2.5mT at top layer Max ratedspeed : 20m/min at top layer Drumcapacity : 250m x Æ94mm umbilical StaticBrake-holding : 3.75mT at top layer Controls : 2 x PVG32 proportional valves The winches is LR (LloydsRegister) approved and are intended for 0°C to 60°C operating ambience. Inspection : Singapore Price & terms : Please enquire using the email form below. If you cannot find the vessel, crane, rig or equipment that you need, please send us an email to mail@worldoils.com stating your requirements and we shall find it for you. We can arrange delivery of equipment and towage of rigs and vessels where needed. The details mentioned above are believed to be accurate but are not guaranteed. -------------------------------------------------------------------------------------------------------------------- Search words (for official use only) - Saturation Diving Winches Winches for sale Saturation Diving Winches For Sale --------------------------------------------------------------------------------------------------------------------------
Diedrich Rubber Track Sonic Drilling Rig for Sale Sonic Drilling Rig on Tracks for Sale
Model : Sonic Drill Rig on Tracks Manufacturer : Diedrich Year : 2012 Condition : Used
Description :
2012 Diedrich Rubber Track Sonic Rig Engine : 375hp Volvo Diesel Engine Dimensions : Length towered down – 22’ 5” Length towered up – 21’ 6” Height towered down – 10’ 9” Height towered up – 22’ 7” Width – 8’ Weight – 37,600lbs Feed System : Dual single link chain drive Pull back – 20,000lbs Pull down – 20,000lbs Max speed – 102ft./min Rubber isolation wheels 15ft stroke, with a Gore track hose system Water Pumps : L6 Progressive Cavity Moyno Pump 225 PSI 47 GPM Inlet/Outlet – 3”/ 2-1/2” Jib Winch : Extended Position Capacity – 1700 lbs. Vertical Position (Over the hole) Capacity – 3800 lbs. Breakout Wrenches : 3-1/2” OD Pipe – 11” OD Pipe Torque 17,500 lbs. Mast : 12” x 12” structural tubular construction 25,000 lb. gross load rating 6” guide tubes Leveling Jacks : Four 36” stroke (2 front and 2 rear) Other Features : One 24” tool box 150-gallon fuel tank 200-gallon hydraulic tank Radio controlled under carriage Rod trough Automatic SPT Hammer 10” wiggle and 10” in/out Tooling available cost extra
Note : The majority of drilling projects the rigs now perform is Geotech drilling, Auto-Matic-Trip Hammers were installed on both.
Location : USA
The details mentioned above are believed to be accurate but are not guaranteed.
--------------------------------------------------------------------------------------------------------- Search words (for official use only) : 2012 Built Diedrich Rubber Track Sonic Drilling Rig for Sale Diedrich Rubber Track Sonic Drilling Rig - 2012 Built for Sale Drilling Rig - Diedrich Rubber Track Sonic - For Sale Used Diedrich Rubber Track Sonic Drilling Rig for Sale Diedrich Rubber Track Sonic Drilling Rig for Sale in USA -------------------------------------------------------------------------------------------------------
Anchor Handling Tug/Supply vessel for sale AHTS - 5150bhp for sale
Particulars Year Built : 2010 Length overall : 55.00 metres Beam, moulded : 13.80 metres Depth, moulded : 5.50 metres Draft, max operating : 4.76metres Accommodation : 24 persons
Classification American Bureau of Shipping A1 Circle E “Offshore Support Vessel, Fire Fighting Vessel Class1” + AMS
Performance Speed, ahead 12.5 knots Bollard pull 65 tonnes
Capacities Fuel 410.0m3 Freshwater 490.0 m3 Foam 11.0 m3
Main Engine 2x Cat 3516B, 2 x 2575 bhp
Propulsion Berg Controllable pitch propeller Generator 3x Caterpiller 3406, 3 x 245kw 415v/3ph/50Hz Navigation & Communication GMDSS A1+A2+A3 Deck Machinery Towing winch : 1 x 150 tonnes line pull C/W Spooling Gear : brake holding 200 tonnes Tugger Winches : 2 x 5 tonnes @ 15m/min Capstans : 2 x 5 tonnes @ 15m/min Deck crane : 1 x 3 tonnes at 1.7m Shark jaw : 200 tonnes SWL After deck area : 29m x 11.4m = 330.6 sq.m Tow wire : mini 1000m x 50mm dia Stern Roller : 5m long x 1.6m dia (SWL 200t) External Fire Fighting Equipment Fire pump : 2×1500 m3hr Fire monitors : 2×1200 m3/hr Water spray system : Yes
---------------------------------------------------------------------------------------------------------------- Search words(for official use only): Anchor Handling Tug/Supply vessel - 55m for sale 55m AHTS for Sale 5000bhp AHTS for sale AHTS for Sale in Asia AHTS for sale in Singapore Supply vessel for sale -------------------------------------------------------------------------------------------------------------
Hydraulic Clamping Device
Floating Crane For Sale Floating Crane For Sale - 35MT SWL Floating Crane For Sale in Baltic Sea
We can arrange delivery of equipment and towage of rigs and vessels where needed. The details mentioned above are believed to be accurate but are not guaranteed.
------------------------------------------------------------------------------------------------------------------ Search words (for official use only) - Floating Crane For Sale 35T Floating Crane For Sale Used Floating Crane For Sale Floating Crane For Sale in Baltic ------------------------------------------------------------------------------------------------------------------------
55Ton BP ASD Tugs for sale ASD Tugs Z-Peller for sale
Particulars of the 2 units ASD Tug Delivered 1983 – Australian Shipbuilding, WA 35.01m x 11.16m x 4.25m (draft) 2 x Niigata 8L27.5X 2,100bhp @775rpm (ttl 4,200bhp) Niigata Z-Peller Approx 55t BP LR Class, SS due 2013 Price & terms : Please enquire using the email form below.
---------------------------------------------------------------------------------------------------------------- Search words(for official use only) : Used ASD tugs for sale ASD Tugs for sale 55Ton bollard pull ASD tugs for sale 55Ton BP ASD tugs -------------------------------------------------------------------------------------------------------------------------
National 80-B - 1000 HP drilling Rig for Sale Used 1000HP Drilling Rig for sale 1985 built 1000 HP drilling rig for sale Drawworks/Brake National 80-B S/D Drawworks, S/N 2734, 1000hp, LEBUS Grooved f/ 1-1/4” Drill Line, National makeup and breakout catheads, Air drillers console, Crown-o-matic w/ PARMAC v-200 Hydromatic brake, S/N 56357
Compound National 2- Engine sectional compound, Each section mounted on 10’w x 34’3”l Covered skid w/ Fluorescent lights
Engines No. 1 : CAT D-398 Diesel engine, S/N 66B07426 (2007 metered hours) w/ Air starter, Radiator, Gauges, OILWORKS C-300-64 Torque converter, S/N 4924, Mtd on Compound skid
No. 2 : CAT D-398 Diesel engine, S/N 66B3172 (1860 metered hours) w/ Air starter, Radiator, Gauges, OILWORKS C-300-64 Torque converter, S/N 1632, Mtd on Compound skid
Mast/Substructure United Rig Services 136’h Cantilevered mast, S/N I-253, 750,000# Static hook Load, Crown block w/ (6) 48” Crown sheaves & 60” Fast line sheave grooved 1-1/4”, Crown safety platform, Racking board w/windwalls, Tong counterweights, Ladder, 4” Standpipe & manifold, Mast stand
21’h x 29’8”w x 69’l Stepdown box-on-box substructure w/rotary beams, v-Door ramp, Ideal 300tm deadline anchor, 400-Gallon air receiver tank, (4) Roughneck heaters, Cantilevered doghouse supports on drillers side and Off- drillers side, Stairs, Safety rails
Ingersoll rand KFU 4000# air hoist, Mtd in sub
Ingersoll rand K5UL air hoist S/N RAM061024C, Mtd in Sub
Ingersoll rand SSR up series 15-30HP air compressor, S/N PX822V06363 p/b 30 hp electric motor, Air receiver tank, Mtd in sub
Quincy QSB-40 air compressor, S/N UN087608 p/b BALDOR 40 hp electric motor, Air receiver tank, Mtd in sub
Mud Pumps CSF 1300 triplex mud pump, S/N 2006-8, 1300 hp, Forged steel fluid end w/ quick- change valve & Cylinder head caps, 5000# Pulsation dampener, 3” Shear relief valve, M&I type F 6000# pressure gauge, Rod cooling pump, V-belt drive assembly p/b CAT D-399 diesel engine, S/N 35B6050 (4594 metered hours) w/ air starter, Radiator, Gauges, Mtd on 12’W x 37-1/2’L covered skid
CSF 1300 triplex mud pump, S/N 2006-6, 1300 hp, Forged steel fluid end w/ quick- change valve & Cylinder head caps, 5000# Pulsation dampener, 3” Shear relief valve, Rod cooling pump, V-belt drive assembly p/b CAT D-399 diesel engine, S/N 35B06348 (3482 metered hours) w/ air starter, Radiator, Gauges, Mtd on12’W x 37- 1/2’L covered skid
Rotating Equipment RT-275 27-1/2” rotary table w/ 53-1/4” centers, Split master bushing
National N-815 400-ton swivel, S/N t-4536
5-1/4” x 41’l hex kelly w/ shuck
Varco hd Pin-drive kelly bushing, Dressed 5-1/4” hex
Upper & lower kelly valves
Traveling Equipment Ideco “shorty” 400-ton block/hook combination, S/N 40303AGIP w/ (6) 52” sheaves, Grooved 1-1/4” Set (2) 3” x 108” elevator bails
Well Control Equipment Hydril GK 15-5/8” 5000# annular BOP
Shaffer LWS 13-5/8” 5000# double ram BOP
13-5/8”, 5000# x 24” h drilling spool w/ (2) 3-1/8”,5m &(1) 2-1/16”,5m gate valves
OCO 5-Station closing unit, S/N 1102-51w/(12) accumulator bottles, CPC triplex hyd pump p/b WEG 15 hp electric motor, (2) Air-actuated hyd pumps, Approx 200-gallon hyd reservoir, Mtd on 8’w x 40’l Skid w/ (2) double life 5” x 6” cent pumps, S/N’s 8418 & 8489, Each p/b WEG 75 hp electric motor
Closing unit remote control panel (Number of stations undetermined because panel was lying face down at the time of inspection and was too heavy to lift by hand)
5000# choke manifold w/ 5-way cross, (2) 3-1/8”,5m &(5) 2-1/16”,5m ball valves, 2- 1/16”,5m adjustable choke, M&I type F 6000# pressure gauge, Mtd in 9’w x 16’l insulated house w/ fluorescent lights, skidded
Utility House/Generators No. 1 : CAT SR-4 500 kW ac gen set, S/N N/A, p/b CAT 3412 diesel engine, S/N 38S4885 (0 metered hours) w/ electric starter, Radiator, Gauges, Skidded
No. 2 : CAT SR-4 500 kW ac gen set, S/N 5NA0381 p/b CAT 3412 diesel engine, S/N N/A, (5056 metered hours) w/electric starter, Radiator, Gauges, Skidded
Both gen sets Mtd in 12’w x 41’l utility house w/ round-top, Electrical control Panel, Squared 75 kva transformer, Fluorescent lights, Skidded
Rig Houses 10’w x 41’l Toolpushers quarters, Fully furnished w/ office, Bedroom, Toilet & Shower facilities, Kitchen & Recreational area, Skidded
7’ 10”w x 24’l Doghouse w/ 6-1/2’l covered porch, Knowledge box, Bench storage, (4) Lockers, Parts shelves, Tool board, Air conditioner, Space heater, Fluorescent lights, Skidded
7’8”w x 36’l Off-side driller’s parts house w/ parts shelves, Power washdown unit, Fluorescent lights, Skidded
10’w x 20’l Change house w/ v-top, (21) Lockers, Insulated walls, Air conditioner, Qmark space heater, Squared 75 kva transformer, Fluorescent lights, Skidded
6’w x 32’4”l 3-Sided house w/ Roughneck heater, Skidded
Mud System 9’9”w x 8’h x 40’l 550-Bbl mud suction tank w/ 10’4”L pump room, (3) Compartments, (1) MAXX 2000 5 hp, (1) MAXX 2000 10 hp, & (1) MAXX 2000 20 hp mud agitators, Internal pumbing, (2) 5” x 6” cent pumps each p/b electric motor, Mud hopper, Top-mounted walkways, Stairs, Safety rails, Skidded
9’9”w x 8’h x 40’l 550-Bbl mud shaker tank w/ 10’4”l pump room, (3) Compartments, (2) MAXX 2000 20 hp mud agitators, Internal plumbing, (2) MCM 5” x 6” cent pumps, S/N’s 12844 &12846, Each P/b WEG 75 hp Electric Motor, Top-mounted walkways, Stairs, Safety rails, Skidded
(2) Swaco mongoose single, Single-screen linear motion shale shaker, S/N’s MPR- 472 & MPR-480, Swaco Desilter w/(12) 4” Cones & Swaco Desander w/(2) 12” Cones, All Mtd together to comprise mud cleaning unit
MCM 3” x 4” cent pump, S/N 11428 P/b Baldor 50 hp Electric motor, Skidded w/Lifting frame
MCM 5” x 6” cent pump, S/N 11014 p/b Baldor 50 hp Electric motor
Fuel/Water Tanks 7’8”w x 9’h x 30’l 15,000-gallon fuel tank w/ 7’l pump room, (2) flow serve fuel transfer pumps each p/b baldor 5 hp electric motor, 4-compartment lubester, Skidded 9’9”w x 8’h x 35’l 480-Bbl water tank w/ 7’4”l pump room, (2) MCM 2” x 3” cent pumps each p/b baldor 20 hp electric motor, Skidded
Handling Tools Rauch MFG Inc. 512AX Pipe spinner, S/N 1208-462-3/22-7073 Set (2) BJ type db rotary tongs w/ Asst’d jaws WTM 350-ton 5”bn drill pipe elevator Various DP & DC slips Related Equipment 5’w x 18”h x 50’l 2-section catwalk w/ steel deck (14) 8’w x 34’4”l & (2) 8’w x 10’l steel framed rig mats MD Totco Type E 750,000# weight indicator w/ (3) pump pressure, (1) tong-line pull, & (1) Rotary torque gauges, Mtd in console
Five star “Retreiver” wireline measuring device Approx 2000’ of 1-1/4” drill line w/ Spool stand 3-1/2” id x approx 65’l Rotary hose (2) 3-1/2” id x 12’l Vibrator hoses 7’4”w x 4’h x 35’l Junk box (7) dc Lift subs
Approx (6) Misc. crossover & Saver subs (2) Kelly spinners (missing air motors) Lincoln “Ranger” Portable Welder P/b Kohler 20 hp engine Mission magnum 3” x 4” cent pump (no motor) Teco 30 hp electric motor Fluorescent and Mercury-vapor rig lights Misc. spare parts, Hand tools, Valves, Fire Extinguishers, Etc.
Drill Pipe/Collars/Pipe Tubs & Racks Approx 7500’ of 5” grade G-105, 19.50# range 2 drill pipe w/ 4-1/2” if bn tool Jts., 6” to 6-1/8” OD (Drill pipe stored in pipe tubs with solid steel ends which prohibited getting an accurate joint count)
(23) 6-1/4” to 6-3/8” OD x approx 30’l Spiral and Slick drillcCollars (mostly spiral) w/ 4-1/2” XH Conn
(4) 7-5/8” to 7-3/4” OD x approx 30’L Spiral drill collars w/ 6-5/8” reg Conn (5) 7’10”w x 3’h x 35’l Pipe tubs (3) Sets (6) 20”h x 28’l Triangular pipe racks (1) Set (2) 42”h x 28’l Triangular pipe racks
---------------------------------------------------------------------------------------------------------------------- Search Words(for official use only) : National 80-B - 1000 HP drilling Rig for Sale Used 1985 built 1000hp Drilling rig - National 80-B Used National 80-B drilling rig for Sale Land Drilling Rig For Sale 1985 built 1000HP drilling rig for sale 1000HP Used National 80-B Drilling Rig for Sale ------------------------------------------------------------------------------------------------------------------------------
Semi Submersible Drilling Rig for sale Used Semi Submersible drilling rig For Sale - 1974 built
Please note : Only very basic data is displayed here. If you wish to know more, please send us an email to mail@worldoils.com or use the email form at the bottom of this page General : Built : 1974 Class : ABS
Principal Characteristics and Dimensions : Lower hull length : 290' 0" Overall width of lower hull (excluding anchor racks) : 200' 0" Overall width of lower hull (over anchor racks) : 228' 0"
Capacities/Areas : Drill water : Lower hulls - 15,680 bbls Main Deck : 27,422 sq. ft. Drill Floor (clear area) : 500 sq. ft.
Drilling Loads : Hook : 1,000 kips Rotary : 800 kips Set back : 660 kips Subject to prior sale Price & terms : Please enquire using the email form below.
The details mentioned above are believed to be accurate but are not guaranteed. ------------------------------------------------------------------------------------------------------------- Search words(for official use only) - Semi Submersible Drilling Rig For Sale Old Semi Submersible Drilling Rig For sale Used Semi Submersible Drilling Rig for sale 1974 built Semi Submersible Drilling Rig For sale -----------------------------------------------------------------------------------------------------------------
Showing 1057 to 1104 of 2131 results
.png)
.png)
.png)
.png)
.jpg)
.png)
.png)
.png)
.png)
.png)
.png)
.png)
Search Here
11346757276642.jpg "Ingersoll-Rand T3 (Truckn 3) Drill Rig - 1975 built - for Sale")
11346757276642.jpg "Ingersoll-Rand T3 (Truckn 3) Drill Rig - 1975 built - for Sale")
1621511698769.jpg "Crew Boat - 157ft - for Sale")
1621511698769.jpg "Crew Boat - 157ft - for Sale")
1629720823293.jpg "Offshore Supply Vessel - For Sale")
1629720823293.jpg "Offshore Supply Vessel - For Sale")
